INSTALLATION
Removal / installation · Vehicles built from Aug 2007
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007
| 1. INSTALL RADIATOR AND INTERCOOLER |
- NOTICE:
- When reusing the air hose or air tube, check that there is no damage and foreign objects. If necessary, clean it.
Align the intercooler with the radiator, and then install the intercooler to the radiator with the 4 bolts.

- Torque:
- 6.0 N*m{ 61 kgf*cm , 53 in.*lbf }
Install the No. 2 air tube to the intercooler and No. 3 air hose.
Install the bolt.
- Torque:
- 13 N*m{ 133 kgf*cm , 10 ft.*lbf }
Tighten the 2 clamps as shown in the illustration.

Install the No. 2 air hose to the intercooler. Tighten the clamp as shown in the illustration.

Install the radiator (with intercooler) to the vehicle.
Connect the No. 2 and No. 3 air hoses to the engine.
Tighten the 2 clamps as shown in the illustration.

| 2. CONNECT INLET RADIATOR HOSE |
![]() ![]() |
Connect the inlet radiator hose to the engine.
Position the clip as illustrated.

| 3. CONNECT OUTLET RADIATOR HOSE |
![]() ![]() |
Connect the outlet radiator hose to the engine.
Position the clip as illustrated.

| 4. INSTALL RADIATOR SUPPORT UPPER |
![]() ![]() |
Install the radiator support upper with the 4 bolts.
- Torque:
- 29 N*m{ 296 kgf*cm , 21 ft.*lbf }
| 5. INSTALL COOLER CONDENSER ASSEMBLY |
Install the cooler condenser.

| 6. INSTALL HOOD LOCK ASSEMBLY |
Install the hood lock striker with the 3 bolts.

- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
| 7. INSTALL NO. 1 WATER BY-PASS HOSE |
![]() ![]() |
Connect the No. 1 water by-pass hose to the radiator and radiator reservoir.
Position clips A and B as illustrated.

Install the No. 1 water by-pass hose with the 2 bolts to the radiator support upper.
- Torque:
- 5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
Attach the No. 1 water by-pass hose to the hose clamp.
| 8. INSTALL BATTERY BRACKET REINFORCEMENT |
Install the bracket reinforcement with the 2 bolts.

- Torque:
- 19 N*m{ 194 kgf*cm , 14 ft.*lbf }
| 9. INSTALL FRONT BATTERY BRACKET |
Install the front bracket with the 4 bolts.

- Torque:
- 19 N*m{ 194 kgf*cm , 14 ft.*lbf }
Attach the 2 wire harness clamps.
| 10. INSTALL BATTERY |
| 11. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY UPPER |
Install the reinforcement with the 8 bolts.

- Torque:
- 70 N*m{ 713 kgf*cm , 51 ft.*lbf }
Install the wire harness and attach the 5 claws.
| 12. INSTALL FRONT BUMPER |
Put protective tape under the front fender and headlight.

Install the 4 clips.
Install the hood cushion center.

w/ Headlight Cleaner:
Connect the headlight cleaner.
w/ Fog Light:
Connect the 2 fog light connectors.
Attach the 4 claws to install the bumper cover.

Install the 8 screws.

| 13. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
- Torque:
- 12.7 N*m{ 130 kgf*cm , 10 ft.*lbf }
Add TOYOTA Super Long Life Coolant (SLLC) to the radiator reservoir filler opening.
Continue adding TOYOTA SLLC until it is filled to the B line.

- HINT:
- The B line is the lower edge of the inner wall of the filler neck.
- Standard capacity:
Item
Specified Condition
w/o Combustion Type Power Heater
7.3 liters
(7.7 US qts, 6.4 Imp. qts)
w/ Combustion Type Power Heater
7.7 liters
(8.1 US qts, 6.8 Imp. qts)
- HINT:
- TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
- NOTICE:
- Never use water as a substitute for engine coolant.
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
Start the engine, and warm it up until the cooling fan operates.
Set the air conditioning as follows while warming up the engine.
Item
Specified Condition
Manual Air Conditioning System
Fan speed - Any setting except "OFF"
Temperature - Toward WARM
Air conditioning switch "OFF"
Automatic Air Conditioning System
Temperature - Toward MAX
Air conditioning switch "OFF"
Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.
- NOTICE:
- Make sure that the radiator reservoir still has some coolant in it.
- Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
- If there is not enough coolant, the engine may burn out or overheat.
- Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the B line.
- Until the coolant level has stabilized, run the engine at 2,000 rpm.
- Make sure that the radiator reservoir still has some coolant in it.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
- CAUTION:
- When pressing the radiator hoses:
- Wear protective gloves.
- Be careful as the radiator hoses are hot.
- Keep your hands away from the radiator fan.
- Wear protective gloves.
Stop the engine and wait until the coolant cools down to ambient temperature.
Check that the coolant level is between the FULL and LOW line.

If the coolant level is below the LOW line, repeat all of the procedures above.
If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW line.
| 14. CHECK FOR ENGINE COOLANT LEAKS |
Remove the radiator reservoir cap.
- CAUTION:
- To avoid the danger of being burned, do not remove the radiator reservoir cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.
Fill the radiator with coolant, and then attach a radiator cap tester.

Warm up the engine.
Pump the radiator cap tester to 137 kPa (1.4 kgf/cm2, 19 psi), and then check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leakage.
If there are no signs of external coolant leaks, check the heater core, cylinder block and head.
Reinstall the radiator cap.
| 15. INSTALL REAR ENGINE UNDER COVER LH |
Install the under cover with the 2 clips.
| 16. INSTALL REAR ENGINE UNDER COVER RH |
Install the under cover with the 2 clips.
| 17. INSTALL NO. 1 ENGINE UNDER COVER |
Install the engine under cover with the 12 clips and 4 bolts.
| 18. INSTALL NO. 1 ENGINE COVER |
Attach the 4 clips to install the engine cover.

| 19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 20. INSTALL RADIATOR SUPPORT OPENING COVER |
Install the 2 clips.

| 21. CHARGE WITH REFRIGERANT |
Perform vacuum purging using a vacuum pump.
Charge refrigerant HFC-134a (R134a).
- Standard:
- 430 +-30 g (15.2 +-1.1 oz.)
- SST
- 07110-58060
(07117-58060, 07117-58070, 07117-58080, 07117-58090, 07117-78050, 07117-88060, 07117-88070, 07117-88080)


- NOTICE:
- Do not operate the cooler compressor before charging refrigerant as the cooler compressor will not work properly without any refrigerant, and will overheat.
- Approximately 100 g (3.53 oz.) of refrigerant may need to be charged after bubbles disappear. The refrigerant amount should be checked by measuring its quantity, and not with the sight glass.
- Do not operate the cooler compressor before charging refrigerant as the cooler compressor will not work properly without any refrigerant, and will overheat.
| 22. WARM UP ENGINE |
Warm up the engine at less than 1,850 rpm for 2 minutes or more after charging the refrigerant.
- NOTICE:
- Be sure to warm up the compressor when turning the A/C switch ON after removing and installing the cooler refrigerant lines (including the compressor), to prevent damage to the compressor.
| 23. CHECK FOR REFRIGERANT LEAKAGE |
After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.
Perform the operation under these conditions:
- Stop the engine.
- Secure good ventilation (the gas leak detector may react to volatile gases other than refrigerant, such as evaporated gasoline or exhaust gas).
- Repeat the test 2 or 3 times.
- Make sure that some refrigerant remains in the refrigeration system. When compressor is off: approximately 392 to 588 kPa (4 to 6 kgf/cm2, 57 to 85 psi)
- Stop the engine.
Using a gas leak detector, check the refrigerant line for leakage.

If a gas leak is not detected on the drain hose, remove the blower motor control (blower resistor) from the cooling unit. Insert the gas leak detector sensor into the unit and perform the test.
Disconnect the connector and leave the pressure switch on for approximately 20 minutes. Bring the gas leak detector close to the pressure switch and perform the test.




