2005-2008 RAV4 · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. INSTALL NO. 2 CHAIN SUB-ASSEMBLY

  1. B011424E01
    Set the crankshaft key in the left horizontal position.

  1. Turn the cutout of the drive shaft so that it faces upward.

  1. A094198E06
    Align the yellow mark links with the timing marks of each gear as shown in the illustration.

  1. Install the sprockets onto the crankshaft and oil pump shaft with the chain wrapped on the gears.

  1. Temporarily tighten the oil pump drive shaft sprocket with the nut.

  1. A090851E03
    Insert the damper spring into the adjusting hole, and then install the chain tensioner plate with the bolt.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. A098352E01
    Align the adjusting hole of the oil pump drive shaft sprocket with the groove of the oil pump.

  1. Insert a 4 mm diameter bar into the adjusting hole of the oil pump drive shaft gear to lock the gear in position, and then tighten the nut.

    Torque:
    29.5 N*m{ 301 kgf*cm , 22 ft.*lbf }


2. INSTALL CRANKSHAFT TIMING SPROCKET

A128186

3. INSTALL NO. 1 CHAIN VIBRATION DAMPER

  1. A132570
    Install the chain vibration damper with the 2 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


4. INSTALL CHAIN SUB-ASSEMBLY

  1. A098367E01
    Set the No. 1 cylinder to TDC/compression.

    1. Turn the camshafts with a wrench (using the hexagonal lobe) to align the timing marks of the camshaft timing gear with each timing mark located on the No. 1 and No. 2 bearing caps as shown in the illustration.

    2. A052505E01
      Using the crankshaft pulley bolt, turn the crankshaft to position the key on the crankshaft upward.

  1. A094576E01
    Install the chain onto the crankshaft timing sprocket with the gold or orange mark link aligned with the timing mark on the crankshaft.

  1. A098369E01
    Using SST and a hammer, tap in the crankshaft timing sprocket.
    SST
    09309-37010  

  1. A098370E01
    Align the gold or yellow links with each timing mark located on the camshaft timing gear and sprocket, then install the chain.


5. INSTALL CHAIN TENSIONER SLIPPER

  1. A124787E01
    Install the chain tensioner slipper with the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


6. INSTALL TIMING CHAIN GUIDE

  1. A077243E01
    Install the timing chain guide with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


7. INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

  1. A124770
    Install the sensor plate with the "F" mark facing forward.


8. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
  1. Remove any old packing material and be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head and cylinder block.

  1. A094577E01
    Apply seal packing (Diameter 4.0 to 4.5 mm (0.157 to 0.177 in.)) as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    1. Install the chain cover within 3 minutes of applying seal packing.
    1. Do not add engine oil for at least 2 hours after installing the chain cover.

  1. Apply a continuous bead of seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    1. Install the chain cover within 3 minutes of applying seal packing.

    1. Do not add engine oil for at least 2 hours after installing the chain cover.

      A132566E02

  1. A124851E01
    Install the timing chain cover with the 11 bolts and 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for bolt A
    25 N*m{ 255 kgf*cm , 18 ft.*lbf } for bolt B
    55 N*m{ 561 kgf*cm , 41 ft.*lbf } for bolt C
    11 N*m{ 112 kgf*cm , 8 ft.*lbf } for nut

    HINT:
    Bolt length:
    Bolt A
    30 mm (1.18 in.) length for 10 mm head
    Bolt B
    30 mm (1.18 in.) length for 12 mm head
    Bolt C
    40 mm (1.57 in.) length for 14 mm head

  1. A014253E01
    Using an E10 "torx" socket, install the stud bolt for the V-ribbed belt tensioner.

    Torque:
    21.5 N*m{ 219 kgf*cm , 16 ft.*lbf }


9. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

  1. A098376E03
    Release the ratchet pawl, then fully push in the plunger and hook the hook to the pin so that the plunger is in the position shown in the illustration.

  1. A098377E03
    Install a new gasket and the chain tensioner with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    When installing the chain tensioner, set the hook again if the hook releases the plunger.


10. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

  1. A112212
    Install the V-ribbed belt tensioner with the bolt and nut.

    Torque:
    59.5 N*m{ 607 kgf*cm , 44 ft.*lbf }

    NOTICE:
    Do not lift the engine more than necessary.


11. INSTALL ENGINE MOUNTING BRACKET RH

  1. A128165
    Install the engine mounting bracket RH with the 3 bolts.

    Torque:
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }


12. INSTALL CRANKSHAFT PULLEY

  1. A098346E01
    Using SST, fix the pulley in place and tighten the bolt.
    SST
    09213-54015   (91651-60855)
    09330-00021  

    Torque:
    180 N*m{ 1,835 kgf*cm , 133 ft.*lbf }

  1. A112204E01
    Turn the crankshaft counterclockwise, then disconnect the plunger knock pin from the hook.

  1. A112205E01
    Turn the crankshaft clockwise, then check that the plunger is extended.


13. INSTALL OIL PAN SUB-ASSEMBLY
  1. Remove any old packing material and be careful not to drop any oil on the contact surfaces of the cylinder block and oil pan.

  1. A098374E02
    Apply a continuous bead of seal packing (Diameter 3.0 to 4.0 mm (0.118 to 0.157 in.)) as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    1. Install the oil pan within 3 minutes of applying seal packing.
    1. Do not add engine oil for at least 2 hours after installing the oil pan.

  1. Install the oil pan to the cylinder block.

  1. A064641E07
    Uniformly tighten the 12 bolts and 2 nuts in the sequence shown in the illustration.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. A061184E04
    Place a transmission jack underneath the engine, then put a wooden block on the jack.

  1. Remove the chain block and sling device.

  1. Remove the No. 1 and No. 2 engine hangers.


14. INSTALL CRANKSHAFT POSITION SENSOR

A095436E01

NOTICE:
Make sure that the O-ring is not cracked or jammed when installing.

  1. Apply a light coat of engine oil to the O-ring of the sensor.

  1. A116845E01
    Install the sensor with the bolt.

    Torque:
    9.0 N*m{ 90 kgf*cm , 80 in.*lbf }

  1. Install the wire harness clamp.

  1. Install the connector clamp.

  1. Connect the sensor connector.

  1. Confirm that the wire harness of the sensor is secured to the wire harness clamp bracket through the back of the rib of the timing chain cover.


15. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
  1. Remove any old packing material from the contact surface.

  1. A094205E01
    Apply seal packing to the 2 locations shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    1. Install the oil pan within 3 minutes of applying seal packing.
    1. Do not add engine oil for at least 2 hours after installing the oil pan.

  1. A094204E01
    Install the cylinder head cover with the 8 bolts and 2 nuts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf } for bolt A
    14 N*m{ 143 kgf*cm , 10 ft.*lbf } for bolt B
    11 N*m{ 112 kgf*cm , 8 ft.*lbf } for nut

  1. A112210
    Install the 2 engine wires with the 2 bolts.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }

  1. A112209
    Connect the 2 ventilation hoses to the cylinder head cover.


16. INSTALL IGNITION COIL ASSEMBLY

  1. A124400
    Install the 4 ignition coils with the 4 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the 4 ignition coil connectors.


17. INSTALL IDLER PULLEY BRACKET

  1. A132481
    Install the bracket with the 2 bolts.

    Torque:
    60 N*m{ 612 kgf*cm , 44 ft.*lbf }


18. INSTALL ENGINE MOUNTING INSULATOR RH

  1. A124843E01
    Install the engine mounting insulator RH with the 4 bolts and 2 nuts.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf } for bolt
    95 N*m{ 969 kgf*cm , 70 ft.*lbf } for nut A
    52 N*m{ 530 kgf*cm , 38 ft.*lbf } for nut B


19. INSTALL ENGINE MOUNTING INSULATOR FR

  1. A124840
    Install the engine mounting insulator FR with the 2 bolts.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }

  1. A124839
    Install the bolt which is used to secure the front engine mounting bracket FR.

    Torque:
    145 N*m{ 1479 kgf*cm , 107 ft.*lbf }

  1. A098189E01
    Connect the 2 clamps of the engine wire.

  1. Install the wire harness protector with the bolt.


20. INSTALL RADIATOR RESERVOIR TANK

  1. A124838
    Install the radiator reservoir with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


21. INSTALL GENERATOR ASSEMBLY

  1. A097394E02
    Confirm that the wire harness of the crankshaft position sensor is secured to the wire harness clamp bracket through the back of the rib of the timing chain cover.

  1. A122816E01
    Install the generator with the 2 bolts.

    Torque:
    21 N*m{ 215 kgf*cm , 16 ft.*lbf } for bolt A
    52 N*m{ 530 kgf*cm , 38 ft.*lbf } for bolt B

  1. A122809
    Install the wire harness clamp.

  1. Install the wire harness clamp bracket with the bolt.

    Torque:
    8.4 N*m{ 85 kgf*cm , 74 in.*lbf }

  1. Connect the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }

  1. Install the terminal cap.

  1. Connect the generator connector.


22. INSTALL FAN AND GENERATOR V BELT

  1. A114351E01
    Using SST 19 mm socket wrench, loosen the V-ribbed belt tensioner arm clockwise, then install the fan and generator V belt.
    SST
    09216-42010  

    NOTICE:
    1. Be sure to connect SST and the tools so that they are in line during use.
    2. When retracting the tensioner, turn it clockwise slowly for 3 seconds or more. Do not apply force rapidly.
    3. After the tensioner is fully retracted, do not apply force any more than necessary.


23. INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH
  1. Install the reinforcement RH with the 4 bolts.

    Torque:
    96 N*m{ 989 kgf*cm , 71 ft.*lbf }


24. INSTALL FRONT EXHAUST PIPE

  1. A077857E03
    Using a vernier caliper, measure the free length of the compression spring.

    Minimum length:
    41.5 mm (1.634 in.)

    If the length is less than the minimum, replace the compression spring.

  1. A133205E01
    Install a new gasket by hand so that its surface is flush with the exhaust manifold.

    NOTICE:
    1. Make sure the gasket is facing the correct direction.
    2. Do not reuse the removed gasket.
    3. Do not push in the gasket while installing the front exhaust pipe.

  1. Install the front exhaust pipe with the 2 compression springs and 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }


    A126831


25. ADD ENGINE OIL
  1. Clean and install the oil drain plug with a new gasket.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. Add new oil.

    Standard capacity:
    Item
    Specified Condition
    Drain and refill with oil filter change
    4.2 liters (4.4 US qts, 3.7 Imp. qts)
    Drain and refill without oil filter change
    4.0 liters (4.2 US qts, 3.5 Imp. qts)
    Dry fill
    4.9 liters (5.2 US qts, 4.3 Imp. qts)

  1. Install the oil filler cap.


26. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

27. CHECK FOR ENGINE OIL LEAKS
  1. Start the engine, and check that there are no oil leaks.


28. CHECK FOR EXHAUST GAS LEAKS

29. INSTALL NO. 1 ENGINE COVER

  1. A112206
    Install the engine cover with the 2 nuts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }


30. INSTALL FRONT FENDER APRON RH

31. INSTALL NO. 1 ENGINE UNDER COVER

32. INSTALL FRONT WHEEL RH

33. INSTALL RADIATOR SUPPORT OPENING COVER
← REPLACEMENT (from Nov 2005)COMPONENTS (from Nov 2005) →