REMOVAL
Removal / installation · Vehicles built Jan 2007 – Jul 2007
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
| 2. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM |
Start up the engine.
Turn the A/C switch ON.
Operate the cooler compressor with an engine speed of approximately 1,000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the compressor oil remaining in each component into the cooler compressor.
Stop the engine.
Using SST, discharge the refrigerant gas.
- SST
- 07110-58060
(07117-58060, 07117-58070, 07117-58080, 07117-58090, 07117-78050, 07117-88060, 07117-88070, 07117-88080)
| 3. REMOVE RADIATOR SUPPORT OPENING COVER |
Remove the 2 clips.

Partially remove the radiator support opening cover.
- HINT:
- It is not necessary to fully remove the radiator support opening cover. Partially remove it so that the bumper cover can be removed later.
| 4. REMOVE NO. 1 ENGINE COVER |
Detach the 4 clips and remove the engine cover.

| 5. REMOVE NO. 1 ENGINE UNDER COVER |
Remove the 4 bolts, 12 clips and under cover.
| 6. REMOVE REAR ENGINE UNDER COVER LH |
Remove the 2 clips and under cover.
| 7. REMOVE REAR ENGINE UNDER COVER RH |
Remove the 2 clips and under cover.
| 8. DRAIN ENGINE COOLANT |
Loosen the radiator drain cock plug.
- HINT:
- Collect the coolant in a container and dispose of it according to the regulations in your area.
Remove the radiator reservoir cap.
- CAUTION:
- Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
Loosen the cylinder block drain cock plug.


| 9. REMOVE FRONT BUMPER |
Remove the 8 screws.

Apply protective tape under the front fender and headlight.

Using a screwdriver, detach the 4 claws.
- HINT:
- Tape the screwdriver tip before use.
w/ Fog Light:
Disconnect the 2 fog light connectors.
w/ Headlight Cleaner:
Disconnect the headlight cleaner.
Using a clip remover, remove the hood cushion center.

Using a clip remover, remove the 4 clips and front bumper cover.

| 10. REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY UPPER |
Disconnect the 2 horn connectors.
Remove the 2 bolts and reinforcement.
| 11. REMOVE BATTERY |
| 12. REMOVE FRONT BATTERY BRACKET |
Detach the 2 wire harness clamps.

Remove the 4 bolts and front bracket.
| 13. REMOVE BATTERY BRACKET REINFORCEMENT |
Remove the 2 bolts and bracket reinforcement.

| 14. REMOVE NO. 1 WATER BY-PASS HOSE |
![]() ![]() |
Detach the No. 1 water by-pass hose from the hose clamp.
Disconnect the No. 1 water by-pass hose from the radiator reservoir and radiator.
Remove the 2 bolts and No. 1 water by-pass hose.
| 15. REMOVE HOOD LOCK ASSEMBLY |
Remove the 3 bolts and hood lock striker.

| 16. REMOVE COOLER CONDENSER ASSEMBLY |
Remove the cooler condenser.

| 17. REMOVE RADIATOR SUPPORT UPPER |
![]() ![]() |
Remove the 4 bolts and radiator support upper.
| 18. DISCONNECT INLET RADIATOR HOSE |
![]() ![]() |
Remove the inlet radiator hose and No. 5 water by-pass hose from the radiator.
| 19. DISCONNECT OUTLET RADIATOR HOSE |
![]() ![]() |
Remove the outlet radiator hose from the radiator.
| 20. REMOVE RADIATOR AND INTERCOOLER |
Loosen the 2 clamps.

Disconnect the No. 2 and No. 3 air hoses from the engine.
Remove the radiator (with intercooler) from the vehicle.
Loosen the 2 clamps.

Remove the bolt.
Remove the No. 2 air tube from the intercooler and No. 3 air hose.
Loosen the clamp. Remove the No. 2 air hose from the intercooler.

Remove the 4 bolts, and then separate the intercooler and radiator.





