2005-2008 RAV4 · Service Manual ENGINE

P0095 Intake Air Temperature Sensor 2 Circuit

Diagnostic trouble codes · Vehicles built Nov 2005 – Dec 2006

Also covers:

Versions by build date: Nov 2005 – Dec 2006 from Jan 2007

DESCRIPTION

The diesel turbo Intake Air Temperature (IAT) sensor is built into the charge air cooler and senses the IAT. A built-in thermistor in the sensor changes its resistance value according to the intake air temperature. The lower the intake air temperature, the greater the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (see Fig. 1).
The sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the sensor from terminal THIA via resistor R. Resistor R and the sensor are connected in series. When the resistance value of the sensor changes in accordance with changes in the IAT, the potential at terminal THIA also changes. Based on this signal, the ECM corrects the fuel injection volume to improve driveability with a cold engine.
G036559E03
DTC No.
DTC Detection Condition
Trouble Area
P0095
Open or short in diesel turbo IAT sensor circuit for 0.5 seconds
(1 trip detection logic)
  1. Open or short in diesel turbo IAT sensor circuit
  2. Diesel turbo IAT sensor
  3. ECM
P0097
Short in diesel turbo IAT sensor circuit for 0.5 seconds
(sensor resistance value less than 25 Ω [sensor output voltage less than 0.05 V])
(1 trip detection logic)
  1. Open or short in IAT sensor circuit
  2. Diesel turbo IAT sensor
  3. ECM
P0098
Open in diesel turbo IAT sensor circuit for 0.5 seconds
(sensor resistance value more than 156 kΩ [sensor output voltage more than 4.9 V])
(1 trip detection logic)
  1. Open or short in IAT sensor circuit
  2. Diesel turbo IAT sensor
  3. ECM

WIRING DIAGRAM

C129777E01

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
If DTCs relating to different systems are output, and they share terminal E2 as their ground, check this ground circuit first.


1. READ VALUE USING DIESEL TURBO INLET AIR TEMPERATURE SENSOR
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

  1. Read the value.

    Standard value:
    Same value as the actual intake air temperature.

    Result:
    Temperature Displayed
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F) or more
    B
    OK (same as air temperature near to intake manifold)
    C

    HINT:
    1. If there is an open circuit, the tester indicates -40°C (-40°F).
    2. If there is a short circuit, the tester indicates 140°C (284°F) or more.



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS
A


2. CHECK WIRE HARNESS (CHECK FOR OPEN IN WIRE HARNESS)

  1. A131551E01
    Disconnect the A49 diesel turbo IAT sensor connector.

  1. Connect terminals 1 and 2 of the diesel turbo IAT sensor wire harness side connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

  1. Read the value.

    Standard value:
    140°C (284°F) or more.

  1. Reconnect the diesel turbo IAT sensor connector.



OK
CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE DIESEL TURBO INTAKE AIR TEMPERATURE SENSOR
NG


3. CHECK WIRE HARNESS (DIESEL TURBO INLET AIR TEMPERATURE SENSOR - ECM)

  1. A128257E01
    Disconnect the A49 diesel turbo IAT sensor connector.

  1. Disconnect the B32 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A49-2 - B32-113 (THIA)
    Below 1 Ω
    A49-1 - B32-90 (ETHI)
    Below 1 Ω

  1. Reconnect the diesel turbo IAT sensor.

  1. Reconnect the ECM connector.



OK
REPAIR OR REPLACE HARNESS AND CONNECTOR
NG

CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

4. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

  1. A131552E01
    Disconnect the A49 diesel turbo IAT sensor connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

  1. Read the value.

    Standard value:
    -40°C (-40°F) or more.

  1. Reconnect the diesel turbo IAT sensor connector.



OK
REPLACE DIESEL TURBO INTAKE AIR TEMPERATURE SENSOR
NG


5. CHECK WIRE HARNESS (DIESEL TURBO INLET AIR TEMPERATURE SENSOR - ECM)

  1. A128257E02
    Disconnect the A49 diesel turbo IAT sensor connector.

  1. Disconnect the B32 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A49-2 or B32-113 (THIA) - Body ground
    10 KΩ or higher

  1. Reconnect the diesel turbo IAT sensor connector.

  1. Reconnect the ECM connector.



OK
REPAIR OR REPLACE HARNESS AND CONNECTOR
NG

REPLACE ECM


← P0093 Fuel System Leak Detected - Large Leak (from Jan 2007)P0095 Intake Air Temperature Sensor 2 Circuit (+ P0097, P0098) (from Jan 2007) →