2005-2008 RAV4 · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built Nov 2005 – Dec 2006

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

  1. A111350E02
    Apply adhesive around the drain cock.

    Seal packing:
    Toyota genuine seal packing 1282B, three bond 1282B or equivalent

  1. Install the cylinder block water drain cock.

    1. Temporarily install the cock.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    2. A111319E03
      Within one full rotation, tighten the cock to the angle shown the illustration.

      Torque:
      80 N*m{ 816 kgf*cm , 59 ft.*lbf } or lower

      NOTICE:
      Do not loosen the cock to adjust it. If an adjustment is necessary, remove the cock and reinstall it.


2. INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

  1. A111318E03
    Install the sensor plate by fitting the straight pin of the crankshaft into the hole on the sensor plate.

  1. Using a T30 "torx" socket wrench, install the 3 bolts.

    Torque:
    10.5 N*m{ 107 kgf*cm , 8 ft.*lbf }

    NOTICE:
    Make sure confirm that the sensor plate is not slanted.


3. INSTALL OIL REFLECTOR PLATE

  1. A111326E01
    Using a 5 mm hexagon wrench, install the oil reflector plates.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


4. INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

  1. A111324E02
    Using a 5 mm hexagon wrench, install the oil nozzles.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


5. INSTALL PISTON WITH PIN SUB-ASSEMBLY

  1. A117784E02
    Assemble the piston and connecting rod.

    1. Using a screwdriver, install a new snap ring at one end of the piston pin hole.

    2. A111360
      Gradually heat the piston to approximately 80 to 90°C (176 to 194°F).

    3. Coat the piston pin with engine oil.

    4. A111361E01
      Align the front marks of the piston and connecting rod, and push in the piston pin with your thumb.

      HINT:
      The piston and pin are a matched set.

    5. A111362E01
      Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.

    6. A111320E04
      Using a screwdriver, install a new snap ring at the other end of the piston pin hole.


6. INSTALL PISTON RING SET

  1. A111363E01
    Install the oil ring expander by hand.

  1. A111364E02
    Using a piston ring expander, install the oil ring rail.

  1. G038405E02
    Using a piston ring expander, install the 2 compression rings so that the painted marks are positioned as shown in the illustration.

    HINT:
    1. Install the No. 1 compression ring with the code mark (1T) facing upward.
    2. Install the No. 2 compression ring with the code mark (2FTE) facing upward.

  1. A111366E05
    Position the piston rings so that the ring ends are as shown in the illustration.

    NOTICE:
    Do not align the ring ends.


7. INSTALL NO. 2 CRANKSHAFT BEARING

NOTICE:
  1. Do not apply engine oil to the bearing's contact area and backside.

  1. Clean the main journal, and the both surfaces of the bearing.

  1. A111367E03
    Align the bearing claw with the claw groove of the crankshaft bearing cap, and push in the 5 lower bearings.


8. INSTALL CRANKSHAFT BEARING

NOTICE:
Do not apply engine oil to the bearing's contact area and backside.

  1. Clean the main journal, and the both surfaces of the bearing.

  1. A101023
    Align the bearing claw groove of the cylinder block, and push in the 5 upper bearings.


9. INSTALL CRANKSHAFT UPPER THRUST WASHER
  1. Apply engine oil to the crankshaft bearings, then place the crankshaft on the cylinder block.

  1. A111365
    Install the 2 thrust washers to the No. 4 journal position of the cylinder block.

  1. Push the crankshaft toward the front (rear) side.

  1. Check the 2 thrust washers with the oil grooves facing outward.


10. INSTALL CRANKSHAFT

  1. A111382E03
    Apply seal packing in a continuous bead as shown in the illustration.

    Seal packing:
    Toyota genuine seal packing block, three bond 1207B or equivalent

    Seal diameter:
    2.0 to 4.0 mm (0.078 to 0.157 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the crankcase within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 4 hours after installing.
    4. Do not overlap seal packing in area ● in the illustration.
    5. Do not apply seal packing in groove C.

  1. Apply engine oil to the crankshaft No. 2 bearings, then place the crankshaft bearing cap on the cylinder block.

  1. Install the crankshaft bearing cap bolts.

    HINT:
    The main bearing cap bolts are tightened in 2 progressive steps.

  1. A111315E01
    Step 1

    1. Install and uniformly tighten the 10 main bearing cap bolts in the sequence shown in the illustration.

      Torque:
      60 N*m{ 612 kgf*cm , 44 ft.*lbf }

      HINT:
      If any of the main bearing cap bolts does not meet the torque specification, replace the main bearing cap bolt.

  1. A101478E06
    Step 2

    1. Mark the front of the bearing cap bolts with paint.

    2. Retighten the bearing cap bolts by 90° as shown.

    3. Check that the painted mark is now at a 90° angle to the front.

  1. Check that the crankshaft turns smoothly.

  1. A111316E01
    Install and uniformly tighten the 10 bolts in several passes in the sequence shown.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


11. INSTALL CONNECTING ROD BEARING

  1. A111368E02
    Install the bearings in the connecting rod and connecting rod cap.

  1. Using vernier calipers, measure the distance between the bearing cap's and bearing's edge.

    Dimension (A to B):
    0.7 mm (0.028 in.) or less

    NOTICE:
    Clean the backside of the bearing and the bearing surface of the connecting rod.


12. INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD
  1. Apply engine oil to the cylinder walls, the pistons, and the surfaces of the connecting rod bearings.

  1. A111366E04
    Position the piston rings so that the ring ends are as shown in the illustration.

    NOTICE:
    Do not align the ring ends.

  1. A111369E02
    Using a piston ring compressor, push the correctly numbered piston and connecting rod into the cylinder with the front mark of the piston facing forward.

    NOTICE:
    Match the numbered connecting rod cap with the connecting rod.

  1. A111307E03
    Check that the front mark of the connecting rod cap is facing forward.

  1. Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.

  1. A111308E01
    Install and alternately tighten the bolts of the connecting rod cap in several steps.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. A101478E06
    Mark the front side of each connecting cap bolt with paint.

  1. Retighten the cap bolts by 90° as shown.

  1. Check that the painted mark is now at a 90° angle to the front.

  1. Check that the crankshaft turns smoothly.


13. INSTALL ENGINE BALANCER ASSEMBLY

  1. A111301E03
    Align the drive and driven gear's timing marks (1 dot mark each) by turning the crankshaft with a wrench.

  1. A111303E01
    Set the engine balancer.

  1. Install the engine balancer bolts.

    HINT:
    The engine balancer bolts are tightened in 2 progressive steps.

  1. Step 1

    1. Install and uniformly tighten the 8 bolts in several passes in the sequence shown.

      Torque:
      50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. A101478E06
    Step 2

    1. Mark the front of the engine balancer bolts with paint.

    2. Retighten the engine balancer bolts by 90° as shown.

    3. Check that the painted mark is now at a 90° angle to the front.

  1. Install the oil baffle plate with the 2 bolts (*1).

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Remove the service bolt from the engine balancer.


14. INSTALL ENGINE REAR OIL SEAL

  1. A111283E01
    Using SST, tap in a new oil seal until its surface is flush with the oil seal retainer edge.
    SST
    09223-56010  

    NOTICE:
    1. Keep the lip free from foreign matter.
    2. Do not tap the oil seal at an angle.


15. INSTALL VALVE SPRING SEAT
  1. Install the valve spring seat to the cylinder head.


16. INSTALL VALVE STEM OIL SEAL
  1. Apply a light coat of engine oil to a new oil seal.

  1. A111374E02
    Using SST, push in the oil seal.
    SST
    09201-41020  

    NOTICE:
    Failure to use SST will cause the seal to be damaged or improperly seated.


17. INSTALL INTAKE VALVE

  1. A101416E02
    Apply plenty of engine oil to the tip area of the intake valve shown in the illustration.

  1. Install the valve, compression spring and spring retainer to the cylinder head.

    NOTICE:
    Install the same parts in the same combination to the original locations.

  1. A111290E03
    Using SST and wooden blocks, compress the spring and install the 2 retainer locks.
    SST
    09202-70020  

  1. A111375E02
    Using a 5 mm pin punch and plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

    NOTICE:
    Do not damage the valve stem tip.


18. INSTALL EXHAUST VALVE

  1. A101419E02
    Apply plenty of engine oil to the tip area of the intake valve shown in the illustration.

  1. Install the valve, compression spring and spring retainer to the cylinder head.

    NOTICE:
    Install the same parts in the same combination to the original locations.

  1. A111289E01
    Using SST and wooden blocks, compress the spring and install the 2 retainer locks.
    SST
    09202-70020  

  1. A111376E02
    Using a 5 mm pin punch and plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

    NOTICE:
    Do not damage the valve stem tip.


19. INSTALL VALVE LASH ADJUSTER ASSEMBLY
  1. Be sure to inspect the valve lash adjuster before installing it (Click here).

  1. A111279
    Install the lash adjusters.

    NOTICE:
    Install the lash adjuster to the original position.


20. INSTALL CYLINDER HEAD SUB-ASSEMBLY

  1. Check the piston protrusions for each cylinder.

    1. Clean the cylinder block with solvent.

    2. Set the piston of the cylinder to be measured to slightly before TDC.

    3. A129525E01
      Place a dial indicator on the cylinder block, and set the measuring tip as shown in the illustration.

    4. Set the dial indicator at 0 mm (0 in.).

      HINT:
      Make sure that the measuring tip is square to the cylinder block gasket surface and piston head when taking the measurements.

    5. Find where the piston head protrudes most by slowly turning the crankshaft clockwise and counterclockwise.

    6. Measure each cylinder at 2 places as shown in the illustration, making a total of 8 measurements.

    7. For the piston protrusion value of each cylinder, use the average of the 2 measurements of each cylinder.

      HINT:
      If the protrusion is not as specified, remove the piston and connecting rod and reinstall it.

      Standard piston protrusion:
      0.300 to 0.560 mm (0.01181 to 0.02205 in.)

  1. A111379E02
    Select a new cylinder head gasket.

    HINT:
    Cylinder head gaskets are marked A, B, C, D or E accordingly.

    New installed cylinder head gasket thickness:
    Cutout mark
    Specified Condition
    A
    1.00 to 1.10 mm (0.0394 to 0.0433 in.)
    B
    1.05 to 1.15 mm (0.0413 to 0.0453 in.)
    C
    1.10 to 1.20 mm (0.0433 to 0.0472 in.)
    D
    1.15 to 1.25 mm (0.0453 to 0.0492 in.)
    E
    1.20 to 1.30 mm (0.0472 to 0.0512 in.)


    1. Select the largest piston protrusion value from the measurements and then select a new appropriate gasket according to the table below.

      Piston protrusion:
      Gasket size
      Specified Condition
      Use A
      0.300 to 0.355 mm (0.01181 to 0.01398 in.)
      Use B
      0.355 to 0.405 mm (0.01398 to 0.0159 in.)
      Use C
      0.405 to 0.455 mm (0.0159 to 0.01791 in.)
      Use D
      0.455 to 0.505 mm (0.01791 to 0.01988 in.)
      Use E
      0.505 to 0.560 mm (0.01988 to 0.02205 in.)

  1. A111380E01
    Using the crankshaft pulley bolt, set the No. 1 cylinder to 90° BTDC/compression.

  1. Place the cylinder head gasket in position on the cylinder block.

  1. Place the cylinder head on the cylinder block.

    NOTICE:
    Be careful of the installation direction.

  1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.

  1. Install the cylinder head bolts.

    HINT:
    1. For new bolts, perform steps 1 to 3. For used bolts, perform only step 1.
    2. If any bolt is broken or deformed, replace it.

  1. Step 1

    1. A123550E02
      Install and uniformly tighten the 10 cylinder head bolts, in several steps in the sequence shown in the illustration.

      Torque:
      50 N*m{ 510 kgf*cm , 37 ft.*lbf }

      HINT:
      If any one of the cylinder head bolts does not meet the torque specification, replace the cylinder head bolt.

    2. Mark the front of the cylinder head bolt with paint.

    3. Retighten the cylinder head bolts by 90° in the sequence shown in the illustration.

    4. Perform the step above twice.

    5. Check that the painted mark is positioned as shown in the illustration.

  1. Step 2

    1. A194924E01
      Loosen the cylinder head bolts by 90° in the sequence shown in the illustration.

    2. Perform the step above again.

    3. Check that the painted mark is positioned as shown in the illustration.

  1. Step 3

    1. A194925E01
      Retighten the cylinder head bolts by 90° in the sequence shown in the illustration.

    2. Perform the above step twice.

    3. Check that the painted mark is positioned as shown in the illustration.


21. INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

  1. A111278E01
    Set the 16 rocker arms to the lash adjusters.

    NOTICE:
    Before and after setting the camshaft and No. 2 camshaft, firmly set the rocker arm to the lash adjuster.


22. INSTALL CAMSHAFT

  1. A111277
    Install the No. 2 bearing cap.

  1. A111209E04
    Apply clean engine oil to the cam of each camshaft, journals of the cylinder head and valve rocker arm.

  1. A111211E04
    Place the No. 2 camshaft on the camshaft carrier as shown in the illustration so that the No. 1 and No. 3 cylinder cam lobes face upward.

    NOTICE:
    A111377E02
    Before and after setting the camshaft and No. 2 camshaft, check that the rocker arm is firmly set to the lash adjuster.

  1. A111212E01
    Align the camshaft and No. 2 camshaft timing mark (1 dot mark each).

  1. Place the camshaft on the camshaft carrier.

  1. A111213E02
    Set the camshaft bearing caps as shown in the illustration.

    HINT:
    Make sure of the marks and numbers on the camshaft bearing caps and place them in each proper position and direction.

  1. Set the oil delivery pipe, bolts and union bolts.

  1. A111214E01
    Temporarily tighten the 2 union bolts.

  1. Uniformly tighten the bolts in the sequence shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf } for 1 to 16
    25 N*m{ 255 kgf*cm , 18 ft.*lbf } for 17 to 20

  1. Tighten the 2 union bolts.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }


23. INSTALL CAMSHAFT TIMING SPROCKET

  1. A111275E01
    Install the crankshaft timing sprocket, camshaft timing sprocket and chain.

  1. Install the camshaft timing sprocket by fitting the straight pin of the No. 2 camshaft into the hole on the camshaft timing sprocket.

  1. Make sure that the timing mark of the timing sprocket and the paint mark of the timing chain align.

  1. A111273
    While holding the hexagon portion of the No. 2 camshaft, tighten the 4 bolts uniformly to install the camshaft timing sprocket to the No. 2 camshaft.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


24. INSTALL NO. 1 CHAIN VIBRATION DAMPER

  1. A111272
    Install the vibration damper with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


25. INSTALL CHAIN TENSIONER SLIPPER

  1. A111271
    Install the tensioner slipper.


26. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

  1. A101303E04
    Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner (*1).

  1. Move the stopper plate downward to set the lock, and insert SST into the stopper plate hole (*2).

    SST
    09240-00020   (09242-00200)

  1. A111270
    Install the chain tensioner with the 2 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Remove SST.


27. INSTALL TIMING CHAIN CASE OIL SEAL
  1. Place the timing chain cover on wooden blocks.

  1. A111269E02
    Using a screwdriver, pry out the oil seal.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Do not damage the surface of the oil seal press fit hole.

  1. A111284E01
    Using SST and a hammer, tap in a new oil seal to a depth between 0 to 0.6 mm (0 to 0.024 in.) from the timing chain cover edge.
    SST
    09223-50010  

    NOTICE:
    1. Keep the lip free from foreign matter.
    2. Do not tap the oil seal at an angle.

  1. Apply MP grease to the lip of the oil seal.


28. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY (w/ Oil Pump)

  1. A111268
    Install a new gasket and O-ring to the timing chain cover as shown in the illustration.

  1. Apply seal packing in a continuous bead to the timing chain cover as shown in the illustration.

    A129526E01

    Seal packing:
    Toyota genuine seal packing block, three bond 1207B or equivalent

    Standard seal width:
    Position
    Specified Condition
    A - A
    2.0 to 4.0 mm (0.079 to 0.157 in.)
    B - B
    8.0 to 10.0 mm (0.315 to 0.394 in.)
    C - C
    Width: 13 mm (0.512 in.)
    Height: 6 mm (0.236 in.)

    NOTICE:
    1. Be sure to clean and degrease the contact surfaces, especially 4 areas indicated by the arrows in the illustration.
    2. When the contact surfaces are wet, wipe them off with an oil-free cloth before applying seal packing.
    3. When applying seal packing to area C - C, apply it in the direction of the white arrows in the illustration.
    4. Install the crankcase within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    5. Do not start the engine for at least 4 hours after installing.

  1. A057108E01
    Apply adhesive to the 4 bolts.

    Adhesive:
    Toyota genuine adhesive 1324, three bond 1324 or equivalent

    HINT:
    Bolt length: 37.5 mm (1.476 in.)

  1. A127990E01
    Temporarily install the timing chain cover with the 4 bolts.

  1. Temporarily install a new seal washer and bolt A.

    HINT:
    Bolt length: 67.5 mm (2.657 in.)

  1. Temporarily install the 8 bolts.

    HINT:
    Bolt length: 37.5 mm (1.476 in.)

  1. Using several steps, install the 13 bolts.

    Torque:
    31.5 N*m{ 321 kgf*cm , 23 ft.*lbf } for except A bolts
    21 N*m{ 214 kgf*cm , 15 ft.*lbf } for A bolt

  1. A111265
    Using a 10 mm socket hexagon wrench, install the timing chain cover tight plug and a new gasket.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


29. INSTALL WATER PUMP ASSEMBLY

  1. A115205E01
    Install a new gasket onto the timing chain cover as shown in the illustration.

  1. Clean the 7 bolts and 7 bolt holes.

  1. A131146E01
    Temporarily install the water pump.

    Standard bolt length:
    Item
    Specified Condition
    Bolt A and C
    45 mm (1.77 in.)
    Bolt B
    30 mm (1.18 in.)


    1. Apply adhesive to 2 or 3 threads of the bolt labeled A.

      Adhesive:
      Toyota genuine adhesive 1324, three bond 1324 or equivalent.

    2. Temporarily install the water pump with the 7 bolts.

  1. A126835
    Tighten the 2 bolts indicated by the arrows in the illustration. Then tighten the other bolts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }


30. INSTALL CRANKSHAFT PULLEY
  1. Align the keyway of the pulley with the key located on the crankshaft, then slide the pulley into place.

  1. A111238E01
    Using SST, install the pulley bolt.
    SST
    09213-58013  
    09330-00021  

    Torque:
    250 N*m{ 2,550 kgf*cm , 184 ft.*lbf }


31. INSTALL OIL STRAINER SUB-ASSEMBLY

  1. A111262
    Install a new O-ring and the oil strainer with the 3 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


32. INSTALL OIL FILTER BRACKET

  1. A111390
    Install a new gasket and the oil filter bracket with the 4 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


33. INSTALL OIL FILTER ELEMENT
  1. Clean the oil filter cap threads and O-ring groove.

  1. A127986E02
    Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.

  1. Set a new oil filter element in the oil filter cap.


34. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

  1. A123532E02
    Apply seal packing in a continuous bead as shown in the illustration.

    Seal packing:
    Toyota genuine seal packing black, three bond 1207B or equivalent

    Standard seal diameter:
    4.0 to 7.0 mm (0.157 to 0.276 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the oil pan within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.
    3. Do not start the engine for at least 4 hours after installing.

  1. A123530
    Install the oil pan with the 18 bolts and 2 nuts.

    Torque:
    10.5 N*m{ 107 kgf*cm , 8 ft.*lbf }

  1. Install a new gasket and the drain plug.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }


35. INSTALL OIL FILLER CAP SUB-ASSEMBLY
  1. Remove any dirt or foreign matter from the installation surface and inside of the engine.

  1. Apply a small amount of engine oil to the O-ring again and install the oil filter cap.

    NOTICE:
    Be careful that the O-ring does not get caught between the parts.

  1. A128154E01
    Using SST, tighten the oil filter cap.
    SST
    09228-06501  

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    NOTICE:
    1. Make sure that the oil filter is installed securely as shown in the illustration.
    2. Be careful that the O-ring does not get caught between the parts.

  1. A116242E03
    Apply a small amount of engine oil to a new drain plug O-ring, and install it to the oil filter cap.

    NOTICE:
    Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.

  1. Install the oil filter drain plug to the filter cap.

    Torque:
    12.5 N*m{ 127.5 kgf*cm , 9.2 ft.*lbf }

    NOTICE:
    Be careful that the O-ring does not get caught between the parts.

  1. A123520
    Close the oil filter element service cover and install the clip.


36. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
  1. Clean the contact surface of the cylinder head cover, cylinder head and timing chain cover.

  1. A111215E05
    Fit a new cylinder head cover gasket and a new No. 2 gasket into the gasket groove on the cover.

  1. Apply a continuous bead of seal packing (diameter: 8 mm (0.31 in.) to the contact surface between the cylinder head assembly and cylinder head cover assembly as shown in the illustration.

    Seal packing:
    Toyota genuine seal packing block, three bond 1207B or equivalent

    Standard seal diameter:
    8 mm (0.31 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover within 3 minutes after applying seal packing.
    3. Do not apply engine oil for at least 2 hours after installing.

  1. Install the gasket to the cylinder head cover.

  1. A134996E01
    Install the cylinder head cover with the 13 bolts, 4 nozzle holder clamp seats, 2 nuts and 2 washers.
    Uniformly tighten the bolts and nuts in several passes.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf } for bolt A (Nozzle holder clamp seat)11 N*m{ 112 kgf*cm , 8 ft.*lbf } for other bolts
    11 N*m{ 112 kgf*cm , 8 ft.*lbf } for nut


37. INSTALL CRANKSHAFT POSITION SENSOR

  1. A102906
    Apply a light coat of engine oil to the O-ring of the sensor.

  1. A133148
    Install the sensor with the bolt.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }

  1. Connect the sensor wire harness clamp.

  1. Connect the sensor connector to the bracket.

  1. Connect the sensor connector.


38. INSTALL CAMSHAFT POSITION SENSOR

  1. A124879
    Apply a light coat of engine oil to the O-ring of the sensor.

  1. A115775
    Install the sensor with the bolt.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }

  1. Connect the sensor connector.

← REPLACEMENT (from Nov 2005)REASSEMBLY (Jan 2007 – Jul 2007) →