INSPECTION
Inspection · Vehicles built from Nov 2005
| INSPECT CYLINDER BLOCK FOR WARPAGE |
Using a precision straightedge and feeler gauge, measure the warpage of the surface that is in contact with the cylinder head gasket.

- Maximum warpage:
- 0.05 mm (0.0020 in.)
| INSPECT CYLINDER BORE |
Using a cylinder gauge, measure the cylinder bore diameter at positions A and B in the thrust and axial directions.

- Standard diameter:
- 86.000 to 86.013 mm (3.3858 to 3.3863 in.)
- Maximum diameter:
- 86.133 mm (3.3911 in.)
| INSPECT PISTON |
Using a gasket scraper, remove the carbon from the piston top.

Using a groove cleaning tool or a broken ring, clean the piston ring grooves.

Using a brush and solvent, thoroughly clean the piston.

- NOTICE:
- Do not use a wire brush.
Using a micrometer, measure the piston diameter at right angles to the piston pin hole, and at the piston 30.3 mm (1.193 in.) from the piston head.

- Standard piston diameter:
- 85.927 to 85.937 mm (3.3829 to 3.3833 in.)
| INSPECT PISTON OIL CLEARANCE |
Subtract the piston diameter measurement from the cylinder bore diameter measurement.
- Standard oil clearance:
- 0.063 to 0.086 mm (0.0025 to 0.0034 in.)
- Maximum oil clearance:
- 0.10 mm (0.0039 in.)
| INSPECT RING GROOVE CLEARANCE |
Using a feeler gauge, measure the clearance between the new piston ring and wall of the ring groove.

- Standard ring groove clearance:
Item
Specified Condition
No. 1 ring
0.020 to 0.070 mm (0.0008 to 0.0028 in.)
No. 2 ring
0.020 to 0.060 mm (0.0008 to 0.0024 in.)
Oil ring
0.070 to 0.150 mm (0.0028 to 0.0059 in.)
| INSPECT PISTON RING END GAP |
Using a piston, push the piston ring a little beyond the bottom of the ring travel, 110 mm (4.33 in.) from the top of the cylinder block.

Using a feeler gauge, measure the end gap.

- Standard end gap:
Item
Specified Condition
No. 1 ring
0.30 to 0.40 mm (0.0118 to 0.0157 in.)
No. 2 ring
0.47 to 0.62 mm (0.0185 to 0.0244 in.)
Oil ring
0.10 to 0.35 mm (0.0039 to 0.0138 in.)
- Maximum end gap:
Item
Specified Condition
No. 1 ring
0.89 mm (0.0350 in.)
No. 2 ring
1.37 mm (0.0539 in.)
Oil ring
0.73 mm (0.0287 in.)
| INSPECT PISTON PIN OIL CLEARANCE |
Using a caliper gauge, measure the piston pin bore diameter.

- Standard piston pin bore diameter:
- 22.001 to 22.010 mm (0.8662 to 0.8665 in.)
If the diameter is not as specified, replace the piston.Item
Specified Condition
A
22.001 to 22.004 mm (0.8662 to 0.8663 in.)
B
22.005 to 22.007 mm (0.8663 to 0.8664 in.)
C
22.008 to 22.010 mm (0.8665 to 0.8665 in.)
Using a micrometer, measure the piston pin diameter.

- Standard piston pin diameter:
- 21.997 to 22.006 mm (0.8660 to 0.8664 in.)
If the diameter is not as specified, replace the piston pin.Item
Specified Condition
A
21.997 to 22.000 mm (0.8660 to 0.8661 in.)
B
22.001 to 22.003 mm (0.8662 to 0.8663 in.)
C
22.004 to 22.006 mm (0.8663 to 0.8664 in.)
Using a caliper gauge, measure the connecting rod small end bore diameter.

- Standard connecting rod small end bore diameter:
- 22.005 to 22.014 mm (0.8663 to 0.8667 in.)
If the diameter is not as specified, replace the connecting rod.Item
Specified Condition
A
22.005 to 22.008 mm (0.8663 to 0.8665 in.)
B
22.009 to 22.011 mm (0.8665 to 0.8666 in.)
C
22.012 to 22.014 mm (0.8666 to 0.8667 in.)
Subtract the piston pin diameter measurement from the piston pin bore diameter measurement.

- Standard oil clearance:
- 0.001 to 0.007 mm (0.00004 to 0.0003 in.)
- Maximum oil clearance:
- 0.013 mm (0.0005 in.)
Subtract the piston pin diameter measurement from the connecting rod small end bore diameter measurement.
- Standard oil clearance:
- 0.005 to 0.011 mm (0.0002 to 0.0004 in.)
- Maximum oil clearance:
- 0.017 mm (0.0007 in.)
| INSPECT CONNECTING ROD SUB-ASSEMBLY |
Using a connecting rod aligner and feeler gauge, check the connecting rod alignment.

Check for misalignment.
- Maximum misalignment:
- 0.05 mm (0.0020 in.) per 100 mm (3.94 in.)
Check for twist.

- Maximum twist:
- 0.15 mm (0.0059 in.) per 100 mm (3.94 in.)
| INSPECT CONNECTING ROD BOLT |
Using a vernier caliper, measure the tension portion diameter of the bolt.

- Standard diameter:
- 7.2 to 7.3 mm (0.283 to 0.287 in.)
- Minimum diameter:
- 7.0 mm (0.276 in.)
| INSPECT CRANKSHAFT |
Using a dial indicator and V-blocks, measure the circle runout as shown in the illustration.

- Maximum taper and distortion:
- 0.003 mm (0.0001 in.)
Using a micrometer, measure the diameter of each main journal.

- Standard diameter:
- 54.988 to 55.000 mm (2.1649 to 2.1654 in.)
Check each main journal for taper and distortion as shown in the illustration.
- Maximum taper and distortion:
- 0.003 mm (0.0001 in.)
- Standard diameter (Reference):
Mark
Specified Condition
0
54.999 to 55.000 mm (2.1653 to 2.1654 in.)
1
54.997 to 54.998 mm (2.1652 to 2.1653 in.)
2
54.995 to 54.996 mm (2.1652 to 2.1652 in.)
3
54.993 to 54.994 mm (2.1651 to 2.1651 in.)
4
54.991 to 54.992 mm (2.1650 to 2.1650 in.)
5
54.988 to 54.990 mm (2.1649 to 2.1650 in.)
Using a micrometer, measure the diameter of each crank pin.

- Standard diameter:
- 47.990 to 48.000 mm (1.8894 to 1.8898 in.)
Inspect each crank pin for taper and distortion as shown in the illustration.
- Maximum taper and distortion:
- 0.003 mm (0.0001 in.)
| INSPECT CRANKSHAFT BEARING CAP SET BOLT |
Using a vernier caliper, measure the tension portion diameter of the bolts.

- Standard diameter:
- 7.5 to 7.6 mm (0.295 to 0.299 in.)
- Minimum diameter:
- 7.5 mm (0.295 in.)
