2005-2008 RAV4 · Service Manual ENGINE

P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance

Diagnostic trouble codes · Vehicles built from Jan 2007

Versions by build date: Nov 2005 – Dec 2006 from Jan 2007

DESCRIPTION

HINT:
  1. This is the repair procedure for the accelerator pedal position sensor.
  2. This electrical throttle system does not use a throttle cable.
  3. This accelerator pedal position sensor is a non-contact type.

The accelerator pedal position sensor is mounted on the accelerator pedal and detects the opening angle of the accelerator pedal. Since this sensor is electronically controlled with Hall-effect elements, accurate control and reliability can be obtained. It has 2 sensors to detect both the accelerator position and a malfunction of the accelerator position sensor.
In the accelerator pedal position sensor, the voltage applied to pedal terminals VPA and VPA2 of the ECM changes between 0 V and 5 V in proportion to the opening angle of the accelerator pedal. The VPA is a signal to indicate the actual accelerator pedal opening angle which is used for the engine control, and the VPA2 is a signal to indicate the information about the opening angle which is used for detecting malfunctions. The ECM determines the current opening angle of the accelerator pedal using signals from terminals VPA and VPA2, and the ECM controls the throttle motor based on these signals.
A129363E01
DTC No.
DTC Detection Condition
Trouble Area
P2121
Condition (a) continues for 2 seconds:
(a) Difference between VPA1 and VPA2 exceeds the threshold
(1 trip detection logic)
  1. Accelerator pedal position sensor circuit
  2. Accelerator pedal position sensor
  3. ECM

WIRING DIAGRAM

Refer to DTC P2121 (Click here).

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).


1. READ VALUE USING ACCELERATOR PEDAL POSITION SENSOR

  1. C129061E02
    Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Position 1 and Accel Position 2.

  1. Read the values.

    Standard voltage:
    Accelerator Pedal
    Accel Position 1
    Accel Position 2
    Released
    0.6 to 1.0 V
    1.4 to 1.8 V
    Depressed
    3.4 to 3.8 V
    4.2 to 4.6 V



OK
REPLACE ECM
NG


2. CHECK WIRE HARNESS (ACCELERATOR PEDAL POSITION SENSOR - ECM)

  1. A128721E01
    Disconnect the A6 accelerator pedal position sensor connector.

  1. Disconnect the A12 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A6-1 (VCP2) - A12-56 (VCP2)
    Below 1 Ω
    A6-2 (EPA2) - A12-58 (EPA2)
    Below 1 Ω
    A6-3 (VPA2) - A12-54 (VPA2)
    Below 1 Ω
    A6-4 (VCPA) - A12-55 (VCPA)
    Below 1 Ω
    A6-5 (EPA) - A12-57 (EPA)
    Below 1 Ω
    A6-6 (VPA) - A12-53 (VPA)
    Below 1 Ω
    A6-1 (VCP2) or A12-56 (VCP2) - Body ground
    10 kΩ or higher
    A6-2 (EPA2) or A12-58 (EPA2) - Body ground
    10 kΩ or higher
    A6-3 (VPA2) or A12-54 (VPA2) - Body ground
    10 kΩ or higher
    A6-4 (VCPA) or A12-55 (VCPA) - Body ground
    10 kΩ or higher
    A6-5 (EPA) or A12-57 (EPA) - Body ground
    10 kΩ or higher
    A6-6 (VPA) or A12-53 (VPA) - Body ground
    10 kΩ or higher

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ACCELERATOR PEDAL ROD ASSEMBLY


← P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance (Nov 2005 – Dec 2006)P2226 Barometric Pressure Circuit (+ P2227, P2228, P2229) (Nov 2005 – Dec 2006) →