2005-2008 RAV4 · Service Manual ENGINE

P0110 Intake Air Temperature Circuit

Diagnostic trouble codes · Vehicles built from Aug 2007

Also covers:

Versions by build date: Jan 2007 – Jul 2007 from Aug 2007

DESCRIPTION

The intake air temperature sensor is built into the mass air flow meter and senses the intake air temperature.
G036559E03
A thermistor built in the sensor changes its resistance value according to the intake air temperature.
The lower the intake air temperature, the greater the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (see Fig. 1).
The intake air temperature sensor is connected to the ECM.
The 5 V power source voltage in the ECM is applied to the intake air temperature sensor from terminal THA via resistor R.
The resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes in accordance with changes in the intake air temperature, the potential at terminal THA also changes. Based on this signal, the ECM increases the fuel injection volume to improve driveability with a cold engine.
DTC No.
DTC Detection Condition
Trouble Area
P0110
Open or short in intake air temperature (IAT) sensor circuit for 0.5 seconds
(1 trip detection logic)
  1. Open or short in intake air temperature (IAT) sensor circuit
  2. IAT sensor (built into mass air flow meter)
  3. ECM
P0112
Short in IAT sensor circuit for 0.5 seconds
(1 trip detection logic)
  1. Open or short in IAT sensor circuit
  2. IAT sensor (built into mass air flow meter)
  3. ECM
P0113
Open in IAT sensor circuit for 0.5 seconds
(1 trip detection logic)
  1. Open or short in IAT sensor circuit
  2. IAT sensor (built into mass air flow meter)
  3. ECM

HINT:
When DTC P0110, P0112, or P0113 is detected, check the intake air temperature by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / Intake Air.
Reference: 
Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
140°C (284°F) or more
Short circuit


WIRING DIAGRAM

A112566E06

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
If DTCs relating to different systems are output, and they share terminal E2 as their ground, check this ground circuit first.


1. READ VALUE USING MASS AIR FLOW METER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value.

    Standard value:
    Same value as the actual air temperature.

    Result:
    Temperature Displayed
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F) or more
    B
    OK (same as air temperature near intake manifold)
    C

    HINT:
    1. If there is an open circuit, the tester indicates -40°C (-40°F).
    2. If there is a short circuit, the tester indicates 140°C (284°F) or more.



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS
A


2. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

  1. A131556E04
    Disconnect the mass air flow meter connector.

  1. Connect terminals THA and E2 of the mass air flow meter wire harness side connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value.

    Standard value:
    140°C (284°F) or more

  1. Reconnect the mass air flow meter connector.



OK
CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER
NG


3. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

  1. A131548E14
    Disconnect the mass air flow meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B34-4 (THA) - B32-110 (THA)
    Below 1 Ω
    B34-5 (E2) - B32-87 (ETHA)
    Below 1 Ω

  1. Reconnect the mass air flow meter connector.

  1. Reconnect the ECM connector.



OK
REPAIR OR REPLACE HARNESS OR CONNECTOR
NG

CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER

4. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

  1. A131552E04
    Disconnect the mass air flow meter connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value.

    Standard value:
    -40°C (-40°F)

  1. Reconnect the mass air flow meter connector.



OK
REPLACE MASS AIR FLOW METER
NG


5. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

  1. A131548E15
    Disconnect the mass air flow meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B34-4 (THA) or B32-110 (THA) - Body ground
    10 kΩ or higher

  1. Reconnect the mass air flow meter connector.

  1. Reconnect the ECM connector.



OK
REPAIR OR REPLACE HARNESS OR CONNECTOR
NG

REPLACE ECM


← P0110 Intake Air Temperature Circuit (+ P0112, P0113) (Jan 2007 – Jul 2007)P0115 Engine Coolant Temperature Circuit (+ P0117, P0118) (Jan 2007 – Jul 2007) →