P0115 Engine Coolant Temperature Circuit
Diagnostic trouble codes · Vehicles built from Aug 2007
Also covers:
- P0117 Engine Coolant Temperature Circuit Low Input
- P0118 Engine Coolant Temperature Circuit High Input
Versions by build date: Jan 2007 – Jul 2007 from Aug 2007
DESCRIPTION
A thermistor is built into the Engine Coolant Temperature (ECT) sensor and it changes its resistance value according to the engine coolant temperature.The structure of the sensor and connection to the ECM is the same as the intake air temperature sensor.
- HINT:
- If the ECM detects the DTC P0115, P0117, or P0118, it operates the fail-safe function in which the ECT is assumed to be 80°C (176°F).
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0115 |
Open or short in engine coolant temperature (ECT) sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| P0117 |
Short in ECT sensor circuit for 0.5 seconds (sensor resistance value less than 79 Ω) (1 trip detection logic) |
|
| P0118 |
Open in ECT sensor circuit for 0.5 seconds (sensor resistance value more than 156 kΩ) (1 trip detection logic) |
|
- HINT:
- When DTC P0115, P0117, and/or P0118 is detected, check the engine coolant temperature by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / Coolant Temp.
Reference: Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
140°C (284°F) or more
Short circuit
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- If DTCs relating to different systems are output, and they share terminal E2 as their ground, check this ground circuit first.
| 1. READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT TEMPERATURE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the value.
- Standard value:
- Between 75 and 95°C (167 and 203°F) with warm engine.
- Result:
Temperature Displayed
Proceed to
-40°C (-40°F)
A
140°C (284°F) or more
B
Between 75 and 95°C (167 and 203°F)
C
- HINT:
- If there is an open circuit, the tester indicates -40°C (-40°F).
- If there is a short circuit, the tester indicates 140°C (284°F) or more.
- If there is an open circuit, the tester indicates -40°C (-40°F).
|
|
||||
|
|
||||
| A | |
| 2. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS) |
Disconnect the ECT sensor connector.

Connect terminals 1 and 2 of the ECT sensor wire harness side connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the value.
- Standard value:
- 140°C (284°F) or higher.
Reconnect the ECT sensor connector.
|
|
||||
| NG | |
| 3. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM) |
Disconnect the ECT sensor connector.

Disconnect the ECM connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
B4-2 - B32-111 (THW)
Below 1 Ω
B4-1 - B32-88 (ETHW)
Below 1 Ω
Reconnect the ECT sensor connector.
Reconnect the ECM connector.
|
|
||||
| NG | ||
| ||
| 4. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS) |
Disconnect the ECT sensor connector.

Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the value.
- Standard value:
- -40°C (-40°F) or more.
Reconnect the ECT sensor connector.
|
|
||||
| NG | |
| 5. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM) |
Disconnect the ECT sensor connector.

Disconnect the ECM connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
B4-2 or B32-111 (THW) - Body ground
10 kΩ or higher
Reconnect the ECT sensor connector.
Reconnect the ECM connector.
|
|
||||
| NG | ||
| ||
