2005-2008 RAV4 · Service Manual ENGINE

REPLACEMENT

Removal / installation · Vehicles built from Nov 2005


1. REPLACE INTAKE VALVE GUIDE BUSH

  1. A124781
    Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.

  1. A098136E01
    Using SST and a hammer, tap out the guide bush.
    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

  1. A124781
    Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.

  1. A124782
    Using a caliper gauge, measure the bush bore diameter of the cylinder head.

    Standard diameter:
    10.285 to 10.306 mm (0.4049 to 0.4058 in.)

    If the bush bore diameter of the cylinder head is greater than 10.306 mm (0.4058 in.), machine the bush bore to the dimension of 10.335 to 10.365 mm (0.4068 to 0.4077 in.).

    Standard valve guide bush diameter:
    Condition
    Specified Condition
    STD
    10.333 to 10.344 mm (0.4068 to 0.4072 in.)
    O/S
    (0.05 mm)
    10.383 to 10.394 mm (0.4088 to 0.4092 in.)

    If the bushing bore diameter of the cylinder head is greater than 10.394 mm (0.4092 in.), replace the cylinder head.

  1. A098138E01
    Using SST and a hammer, tap in a new guide bush to the specified protrusion height.
    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

    Standard protrusion height:
    9.6 to 10.0 mm (0.378 to 0.394 in.)

  1. A124783
    Using a sharp 5.5 mm reamer, ream the valve guide bush to the standard specified clearance between the valve guide bush and valve stem.

    Standard oil clearance:
    0.025 to 0.060 mm (0.0010 to 0.0024 in.)


2. REPLACE EXHAUST VALVE GUIDE BUSH

  1. A124781
    Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.

  1. A098137E01
    Using SST and a hammer, tap out the guide bush.
    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

  1. A087006E03
    Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.

  1. A124782
    Using a caliper gauge, measure the bush bore diameter of the cylinder head.

    Standard diameter:
    10.285 to 10.306 mm (0.4049 to 0.4058 in.)

    If the bush bore diameter of the cylinder head is greater than 10.306 mm (0.4058 in.), machine the bush bore to the dimension of 10.335 to 10.365 mm (0.4068 to 0.4077 in.).

    Standard valve guide bush diameter:
    Condition
    Specified Condition
    STD
    10.333 to 10.344 mm (0.4068 to 0.4072 in.)
    O/S
    (0.05 mm)
    10.383 to 10.394 mm (0.4088 to 0.4092 in.)

    If the bushing bore diameter of the cylinder head is greater than 10.394 mm (0.4092 in.), replace the cylinder head.

  1. A098139E01
    Using SST and a hammer, tap in a new guide bush to the specified protrusion height.
    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

    Standard protrusion height:
    9.6 to 10.0 mm (0.378 to 0.394 in.)

  1. A124783
    Using a sharp 5.5 mm reamer, ream the valve guide bush to the standard specified clearance between the valve guide bush and valve stem.

    Standard oil clearance:
    0.030 to 0.065 mm (0.0012 to 0.0026 in.)


3. REPLACE STUD BOLT

NOTICE:
If the stud bolt is deformed or threads are damaged, replace it.

  1. Using E5 and E7 "torx" socket wrenches, remove the 11 stud bolts.

  1. Using E5 and E7 "torx" socket wrenches, install the 11 stud bolts.

    A098141E04


4. REPLACE RING PIN

NOTICE:
It is not necessary to remove with head pin unless it is being replaced.

  1. Remove the 4 ring pins.

  1. A098140E04
    Using a plastic-faced hammer, tap in 4 new ring pins to the specified protrusion height.

    Protrusion height:
    3.0 mm (0.12 in.)

← INSPECTION (from Aug 2007)REASSEMBLY (from Nov 2005) →