2005-2008 RAV4 · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built from Nov 2005


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


2. REMOVE REAR WIPER ARM ASSEMBLY

  1. B136376
    Widen each end of the cap 5 mm (0.19in).

  1. B136377
    Lift the both widened ends of the cap.

  1. B136378
    Rotate the cap. Fix the cap in place.

  1. B131464
    Remove the nut and arm and blade.


3. REMOVE BACK DOOR TRIM BOARD

  1. B129943
    Using a screwdriver, detach the 13 clips and remove the trim board.

    HINT:
    1. Tape the screwdriver tip before use.
    2. If the screwdriver cannot reach the clips, pull on the lower trim to remove it.

  1. Remove the 5 screws and the back door trim pocket.


4. REMOVE BACK DOOR CENTER GARNISH

  1. B129944
    Using a screwdriver, detach the 4 claws and 4 clips and remove the garnish.

    HINT:
    Tape the screwdriver tip before use.


5. REMOVE BACK DOOR SIDE GARNISH LH

  1. B129945
    Using a screwdriver, detach the 2 claws and 2 clips and remove the garnish.


6. REMOVE BACK DOOR SIDE GARNISH RH

HINT:
Use the same procedures described for the LH side.


7. REMOVE REAR WIPER MOTOR GROMMET

8. REMOVE REAR WIPER MOTOR ASSEMBLY

B131460
  1. Disconnect the connector.

  1. Remove the 3 bolts and wiper motor.


9. REMOVE REAR SPOILER

  1. B127943
    Remove the 3 bolts.

  1. B127944
    Remove the 3 clips and spoiler.

  1. Disconnect the center stop light connector and remove the rear spoiler.


10. REMOVE BACK WINDOW MOULDING LOWER

B130157E01
  1. Using a knife, cut off the moulding as shown in the illustration.

    NOTICE:
    Do not damage the body with the knife.

  1. Remove the remaining moulding.


11. REMOVE BACK WINDOW MOULDING OUTSIDE LH

B130156E01
  1. Using a knife, cut off the moulding as shown in the illustration.

    NOTICE:
    Do not damage the body with the knife.

  1. Remove the remaining moulding.


12. REMOVE BACK DOOR GLASS
  1. Disconnect the rear window defogger connector.

  1. B130158E01
    Apply protective tape to the outer surface of the vehicle body to prevent scratches.

    NOTICE:
    When separating the back door glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.

  1. From the interior, insert a piano wire between the vehicle body and back door glass as shown in the illustration.

  1. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

  1. B134603
    Place matchmarks over the glass and vehicle body on the locations indicated in the illustration.

    HINT:
    Matchmarks do not need to be placed if the glass is not going to be reused.

  1. Cut through the adhesive by pulling the piano wire around the back door glass.

    NOTICE:
    Leave as much adhesive on the vehicle body as possible when removing the back door glass.

  1. Using suction cups, remove the back door glass.


13. CLEAN BACK DOOR GLASS

BO04421E02
  1. Clean the outer edge of the back door glass with white gasoline.

    NOTICE:
    1. Do not touch the back door glass surface after cleaning it.
    2. Be careful not to damage the glass.
    3. Even if using new back door glass, clean the back door glass with white gasoline.


14. CLEAN VEHICLE BODY

B106081E02
  1. Using a scraper, remove the moulding and adhesive from the back door glass.

  1. Clean and shape the contact surface of the vehicle body.

    1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

      NOTICE:
      Be careful not to damage the vehicle body.

    2. Clean the contact surface of the vehicle body with cleaner.

      HINT:
      Even if all the adhesive has been removed, clean the vehicle body.

← COMPONENTS (from Nov 2005)INSTALLATION (from Nov 2005) →