2005-2008 RAV4 · Service Manual ENGINE

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. REMOVE CAMSHAFT POSITION SENSOR

  1. A115775
    Disconnect the sensor connector.

  1. Remove the bolt and sensor.


2. REMOVE CRANKSHAFT POSITION SENSOR

  1. A133148
    Disconnect the sensor connector.

  1. Disconnect the sensor connector from the bracket.

  1. Disconnect the sensor wire harness clamp.

  1. Remove the bolt and sensor.


3. REMOVE OIL FILLER CAP

4. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
  1. Disconnect the ventilation hose.

  1. A134996
    Remove the 2 nuts, 2 washers, 13 bolts, 4 nozzle holder clamp seats and cylinder head cover.

  1. Remove the cylinder head cover gasket and cylinder head cover No. 2 gasket.


5. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

  1. A123530
    Remove the 18 bolts and 2 nuts.

  1. Z004119E01
    Insert the blade of SST between the oil pan and cylinder block, cut through the applied sealer and remove the oil pan.

    NOTICE:
    1. Do not use SST for the timing belt case side and rear oil seal retainer.
    2. Be careful not to damage the contact surfaces of the oil pan.

  1. Remove the gasket and drain plug.


6. REMOVE OIL FILTER CAP ASSEMBLY

  1. A123520
    Remove the clip and open the oil filter element service cover.

  1. A115207E04
    Remove the oil filter drain plug and O-ring, and then insert the drain pipe into the oil filter cap and drain the engine oil into a container.

    HINT:
    The drain pipe is supplied with the oil filter element.

  1. A123523E01
    Using SST, remove the oil filter cap together with the oil filter element.
    SST
    09228-06501  


7. REMOVE OIL FILTER ELEMENT

  1. A115233E03
    Remove the oil filter element and 2 O-rings from the oil filter cap.

    NOTICE:
    Be sure to remove the O-ring (for the cap) by hand, without using any tools, to prevent damage to the groove for the O-ring on the cap.


8. REMOVE OIL FILTER BRACKET

  1. A111390
    Remove the 4 bolts, oil filter bracket and gasket.


9. REMOVE OIL STRAINER SUB-ASSEMBLY

  1. A111262
    Remove the 3 bolts, oil strainer and O-ring.


10. REMOVE CRANKSHAFT PULLEY

  1. Set the No. 1 piston to the TDC/compression.

    1. A111192E02
      Turn the crankshaft pulley clockwise to align the timing pointer of the timing chain cover and timing mark on the pulley.

  1. A111193E02
    Make sure that the timing mark of the camshaft sprocket is at the top.

    HINT:
    If the timing mark is not at the top, turn the crankshaft pulley 1 revolution so that the timing mark comes to the top (Set the No. 1 piston to the TDC/compression).

  1. Put a matchmark on the timing chain plate that is aligned with the matchmark of the cam sprocket.

    HINT:
    The timing chain has 2 yellow-colored plates. If either of them is aligned with the matchmarks of the cam sprocket, this step can be omitted.

  1. A111194E06
    Turn the crankshaft by approximately 90° in the engine revolution direction at the point where the No. 1 piston is set to the TDC/compression so that the lifted valve and piston do not contact each other when removing the camshaft.

  1. A111238E01
    Using SST, remove the pulley bolt.
    SST
    09213-58013  
    09330-00021  

  1. Insert the service bolt.

    Recommended service bolt:
    Item
    Specified Condition
    Thread diameter
    22 mm (0.87 in.)
    Thread pitch
    1.5 mm (0.059 in.)
    Bolt length
    Approx. 30 to 38 mm (1.18 to 1.50 in.)

  1. A111239E01
    Using SST, remove the crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)


11. REMOVE WATER PUMP ASSEMBLY

  1. A111263
    Remove the 7 bolts, water pump and gasket.


12. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY (w/ Oil Pump)

  1. A111265E02
    Using a 10 mm socket hexagon wrench, remove the timing chain cover tight plug and gasket.

  1. A127989
    Remove the 13 bolts and seal washer as shown in the illustration.

  1. A111267E02
    Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Do not damage the contact surfaces of the cylinder head, cylinder block and timing chain cover.

  1. A111268
    Remove the gasket and O-ring.


13. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

  1. A101303E04
    Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner (*1).

  1. Move the stopper plate downward to set the lock, and insert SST into the stopper plate hole (*2).

    SST
    09240-00020   (09242-00200)

  1. A111270
    Remove the 2 bolts and chain tensioner.


14. REMOVE CHAIN TENSIONER SLIPPER

A111271E01

15. REMOVE NO. 1 CHAIN VIBRATION DAMPER

  1. A111272E01
    Remove the 2 bolts and vibration damper.


16. REMOVE CAMSHAFT TIMING SPROCKET

  1. A123590
    Remove the 4 bolts on the sprocket while holding the hexagonal portion of the No. 2 camshaft.

  1. Remove the camshaft timing sprocket, crankshaft timing sprocket and chain.


17. REMOVE CAMSHAFT

  1. A117173
    Using the crankshaft pulley bolt, set the No. 1 cylinder to 90° BTDC/compression.

  1. A111204E08
    Remove the 2 union bolts.

  1. Using several steps, loosen and remove the 20 bearing cap bolts uniformly in the sequence shown in the illustration.

  1. Remove the 8 bearing caps, No. 1 bearing cap and 2 oil delivery pipes.

    HINT:
    Do not remove the No. 4 bearing cap.

  1. Remove the camshaft and No. 2 camshaft.

  1. A111277E01
    Remove the No. 2 bearing cap.


18. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

  1. A111278
    Remove the 16 valve rocker arm.


19. REMOVE VALVE LASH ADJUSTER ASSEMBLY

  1. A111279
    Remove the valve lash adjusters from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.


20. REMOVE CYLINDER HEAD SUB-ASSEMBLY

  1. A111280
    Uniformly loosen the 10 bolts in the sequence shown in the illustration. Remove the 10 cylinder head bolts and plate washers.

    NOTICE:
    1. Do not drop washers into the cylinder head.
    2. Head warpage or cracking could result from removing bolts in the incorrect order.

  1. Remove the cylinder head and gasket.


21. REMOVE INTAKE VALVE

  1. A111290E03
    Using SST and wooden blocks, compress the compression spring and remove the valve retainer locks.
    SST
    09202-70020  

  1. Remove the retainer, compression spring and valve.

    HINT:
    Arrange the removed parts in the correct order.


22. REMOVE EXHAUST VALVE

  1. A111289E03
    Using SST and wooden blocks, compress the compression spring and remove the valve retainer locks.
    SST
    09202-70020  

  1. Remove the retainer, compression spring and valve.

    HINT:
    Arrange the removed parts in the correct order.


23. REMOVE VALVE STEM OIL SEAL

  1. A111291
    Using needle-nose pliers, remove the oil seal.


24. REMOVE VALVE SPRING SEAT

  1. A111292
    Using compressed air and a magnetic finger, remove the valve spring seat by blowing air onto it.


25. INSPECT ENGINE BALANCER ASSEMBLY THRUST CLEARANCE

  1. A123553
    Using a dial indicator, measure the thrust clearance while moving the balance shaft back and forth.

    Standard thrust clearance:
    0.09 mm (0.0035 in.)

    Maximum thrust clearance:
    0.11 mm (0.0043 in.)

    If the thrust clearance is greater than the maximum, replace the balance shaft.


26. REMOVE ENGINE BALANCER ASSEMBLY

  1. A111301E03
    Align the drive and driven gear's timing marks (1 dot mark each) by turning the crankshaft with a wrench.

  1. Install the service bolt.

    Recommended service bolt:
    Item
    Specified Condition
    Thread diameter
    6 mm (0.24 in.)
    Thread pitch
    1 mm (0.04 in.)
    Bolt length
    16 to 18 mm (0.63 to 0.71 in.)

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf }

    HINT:
    When removing the balancer, make certain that the torsional spring force of the sub gear has been eliminated by installation of the service bolt.

  1. A111302E02
    Remove the 2 bolts and oil baffle plate (*1).

  1. Uniformly loosen the 8 bolts in several steps, in the sequence shown in the illustration.

  1. Remove the engine balancer.


27. INSPECT CONNECTING ROD THRUST CLEARANCE

  1. A123591
    Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

    Standard thrust clearance:
    0.10 to 0.45 mm (0.0039 to 0.0177 in.)

    Maximum thrust clearance:
    0.55 mm (0.0217 in.)

    If the thrust clearance is greater than the maximum, replace one or more connecting rod as necessary. If necessary, replace the crankshaft.


28. INSPECT CONNECTING ROD OIL CLEARANCE

  1. A111305E02
    Check that the front marks on the connecting rod and cap are aligned to ensure the correct reassembly.

    NOTICE:
    The front marks on the connecting rods and caps are for ensuring the correct reassembly.

  1. Remove the 2 connecting rod cap bolts.

  1. A133123
    Using the 2 removed connecting rod cap bolts, remove the connecting rod cap and lower bearing by wiggling the connecting rod cap right and left.

    HINT:
    Keep the lower bearing inserted to the connecting rod cap.

  1. Clean the crank pin and bearing.

  1. Check the crank pin and bearing for pitting and scratches.

  1. A111306E02
    Lay a strip of Plastigage on the crank pin.

  1. A111307E02
    Check that the front mark of the connecting rod cap is facing forward.

  1. A111308E01
    Install and alternately tighten the bolts of the connecting rod cap in several steps.

    NOTICE:
    Do not turn the crankshaft.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. A101478E06
    Mark the front side of each connecting cap bolt with paint.

  1. Retighten the cap bolts by 90° as shown.

  1. Check that the painted mark is now at a 90° angle to the front.

    NOTICE:
    Do not turn the crankshaft.

  1. A111305E01
    Remove the 2 connecting rod cap bolts.

  1. Using the 2 removed connecting rod cap bolts, remove the connecting rod cap and lower bearing by wiggling the connecting rod cap right and left.

    HINT:
    Keep the lower bearing inserted to the connecting rod cap.

  1. A117179E03
    Measure the Plastigage at its widest point.

    Standard oil clearance:
    0.024 to 0.042 mm (0.0009 to 0.0017 in.)

    Maximum oil clearance:
    0.070 mm (0.0027 in.)

    If the oil clearance is greater than the maximum, replace the bearings. If necessary, grind or replace the crankshaft.

    HINT:
    If using a standard bearing, replace it with one that has the same number. If the number of the bearing cannot be determined, select the correct bearing by adding together the numbers imprinted on the crankshaft and connecting rod, then selecting the bearing with the same number as the total. There are 5 sizes of standard bearings, marked 1, 2, 3, 4 and 5.

    EXAMPLE:
    Connecting rod cap "3" + Crankshaft "1" = Total number 4 (Use bearing "4")

    Reference:
    Connecting rod big end inside diameter:
    Mark
    Thickness
    1
    53.000 to 53.006 mm (2.0866 to 2.0869 in.)
    2
    53.006 to 53.012 mm (2.0869 to 2.0871 in.)
    3
    53.012 to 53.018 mm (2.0871 to 2.0873 in.)
    Crankshaft pin diameter:
    Mark
    Thickness
    0
    49.994 to 50.000 mm (1.9683 to 1.9685 in.)
    1
    49.988 to 49.994 mm (1.9680 to 1.9683 in.)
    2
    49.982 to 49.988 mm (1.9678 to 1.9680 in.)
    Standard sized bearing center wall thickness:
    Mark
    Thickness
    1
    1.485 to 1.488 mm (0.0585 to 0.0586 in.)
    2
    1.488 to 1.491 mm (0.0586 to 0.0587 in.)
    3
    1.491 to 1.494 mm (0.0587 to 0.0588 in.)
    4
    1.494 to 1.497 mm (0.0588 to 0.0589 in.)
    5
    1.497 to 1.500 mm (0.0589 to 0.0591 in.)

  1. Completely remove the Plastigage.


29. REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD

  1. A111310E03
    Using a ridge reamer, remove all the carbon from the top of the cylinder.

  1. Push the piston, connecting rod assembly and upper bearing through the top of the cylinder block.

    HINT:
    1. Keep the bearing, connecting rod and cap together.
    2. Arrange the piston and connecting rod assemblies in the correct order.


30. REMOVE CONNECTING ROD BEARING

HINT:
Arrange the removed parts in the correct order.


31. INSPECT CRANKSHAFT THRUST CLEARANCE

  1. A123592
    Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

    Standard thrust clearance:
    0.04 to 0.24 mm (0.0016 to 0.0094 in.)

    Maximum thrust clearance:
    0.30 mm (0.0118 in.)

    If the thrust clearance is greater than the maximum, replace the thrust washers as a set. If necessary, replace the crankshaft.

    Standard thrust washer thickness:
    1.93 to 1.98 mm (0.0760 to 0.0780 in.)


32. REMOVE CRANKSHAFT AND CRANKSHAFT OIL CLEARANCE

  1. A111313E01
    Uniformly loosen the 10 bolts in several steps, in the sequence shown in the illustration.

  1. A111314E01
    Uniformly loosen the 10 bearing cap bolts in several steps, in the sequence shown in the illustration.

  1. A111340E04
    Remove the crankshaft bearing cap by prying between the crankshaft bearing cap and cylinder block with a screwdriver.

    NOTICE:
    Do not damage the contact surfaces of the cylinder block and crankshaft bearing cap.

    HINT:
    1. Keep the lower bearings and crankshaft bearing caps together.
    2. Arrange the thrust washers in the correct order.
    3. Keep the upper crankshaft bearings and upper thrust washers together with the cylinder block.
    4. Tape the screwdriver tip before use.

  1. Clean each main journal and bearing.

  1. Check each main journal and bearing for pitting and scratches.

    HINT:
    If the journal or bearing is damaged, replace the bearing.

  1. Place the crankshaft on the cylinder block.

  1. A111339E02
    Lay a strip of Plastigage across each journal.

  1. Place the crankshaft bearing cap assembly on the cylinder block.

  1. Install the crankshaft bearing cap bolts.

    HINT:
    The main bearing cap bolts are tightened in 2 progressive steps.

  1. Step 1

    1. A111315E01
      Install and uniformly tighten the 10 main bearing cap bolts in the sequence shown in the illustration.

      Torque:
      60 N*m{ 612 kgf*cm , 44 ft.*lbf }

      HINT:
      If any of the main bearing cap bolts does not meet the torque specification, replace the main bearing cap bolt.

      NOTICE:
      Do not turn the crankshaft.

  1. Step 2

    1. Mark the front of the bearing cap bolts with paint.

    2. A101478E06
      Retighten the bearing cap bolts by 90° as shown.

    3. Check that the painted mark is now at a 90° angle to the front.

  1. A111316E01
    Install and uniformly tighten the 10 bolts, in several passes in the sequence shown.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Remove the crankshaft bearing cap.

  1. A117181E03
    Measure the Plastigage at its widest point.

    Standard oil clearance:
    Bearing Cap
    Specified Condition
    No. 3
    0.020 to 0.038 mm (0.00079 to 0.00149 in.)
    Others
    0.014 to 0.032 mm (0.00055 to 0.00126 in.)

    Maximum oil clearance:
    0.10 mm (0.0039 in.)

    If the oil clearance is greater than the maximum, replace the bearings. If necessary, grind or replace the crankshaft.

    HINT:
    If using a standard bearing, replace it with one having the same number. If the number of the bearing cannot be determined, select the correct bearing by adding together the numbers imprinted on the cylinder block and crankshaft, then selecting the bearing with the same number as the total.
    There are 5 sizes of standard bearings, marked 0, 1, 2, 3 and 4.

    EXAMPLE:
    Cylinder block "2" + Crankshaft "1" = Total number 3 (Use bearing "3")

    Reference:
    Standard cylinder block main journal bore diameter:
    Mark
    Specified Condition
    0 (No. 3 Journal)
    63.000 to 63.006 mm (2.48031 to 2.48055 in.)
    1 (No. 3 Journal)
    63.006 to 63.012 mm (2.48055 to 2.48078 in.)
    2 (No. 3 Journal)
    63.012 to 63.018 mm (2.48078 to 2.48102 in.)
    1 (Others)
    63.000 to 63.006 mm (2.48031 to 2.48055 in.)
    2 (Others)
    63.006 to 63.012 mm (2.48055 to 2.48078 in.)
    3 (Others)
    63.012 to 63.018 mm (2.48078 to 2.48102 in.)
    Standard crankshaft journal diameter:
    Mark
    Specified Condition
    0
    58.994 to 59.000 mm (2.32259 to 2.32283 in.)
    1
    58.988 to 58.994 mm (2.32236 to 2.32259 in.)
    2
    58.982 to 58.988 mm (2.32212 to 2.32236 in.)
    Standard sized bearing center wall thickness:
    Mark
    Specified Condition
    0
    1.987 to 1.990 mm (0.07823 to 0.07835 in.)
    1
    1.990 to 1.993 mm (0.07835 to 0.07846 in.)
    2
    1.993 to 1.996 mm (0.07846 to 0.07858 in.)
    3
    1.996 to 1.999 mm (0.07858 to 0.07870 in.)
    4
    1.999 to 2.002 mm (0.07870 to 0.07881 in.)
    5
    2.002 to 2.005 mm (0.07881 to 0.07894 in.)

  1. Completely remove the Plastigage.

  1. Lift out the crankshaft.

  1. A111317E01
    Remove the upper bearings and upper thrust washers from the cylinder block.

    HINT:
    Arrange the bearings and thrust washers in the correct order.


33. REMOVE NO. 2 CRANKSHAFT BEARING
  1. Remove the lower bearings from the crankshaft bearing cap.

    HINT:
    Arrange the bearings in the correct order.


34. REMOVE ENGINE REAR OIL SEAL
  1. Remove the rear oil seal from the crankshaft.


35. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

  1. A111318E01
    Using a T30 "torx" socket wrench, remove the 3 bolts and crankshaft position sensor plate.


36. REMOVE PISTON RING SET

HINT:
Arrange the piston rings in the correct order.

  1. A111311
    Using a piston ring expander, remove the 2 compression rings.

  1. Using a piston ring expander, remove the oil ring rail.

  1. Remove the oil ring expander by hand.


37. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

  1. A117180
    Remove the water drain cock from the cylinder block.

  1. Remove the water drain cock plug from the water drain cock.


38. REMOVE PISTON WITH PIN SUB-ASSEMBLY

  1. A111362
    Check the fitting condition between the piston and piston pin.

    1. Try to move the piston back and forth on the piston pin.

      HINT:
      If any movement is felt, replace the piston and pin as a set.

  1. A111320E03
    Disconnect the connecting rod from the piston.

    1. Using a screwdriver, pry off the snap rings from the piston.

    2. A100988
      Gradually heat the piston to approximately 80 to 90°C (176 to 194°F).

    3. G036556E01
      Using a brass bar and plastic-faced hammer, lightly tap out the piston pin and remove the connecting rod.

      HINT:
      1. The piston and pin are a matched set.
      2. Arrange the pistons, pins, rings, connecting rods and bearings in the correct order.


39. REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

  1. A111324E01
    Using a 5 mm hexagon wrench, remove the oil nozzles.


40. REMOVE OIL REFLECTOR PLATE

  1. A111325E01
    Using a 5 mm hexagon wrench, remove the reflector plate.

← DISASSEMBLY (Jan 2007 – Jul 2007)INSPECTION (Nov 2005 – Dec 2006) →