P0405 Exhaust Gas Recirculation Sensor "A" Circuit Low
Diagnostic trouble codes · Vehicles built Nov 2005 – Dec 2006
Also covers:
- P0406 Exhaust Gas Recirculation Sensor "A" Circuit High
Versions by build date: Nov 2005 – Dec 2006 from Jan 2007
DESCRIPTION
The EGR valve position sensor is mounted on the EGR valve and used for detecting the lift amount of the valve. The lift amount detected by the sensor is provided to the ECM as feedback. The ECM then regulates the lift amount of the valve in accordance with engine running conditions.| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0405 |
EGR valve position sensor output voltage is less than 0.1 V for more than 5 seconds (1 trip detection logic) |
|
| P0406 |
EGR valve position sensor output voltage is more than 4.9 V for more than 5 seconds (1 trip detection logic) |
|
- HINT:
- After confirming DTCs P0405 and P0406, check the EGR valve opening angle condition by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / EGR Position.
- The result values below are for when the ignition switch is on (IG) (engine is stopped), or when the engine is fully warmed-up and idling.
- After confirming DTCs P0405 and P0406, check the EGR valve opening angle condition by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / EGR Position.
Result
Condition
Changes between 0.3 V and 4.2 V
Normal
Less than 0.1 V
P0405 (Low input voltage)
More than 4.9 V
P0406 (High input voltage)
MONITOR DESCRIPTION
When output voltage of the EGR valve position sensor deviates from the normal operating range of 0.1 to 4.9 V for more than 0.5 seconds, the ECM interprets this as a malfunction of the sensor circuit, and illuminates the MIL.

WIRING DIAGRAM
Refer to DTC P0400 (Click here).INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
| 1. CHECK EGR VALVE POSITION SENSOR POWER SOURCE |
Disconnect the B54 EGR valve position sensor connector.

Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Connection
Specified Condition
B54-3 (VC) - B54-2 (E2)
4.5 to 5.5 V
Reconnect the EGR valve position sensor connector.
|
|
||||
| OK | |
| 2. INSPECT EGR VALVE POSITION SENSOR |
![]() ![]() |
Disconnect the B54 EGR valve position sensor connector.
Measure the resistance of the EGR valve position sensor.
- Standard resistance:
Tester Connection
EGR Valve Condition
Condition
Specified Condition
B54-3 (VC)- B54-2 (E2)
-
20°C (68°F)
3.5 to 6.5 kΩ
B54-4 (EGLS) - B54-2 (E2)
Fully open
20°C (68°F)
3.9 kΩ
B54-4 (EGLS) - B54-2 (E2)
Fully closed
20°C (68°F)
1.0 kΩ
Reconnect the EGR valve position sensor connector.
|
|
||||
| OK | |
| 3. CHECK WIRE HARNESS (EGR VALVE POSITION SENSOR - ECM) |
Disconnect the B54 sensor connector.

Disconnect the B32 ECM connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
B54-3 (VC) - B32-72 (VCEG)
Below 1 Ω
B54-4 (EGLS) - B32-118 (EGLS)
Below 1 Ω
B54-2 (E2) - B32-95 (EEGL)
Below 1 Ω
B54-3 (VC) or B32-72 (VCEG) - Body ground
10 kΩ or higher
B54-4 (EGLS) or B32-118 (EGLS) - Body ground
10 kΩ or higher
Reconnect the EGR valve position sensor connector.
Reconnect the ECM connector.
|
|
||||
| OK | ||
| ||

