2005-2008 RAV4 · Service Manual ENGINE

P0335 Crankshaft Position Sensor "A" Circuit

Diagnostic trouble codes · Vehicles built from Jan 2007

Also covers:

Versions by build date: Nov 2005 – Dec 2006 from Jan 2007

DESCRIPTION

The crankshaft position sensor system consists of a crankshaft position sensor plate and a pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of an iron core and magnet. The sensor plate rotates, and a pulse signal is created as each tooth passes by the pickup coil. The pickup coil generates 34 signals for each engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine RPM. Using these calculations, the common rail injection system is controlled.
DTC No.
DTC Detection Condition
Trouble Area
P0335
No crankshaft position sensor signal to ECM while cranking
(1 trip detection logic)
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. Crankshaft position sensor No. 1 plate
  4. ECM
P0339
No crankshaft position sensor signal is input to ECM for 0.05 seconds or more, and conditions (a), (b) and (c) are met:
(1 trip detection logic)
(a) Engine speed is at 1,000 rpm or more
(b) STA signal is OFF
(c) 3 seconds or more have elapsed after STA signal is switched from ON to OFF
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. Crankshaft position sensor No. 1 plate
  4. ECM

WIRING DIAGRAM

C128772E01

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).


1. INSPECT CRANKSHAFT POSITION SENSOR

  1. A072395E09
    Disconnect the B42 crankshaft position sensor connector.

  1. Measure the resistance of the sensor.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B42-1 (NE) - B42-2 (NE-)
    Cold
    835 to 1,400 Ω
    B42-1 (NE) - B42-2 (NE-)
    Hot
    1,060 to 1,645 Ω

    HINT:
    In the table above, the terms "Cold" and "Hot" refer to the temperature of the coils in the sensor. "Cold" means approximately -10 to 50°C (14 to 122°F). "Hot" means approximately 50 to 100°C (122 to 212°F).

  1. Reconnect the crankshaft position sensor connector.



NG
REPLACE CRANKSHAFT POSITION SENSOR
OK


2. CHECK WIRE HARNESS (CRANKSHAFT POSITION SENSOR - ECM)

  1. A128656E01
    Disconnect the B42 crankshaft position sensor connector.

  1. Disconnect the B32 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B42-1 (NE) - B32-78 (NE+)
    Below 1 Ω
    B42-2 (NE-) - B32-77 (NE-)
    Below 1 Ω
    B42-1 (NE) or B32-78 (NE+) - Body ground
    10 kΩ or higher
    B42-2 (NE-) or B32-77 (NE-) - Body ground
    10 kΩ or higher

  1. Reconnect the crankshaft position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3. CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION)

  1. BR03795E15
    Check the sensor installation.

    OK:
    Sensor is installed correctly.



NG
REPAIR OR REPLACE CRANKSHAFT POSITION SENSOR
OK


4. CHECK CRANKSHAFT TIMING SPROCKET
  1. Check the teeth of the crankshaft timing sprocket.

    OK:
    The sensor plate's teeth do not have any cracks or deformation.



NG
REPLACE CRANKSHAFT TIMING SPROCKET
OK

REPLACE ECM


← P0335 Crankshaft Position Sensor "A" Circuit (+ P0339) (Nov 2005 – Dec 2006)P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor) (Nov 2005 – Dec 2006) →