2005-2008 RAV4 · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from Aug 2007


1. INSTALL INPUT SHAFT OIL SEAL RING

  1. D025587E01
    Compress a new input shaft oil seal ring from both sides to reduce dimension A.

    Dimension A:
    5.0 mm (0.197 in.)

  1. Coat the oil seal ring with ATF and install it to the forward clutch drum.

    NOTICE:
    Do not expand the end gap of the oil seal ring excessively. Securely engage the hooks.


2. INSTALL FORWARD CLUTCH PISTON SUB-ASSEMBLY

  1. D026707E02
    Coat the forward clutch piston with ATF, and install it to the forward clutch drum.

    NOTICE:
    Be careful not to damage the lip of the forward clutch piston.


3. INSTALL FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

  1. D026708E03
    Install the return spring to the forward clutch drum.

    NOTICE:
    After installing the spring, check that all of the springs fit in the piston correctly.

  1. Coat the clutch balancer with ATF.

  1. D026709E04
    Install the clutch balancer to the forward clutch drum.

    NOTICE:
    1. Be careful not to damage the lip of the forward clutch balancer.
    2. Make sure that the clutch balancer is not pinched and that there are no other defects on the lip.
    3. Apply sufficient ATF to the sealing lip before installation.

  1. D026418E02
    Place SST on the clutch balancer, and compress the clutch balancer with a press.
    SST
    09387-00020  

  1. Install the snap ring with a snap ring expander.

  1. Make sure that the end gap of the snap ring is not aligned with the spring retainer claw.

    NOTICE:
    1. Stop the press when the spring seat is lowered to a position 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove. This prevents the spring seat from being deformed.
    2. Do not expand the snap ring excessively.

  1. D026788E02
    Set the end gap of the snap ring in the piston as shown in the illustration.

    NOTICE:
    The end gap of the snap ring should not align with any of the stoppers.


4. INSTALL FORWARD MULTIPLE DISC CLUTCH DISC
  1. Coat the 5 discs with ATF.

  1. D026415E01
    Install the 5 plates, 5 discs and flange to the forward clutch drum.

    NOTICE:
    Make sure that the plates, discs, and flange are installed as shown in the illustration.

  1. D026753E01
    Using a screwdriver, install the snap ring.

  1. Check that the end gap of the snap ring is not aligned with one of the cutouts.

    NOTICE:
    The snap ring should be fully engaged in the groove of the drum.


5. INSPECT PACK CLEARANCE OF FORWARD CLUTCH

  1. D026715E01
    Using a dial indicator, measure the forward clutch pack clearance while applying and releasing compressed air (392 kgf/cm2, 4.0 kPa, 57 psi).

    Pack clearance:
    1.00 to 1.25 mm (0.0394 to 0.4921 in.)

    If the pack clearance is less than the minimum, parts may be assembled incorrectly. Check and reassemble the parts again.
    If the clearance is not as specified, select another flange.

    HINT:
    There are 5 different thicknesses of flanges available.

    Standard flange thickness:
    No.
    Thickness
    No.
    Thickness
    1
    3.00 mm (0.1181 in.)
    4
    3.45 mm (0.1358 in.)
    2
    3.15 mm (0.1240 in.)
    5
    3.60 mm (0.1417 in.)
    3
    3.30 mm (0.1299 in.)
    -
    -


6. INSPECT FORWARD MULTIPLE DISC CLUTCH DISC

  1. D003672E01
    Check if the disc lightly rotates when rotating the forward clutch after inserting the multiple disc clutch into it.

    NOTICE:
    Do not place the forward clutch in a vise.

← INSPECTION (from Aug 2007)COMPONENTS (from Aug 2007) →