P2047 Reductant Injector Circuit / Open (Bank 1 Unit 1)
Diagnostic trouble codes · Vehicles built from Aug 2007
Also covers:
- P2048 Short to GND in Reductant Injector Circuit (Bank 1)
- P2049 Short to B+ in Reductant Injector Circuit (Bank 1)
Versions by build date: Jan 2007 – Jul 2007 from Aug 2007
DESCRIPTION


The exhaust fuel addition injector is mounted on the exhaust port of the cylinder head, and low pressure is provided to the injector by the feed pump in the supply pump. This injector adds fuel by a control signal from the ECM.
This injector is used for two different controls: Diesel Particulate Filter (DPF) catalyst regeneration and nitrogen oxide (NOx) reduction.
Under the DPF catalyst regeneration control, the injector adds fuel to raise a catalyst temperature.
In the other control, the injector helps the air-fuel ratio become RICH. As a result, NOx in the exhaust gas will be reduced in response to the RICH air-fuel ratio.
- HINT:
- For more information on the exhaust fuel addition injector and DPF, refer to the following procedures (Click here)
- If P2047, P2048 and P2049 are present, refer to the DTC table for Diesel Particulate Filter System (Click here).
- For more information on the exhaust fuel addition injector and DPF, refer to the following procedures (Click here)
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P2047 |
With the exhaust fuel addition injector off, the FIVM1 output is High and the FIVM2 output is Low for 3 seconds. (1 trip detection logic) |
|
| P2048 |
With the exhaust fuel addition injector off, the FIVM1 output is High and the FIVM2 output is High for 0.16 seconds. (1 trip detection logic) |
|
| P2049 |
With the exhaust fuel addition injector on, the FIVM1 output is Low and the FIVM2 output is Low for 7 or more times. (1 trip detection logic) |
- HINT:
- DTC P1386 (injector for exhaust fuel addition) will be present if there is an open malfunction in the exhaust fuel addition injector circuit.
MONITOR DESCRIPTION
In order to detect abnormality in the fuel addition injector, an internal CPU of the ECM monitors injection command (FIV) signals and injection confirmation (FIVM) signals. The FIV signal is sent from the CPU to the (exhaust) fuel addition injector via a drive circuit inside the ECM. The FIVM signal, which is originally output from the internal drive circuit of the ECM, is transmitted to the CPU via a monitor circuit. By receiving the FIVM signal, the ECM judges that the current has been applied to the (exhaust) fuel addition injector.This DTC will be set if the ECM judges that the number of signals of the FIV and the FIVM are inconsistent.


WIRING DIAGRAM
Refer to DTC P1386 (Click here).INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
| 1. INSPECT EXHAUST FUEL ADDITION INJECTOR (RESISTANCE) |
Inspect exhaust fuel addition injector (Click here).
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR - ECM) |
Disconnect the exhaust fuel addition injector connector.

Disconnect the ECM connector.
Check the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
B52-1 - B32-105 (FIV)
Below 1 Ω
B52-1 or B32-105 (FIV) - Body ground
10 kΩ or higher
Reconnect the exhaust fuel addition injector connector.
Reconnect the ECM connector.
|
|
||||
| OK | ||
| ||
