2005-2008 RAV4 · Service Manual ENGINE

ADJUSTMENT

Removal / installation · Vehicles built Jan 2007 – Jul 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


2. REMOVE FRONT WHEEL RH

3. REMOVE NO. 1 ENGINE UNDER COVER

4. REMOVE FRONT FENDER APRON RH

5. REMOVE NO. 1 ENGINE COVER

  1. A112206
    Remove the 2 nuts and cover.


6. REMOVE IGNITION COIL ASSEMBLY
  1. Disconnect the 4 ignition coil connectors.

  1. A124400
    Remove the 4 bolts and 4 ignition coils.


7. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A112209
    Disconnect the 2 ventilation hoses from the cylinder head cover.

  1. A112210E01
    Remove the 2 bolts and disconnect the 2 engine wires.

  1. A112211
    Remove the 8 bolts, 2 nuts and cylinder head cover.


8. SET NO. 1 CYLINDER TO TDC/COMPRESSION

  1. A098345E09
    Turn the crankshaft pulley until its groove and the timing mark "0" of the timing chain cover are aligned.

  1. Check that each timing mark of the camshaft timing gear and sprocket is aligned with each timing mark located on the No. 1 and No. 2 bearing caps as shown in the illustration.
    If not, turn the crankshaft by 1 revolution (360°) to align the timing marks as above.


9. CHECK VALVE CLEARANCE

  1. A098170E04
    Check only the valves indicated.

    1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

      Standard valve clearance (cold):
      Item
      Standard Condition
      Intake
      0.21 to 0.27 mm (0.0083 to 0.0106 in.)
      Exhaust
      0.30 to 0.40 mm (0.0118 to 0.0157 in.)

    2. Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve clearance lifters.

  1. Turn the crankshaft 1 revolution (360°) and set the No. 4 cylinder to the TDC/compression.

  1. A098171E04
    Check only the valves indicated.

    1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

      Standard valve clearance (cold):
      Item
      Standard Condition
      Intake
      0.21 to 0.27 mm (0.0083 to 0.0106 in.)
      Exhaust
      0.30 to 0.40 mm (0.0118 to 0.0157 in.)

    2. Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifters.


10. ADJUST VALVE CLEARANCE
  1. Remove the No. 2 camshaft (Click here).

  1. Remove the camshaft (Click here).

  1. Remove the valve lifters.

  1. A001082E01
    Using a micrometer, measure the thickness of the removed valve lifters.

  1. Calculate the thickness of a new lifter so that the valve clearance comes within the specified values.

    New lifter thickness:
    Item
    Specification
    Intake
    A = B + (C - 0.24 mm (0.0095 in.))
    Exhaust
    A = B + (C - 0.35 mm (0.0138 in.))

    A
    New lifter thickness
    B
    Used lifter thickness
    C
    Measured valve clearance
    EXAMPLE (Intake):
    1. Measured intake valve clearance = 0.16 mm (0.0063 in.)
      (Measured - Specification = Excess clearance)
      1. 0.40 mm (0.0158 in.) - 0.24 mm (0.0095 in.) = 0.16 mm (0.0063 in.)
    2. Measured used lifter measurement = 5.250 mm (0.2067 in.)
    3. New lifter thickness = 5.410 mm (0.2130 in.)
      (Excess clearance + Used lifter thickness = Ideal new lifter)
      1. 0.16 mm (0.0063 in.) + 5.250 mm (0.2067 in.) = 5.410 mm (0.2130 in.)
    4. Closest new lifter = 5.420 mm (0.2134 in.)
      1. Select No. 42 lifter

  1. Select a new lifter with a thickness as close as possible to the calculated values.

    HINT:
    1. Lifters are available in 35 sizes in increments of 0.020 mm (0.0008 in.), from 5.060 to 5.740 mm (0.1992 to 0.2260 in.).)

    2. A126901E01
      The identification number inside the valve lifters shows the value to 2 decimal places. (The illustration shows 5.420 mm (0.2134 in.)

  1. Valve lifter selection chart (intake).

    A126931E02

    New lifter thickness 
    Lifter No.
    Thickness
    mm (in.)
    Lifter No.
    Thickness
    mm (in.)
    Lifter No.
    Thickness
    mm (in.)
    06
    5.060 (0.1992)
    30
    5.300 (0.2087)
    54
    5.540 (0.2181)
    08
    5.080 (0.2000)
    32
    5.320 (0.2094)
    56
    5.560 (0.2189)
    10
    5.100 (0.2008)
    34
    5.340 (0.2102)
    58
    5.580 (0.2197)
    12
    5.120 (0.2016)
    36
    5.360 (0.2110)
    60
    5.600 (0.2205)
    14
    5.140 (0.2024)
    38
    5.380 (0.2118)
    62
    5.620 (0.2213)
    16
    5.160 (0.2031)
    40
    5.400 (0.2126)
    64
    5.640 (0.2220)
    18
    5.180 (0.2039)
    42
    5.420 (0.2134)
    66
    5.660 (0.2228)
    20
    5.200 (0.2047)
    44
    5.440 (0.2142)
    68
    5.680 (0.2236)
    22
    5.220 (0.2055)
    46
    5.460 (0.2150)
    70
    5.700 (0.2244)
    24
    5.240 (0.2063)
    48
    5.480 (0.2157)
    72
    5.720 (0.2252)
    26
    5.260 (0.2071)
    50
    5.500 (0.2165)
    74
    5.740 (0.2260)
    28
    5.280 (0.2079)
    52
    5.520 (0.2173)
    -
    -

    Standard intake valve clearance (cold):
    0.21 to 0.27 mm (0.0083 to 0.0106 in.)

    EXAMPLE:
    The 5.250 mm (0.2067 in.) lifter is installed, and the measured clearance is 0.400 mm (0.0157 in.). Replace the 5.250 mm (0.2067 in.) lifter with a new No. 42 lifter.

  1. Valve lifter selection chart (Exhaust).

    A114356E01

    New lifter thickness 
    Lifter No.
    Thickness
    mm (in.)
    Lifter No.
    Thickness
    mm (in.)
    Lifter No.
    Thickness
    mm (in.)
    06
    5.060 (0.1992)
    30
    5.300 (0.2087)
    54
    5.540 (0.2181)
    08
    5.080 (0.2000)
    32
    5.320 (0.2094)
    56
    5.560 (0.2189)
    10
    5.100 (0.2008)
    34
    5.340 (0.2102)
    58
    5.580 (0.2197)
    12
    5.120 (0.2016)
    36
    5.360 (0.2110)
    60
    5.600 (0.2205)
    14
    5.140 (0.2024)
    38
    5.380 (0.2118)
    62
    5.620 (0.2213)
    16
    5.160 (0.2031)
    40
    5.400 (0.2126)
    64
    5.640 (0.2220)
    18
    5.180 (0.2039)
    42
    5.420 (0.2134)
    66
    5.660 (0.2228)
    20
    5.200 (0.2047)
    44
    5.440 (0.2142)
    68
    5.680 (0.2236)
    22
    5.220 (0.2055)
    46
    5.460 (0.2150)
    70
    5.700 (0.2244)
    24
    5.240 (0.2063)
    48
    5.480 (0.2157)
    72
    5.720 (0.2252)
    26
    5.260 (0.2071)
    50
    5.500 (0.2165)
    74
    5.740 (0.2260)
    28
    5.280 (0.2079)
    52
    5.520 (0.2173)
    -
    -

    Standard exhaust valve clearance (cold):
    0.32 to 0.38 mm (0.0126 to 0.0150 in.)

    EXAMPLE:
    The 5.340 mm (0.2102 in.) lifter is installed, and the measured clearance is 0.430 mm (0.0169 in.). Replace the 5.340 mm (0.2102 in.) lifter with a new No. 42 lifter.

  1. Install the selected valve lifter.


11. INSTALL CAMSHAFT
  1. Apply a light coat of engine oil to the journal portion of the camshaft.

  1. A098176E03
    Install the timing chain onto the camshaft timing gear with the paint mark aligned with the timing mark in the camshaft timing gear as shown in the illustration.

  1. A098177E03
    Examine the front marks and numbers, and check that the order is as shown in the illustration. Then install the bearing caps into the cylinder head.

  1. Apply a light coat of engine oil on the threads and under the heads of the bearing cap bolts.

  1. A098177E05
    Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.

    Torque:
    29.5 N*m{ 301 kgf*cm , 22 ft.*lbf } for No. 1 bearing cap
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for No. 3 bearing cap


12. INSTALL NO. 2 CAMSHAFT
  1. Apply a light coat of engine oil to the journal portion of the No. 2 camshaft.

  1. A098178E02
    Put the No. 2 camshaft on the cylinder head with the paint mark of the chain aligned with the timing mark on the camshaft timing sprocket.

  1. A052473E01
    While holding the No. 2 camshaft by hand, temporarily tighten the camshaft timing sprocket set bolt.

  1. A098174E05
    Examine the front marks and numbers, and check that the order is as shown in the illustration. Then install the bearing caps onto the cylinder head.

  1. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.

  1. A098174E06
    Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.

    Torque:
    29.5 N*m{ 301 kgf*cm , 22 ft.*lbf } for No. 2 bearing cap
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for No. 3 bearing cap

  1. A098173E04
    While holding the camshaft with a wrench, tighten the camshaft timing sprocket set bolt.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

    NOTICE:
    Be careful not to damage the valve lifter.

  1. A098180E03
    Check that the paint marks on the chain are aligned with the timing marks on the camshaft timing gear and camshaft timing sprocket. Also, check that the crankshaft pulley groove is aligned with the timing mark "0" of the timing chain cover.


13. INSTALL NO. 1 CHAIN TENSIONER

  1. A098376E03
    Release the ratchet pawl, then fully push in the plunger and hook the hook to the pin so that the plunger is in the position shown in the illustration.

  1. A098377E02
    Install a new gasket and the chain tensioner with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    When installing the chain tensioner, set the hook again if the hook releases the plunger.

  1. A112204E01
    Turn the crankshaft counterclockwise, then disconnect the plunger knock pin from the hook.

  1. A112205E01
    Turn the crankshaft clockwise, then check that the plunger is extended.


14. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
  1. Remove any old packing material from the contact surface.

  1. A094205E01
    Apply seal packing to the 2 locations shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    1. Install the oil pan within 3 minutes of applying seal packing.
    1. Do not add engine oil for at least 2 hours after installing the oil pan.

  1. A094204E01
    Install the cylinder head cover with the 8 bolts and 2 nuts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf } for bolt A
    14 N*m{ 143 kgf*cm , 10 ft.*lbf } for bolt B
    11 N*m{ 112 kgf*cm , 8 ft.*lbf } for nut

  1. A112210
    Install the 2 engine wires with the 2 bolts.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }

  1. A112209
    Connect the 2 ventilation hoses to the cylinder head cover.


15. INSTALL IGNITION COIL ASSEMBLY

  1. A124400
    Install the 4 ignition coils with the 4 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the 4 ignition coil connectors.


16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

17. CHECK FOR ENGINE OIL LEAKS
  1. Start the engine, and check that there are no oil leaks.


18. INSTALL NO. 1 ENGINE COVER

  1. A112206
    Install the engine cover with the 2 nuts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }


19. INSTALL FRONT FENDER APRON RH

20. INSTALL NO. 1 ENGINE UNDER COVER

21. INSTALL FRONT WHEEL RH
← ADJUSTMENT (Nov 2005 – Dec 2006)ADJUSTMENT (from Aug 2007) →