2005-2008 RAV4 · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Aug 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. DISCHARGE FUEL SYSTEM PRESSURE procedures must be performed before disconnecting any part of the fuel system.
  2. After performing the DISCHARGE FUEL SYSTEM PRESSURE procedures, pressure will remain in the fuel line. When disconnecting the fuel line, place a cloth or equivalent over fittings to reduce the risk of fuel spray.

  1. Remove the console box (Click here).

  1. A128750E01
    Disconnect the connector.

  1. Start the engine. After the engine has stopped, turn the ignition switch off.

    HINT:
    DTC P0171 (system too lean) may be set.

  1. Check that the engine does not start.

  1. Remove the fuel tank cap, and let the air out of the fuel tank.

  1. A128750E01
    Connect the connector.

  1. Install the console box (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


3. REMOVE NO. 1 ENGINE COVER

  1. A124558
    Remove the 2 nuts and engine cover.


4. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

  1. A124559
    Disconnect the mass air flow meter connector.

  1. Disconnect the purge VSV connector.

  1. Disconnect the 4 wire harness clamps.

  1. A124560
    Disconnect the No. 2 ventilation hose from the air cleaner hose.

  1. Disconnect the purge line hose from the clamp.

  1. A124561
    Squeeze the tabs of the No. 1 air cleaner hose clamp, and then disconnect the No. 1 air cleaner hose from the throttle body.

  1. A124562
    Unfasten the 2 hook clamps, and then remove the air cleaner cap.

  1. Remove the air cleaner filter element from the air cleaner case.


5. DISCONNECT FUEL TUBE

A125337E01

NOTICE:
Do not forcibly bend and twist the fuel main tube.

  1. Remove the fuel tube from the fuel hose clamp.

  1. Remove the fuel pipe clamp.

  1. Wipe off any dirt on the fuel tube connector.

  1. Hold the fuel tube connector, and then install the SST.

    SST
    09268-21010  

  1. Turn the SST to align the retainer inside the fuel tube connector with the chamfered part of the SST.

  1. Insert the SST into the fuel tube and hold it. Then push the fuel tube connector toward the SST side.

  1. Mount the retainer of the fuel tube connector onto the chamfered part of the SST.

  1. A076220E05
    Slide the SST and fuel tube connector together towards the fuel tube until they make a "click" sound, and then disconnect the fuel tube.

  1. Drain the fuel remaining inside the fuel tube.

  1. Cover the fuel tube and fuel pipe with a plastic bag to protect the disconnected part.


6. DISCONNECT NO. 2 VENTILATION HOSE

  1. A097786E01
    Disconnect the No. 2 ventilation hose from the ventilation valve.


7. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

  1. A125333
    Remove the 2 wire harness clamps.

  1. Disconnect the 4 fuel injector connectors.

  1. A125334
    Remove the 2 bolts and then pull out the fuel delivery pipe together with the 4 fuel injectors.

    NOTICE:
    Be careful not to drop the fuel injectors when removing the fuel delivery pipe.

  1. A125335
    Remove the 2 delivery pipe spacers from the cylinder head.

  1. Remove the 4 insulators from the cylinder head.


8. REMOVE FUEL INJECTOR ASSEMBLY

  1. A097399E02
    Pull the 4 fuel injectors out of the fuel delivery pipe.

← REMOVAL (Jan 2007 – Jul 2007)INSPECTION (from Nov 2005) →