2005-2008 RAV4 · Service Manual ENGINE

DISASSEMBLY

Removal / installation · Vehicles built Jan 2007 – Jul 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. REMOVE IDLER PULLEY BRACKET

  1. A132481
    Loosen the 2 bolts and remove the bracket together with the 2 bolts.


2. REMOVE OIL DIPSTICK

3. REMOVE OIL DIPSTICK GUIDE

  1. A112218
    Remove the bolt and guide.

  1. Remove the O-ring from the guide.


4. REMOVE MANIFOLD STAY

  1. A112193
    Remove the bolt, nut and stay.


5. REMOVE NO. 2 MANIFOLD STAY

  1. A112192
    Remove the bolt, nut and stay.


6. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

  1. A098744E01
    Disconnect the air-fuel ratio sensor connector.

  1. A112189
    Remove the 4 bolts and heat insulator.


7. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

  1. A112190
    Remove the 5 nuts, manifold converter and gasket.


8. REMOVE WATER INLET

A112181
  1. Remove the 2 nuts and disconnect the water inlet from the cylinder block.


9. REMOVE THERMOSTAT

10. REMOVE NO. 1 WATER BY-PASS PIPE (w/o Oil Cooler)

  1. A112226
    Remove the bolt, 2 nuts, pipe and gasket.


11. REMOVE OIL COOLER PIPE (w/ ATF Warmer)

  1. A126940
    Remove the bolt, 2 nuts, pipe and gasket.


12. REMOVE UNION BOLT (w/ Oil Cooler)

  1. A129331
    Remove the union bolt.


13. REMOVE NO. 1 TAPER SCREW PLUG (w/o Oil Cooler)

  1. A036850E01
    Remove the plug from the cylinder block.


14. REMOVE NO. 3 WATER BY-PASS PIPE (w/ Oil Cooler)

  1. A126938E03
    Disconnect the No. 3 and No. 4 water by-pass hoses.

  1. A126879
    Remove the bolt, 2 nuts, pipe and gasket.


15. REMOVE OIL FILTER SUB-ASSEMBLY

  1. A124762E01
    Using SST, remove the oil filter.
    SST
    09228-06501  


16. REMOVE ENGINE OIL COOLER (w/ Oil Cooler)
  1. Disconnect the 2 oil cooler hoses from the oil cooler.

  1. A124387
    Remove the union bolt, nut, plate washer, oil cooler and O-ring.


17. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
  1. Lift the engine upward using the transmission jack.

    NOTICE:
    Do not lift the engine more than necessary.

  1. A112212
    Remove the bolt, nut and V-ribbed belt tensioner.


18. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

  1. A124556
    Disconnect the oil control valve connector.

  1. Remove the bolt and oil control valve.


19. REMOVE KNOCK SENSOR

  1. A095426E01
    Disconnect the sensor connector.

  1. Remove the nut and sensor.


20. REMOVE RADIO SETTING CONDENSER

  1. A112227
    Remove the bolt and condenser.


21. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

  1. A114362
    Using a 24 mm deep socket wrench, remove the sensor.


22. REMOVE ENGINE COOLANT TEMPERATURE SENSOR

  1. A095412E01
    Disconnect the sensor connector.

  1. Using SST, remove the sensor and gasket.

    SST
    09817-33190  


23. REMOVE CAMSHAFT POSITION SENSOR

A124557
  1. Disconnect the sensor connector.

  1. Remove the bolt and sensor.


24. REMOVE IGNITION COIL ASSEMBLY
  1. Disconnect the 4 ignition coil connectors.

  1. A124400
    Remove the 4 bolts and 4 ignition coils.


25. REMOVE SPARK PLUG

A132575

26. REMOVE OIL FILLER CAP SUB-ASSEMBLY

A128158

27. REMOVE OIL FILLER CAP GASKET

A128159

28. REMOVE VENTILATION VALVE SUB-ASSEMBLY

  1. A097786E01
    Disconnect the ventilation hose from the ventilation valve.

  1. A098067E01
    Using a 22 mm deep socket wrench, remove the ventilation valve.


29. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A112209
    Disconnect the 2 ventilation hoses from the cylinder head cover.

  1. A112210E01
    Remove the 2 bolts and disconnect the 2 engine wires.

  1. A112211
    Remove the 8 bolts, 2 nuts and cylinder head cover.


30. REMOVE CYLINDER HEAD COVER GASKET

A128166

31. REMOVE OIL FILTER SUB-ASSEMBLY

  1. A124762E01
    Using SST, remove the oil filter.
    SST
    09228-06501  


32. REMOVE OIL FILTER UNION

  1. A126912E01
    Using a 12 mm hexagon wrench, remove the oil filter union.


33. REMOVE CRANKSHAFT POSITION SENSOR

A097797E02
  1. Disconnect the sensor connector.

  1. Remove the connector clamp.

  1. Remove the wire harness from the wire harness clamp bracket.

  1. Remove the wire harness clamp.

  1. Remove the bolt and sensor.


34. REMOVE WATER PUMP PULLEY

A098715E03
  1. Using SST, remove the 4 bolts and water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)


35. REMOVE WATER PUMP ASSEMBLY

A094516E01
  1. Remove the clamp of the crankshaft position sensor from the water pump.

  1. Disconnect the wire of the crankshaft position sensor from the clamp bracket.

  1. B012052E03
    Remove the 4 bolts, 2 nuts and clamp bracket.

  1. B012053E04
    Using a screwdriver, pry between the water pump and cylinder block, and then remove the water pump.

    NOTICE:
    Be careful not to damage the contact surfaces of the water pump and cylinder block.


36. REMOVE OIL PAN DRAIN PLUG
  1. Remove the oil pan drain plug and gasket.


37. REMOVE OIL PAN SUB-ASSEMBLY

  1. A112213E01
    Install the No. 1 and No. 2 engine hangers with the bolts.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }

    Part No. 
    Item
    Part No.
    No. 1 engine hanger
    12281-28010
    No. 2 engine hanger
    12282-28010
    Bolt
    91512-61020

  1. Attach the sling device to the engine hangers and chain block.

  1. A064641E01
    Remove the 12 bolts and 2 nuts.

  1. A000019E05
    Insert the blade of SST between the crankcase, chain cover and oil pan, then cut off the applied sealer and remove the oil pan.
    SST
    09032-00100  

    NOTICE:
    Be careful not to damage the contact surface of the crankcase, chain cover and oil pan.


38. REMOVE CRANKSHAFT PULLEY

  1. A013697E01
    Using SST, fix the pulley in place and loosen the pulley bolt.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A124860E01
    Remove the crankshaft pulley.

    HINT:
    If necessary, remove the pulley and pulley bolt using SST.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)
    09950-40011   (09957-04010)


39. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

  1. A098348E01
    Remove the 2 nuts, chain tensioner and gasket.

    NOTICE:
    Do not turn the crankshaft without the chain tensioner.


40. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

  1. A014253E01
    Using an E10 "torx" socket, remove the stud bolt for the V-ribbed belt tensioner.

  1. A124851E02
    Remove the 11 bolts and 2 nuts.

  1. A128179
    Remove the timing chain cover by prying the portions between the timing chain cover, cylinder head and cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing chain cover, cylinder head and cylinder block.


41. REMOVE TIMING CHAIN COVER OIL SEAL

  1. A032626E01
    Using a screwdriver and hammer, tap out the oil seal.

  1. Place the oil seal retainer on wooden blocks.

  1. Apply multi-purpose grease to the lip of a new oil seal.

    NOTICE:
    Keep the lip free of foreign objects.

  1. A094547E01
    Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing gear case edge.
    SST
    09223-22010  

    NOTICE:
    Do not tap the oil seal at an angle.


42. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

A132571

43. REMOVE TIMING CHAIN GUIDE

  1. A077243E01
    Remove the bolt and timing chain guide.


44. REMOVE CHAIN TENSIONER SLIPPER

  1. A128183
    Remove the bolt and chain tensioner slipper.


45. REMOVE CHAIN SUB-ASSEMBLY

A128185

46. REMOVE NO. 1 CHAIN VIBRATION DAMPER

  1. A128184
    Remove the 2 bolts and chain vibration damper.


47. REMOVE CRANKSHAFT TIMING SPROCKET

A128186

48. REMOVE NO. 2 CHAIN SUB-ASSEMBLY

  1. A098351E01
    Turn the crankshaft by 90° counterclockwise to align the adjusting hole of the oil pump drive shaft sprocket with the groove of the oil pump.

  1. A098352E01
    Insert a 4 mm diameter bar into the adjusting hole of the oil pump drive shaft sprocket to lock the gear in position, and then remove the nut.

  1. B011415E03
    Remove the bolt, chain tensioner plate and spring.

  1. Remove the oil pump drive sprocket, oil pump drive shaft sprocket and No. 2 chain.


49. REMOVE OIL PUMP DRIVE GEAR

50. REMOVE OIL PUMP ASSEMBLY

  1. B011673E01
    Remove the 3 bolts, oil pump and gasket.


51. REMOVE CAMSHAFT

  1. F050596E02
    Using several steps, uniformly loosen and remove the 20 bearing cap bolts in the sequence shown in the illustration.

  1. Remove the 10 bearing caps, then remove the camshaft and No. 2 camshaft.


52. REMOVE CYLINDER HEAD SUB-ASSEMBLY

  1. F050595E01
    Using several steps, uniformly loosen and remove the 10 cylinder head bolts and 10 plate washers with a 10 mm bi-hexagon wrench in the sequence shown in the illustration.

    NOTICE:
    Head warpage or cracking could result from removing the bolts in the wrong order.

  1. A126930
    Using a screwdriver with its tip wrapped with tape, pry between the cylinder head and cylinder block, and remove the cylinder head.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and cylinder block.


53. REMOVE CYLINDER HEAD GASKET

A126928

54. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

A128209

55. REMOVE OIL CONTROL VALVE FILTER

  1. A098169E01
    Using a 6 mm socket hexagon wrench, remove the plug and gasket.

  1. Remove the oil control valve filter.


56. REMOVE ENGINE REAR OIL SEAL

  1. A098356E01
    Using a knife, cut off the lip of the oil seal.

  1. Using a screwdriver with its tip wrapped with tape, pry out the oil seal.

    NOTICE:
    After removing, check the crankshaft for damage. If damaged, smooth the surface with 400-grit sandpaper.


57. REMOVE STIFFENING CRANKCASE ASSEMBLY

  1. A013843E03
    Using several steps, uniformly loosen and remove the 11 bolts in the sequence shown in the illustration.

  1. A132484
    Remove the crankcase by prying the portions between the crankcase and cylinder block.

    NOTICE:
    Be careful not to damage the contact surfaces of the crankcase and cylinder block.

  1. Remove the O-ring from the cylinder block.


58. INSPECT CONNECTING ROD THRUST CLEARANCE

  1. A112172
    Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

    Standard thrust clearance:
    0.160 to 0.362 mm (0.0063 to 0.0143 in.)

    Maximum thrust clearance:
    0.362 mm (0.0143 in.)

    If the thrust clearance is greater than the maximum, replace the connecting rod. If necessary, replace the crankshaft.


59. INSPECT CONNECTING ROD OIL CLEARANCE

NOTICE:
Do not turn the crankshaft during the measurement.

  1. A132485E01
    Using marking paint, write the matched cylinder number on each connecting rod and cap.

    HINT:
    The matchmarks in the connecting rods and caps are for ensuring correct reassembly.

  1. A013397E03
    Using a 12 mm socket wrench, remove the 2 bolts and connecting rod cap.

  1. Clean the crank pin and bearing.

  1. Check the crank pin and bearing for pitting and scratches.

  1. A132486E01
    Lay a strip of Plastigage on the crank pin.

  1. A132487E01
    Check that the front mark of the connecting rod cap is facing in the correct direction.

  1. Apply a light coat of engine oil to the threads and under the heads of the connecting rod bolts.

  1. Using a 12 mm socket wrench, tighten the bolts in several passes to the specified torque.

    Torque:
    24.5 N*m{ 250 kgf*cm , 18 ft.*lbf }

  1. A098354E01
    Mark the front of the connecting rod bolts with paint.

  1. Retighten the cap bolts 90° as shown in the illustration.

  1. Check that the crankshaft turns smoothly.

  1. Using a 12 mm socket wrench, remove the 2 bolts and connecting rod cap.

  1. A129453E02
    Measure the Plastigage at its widest point.

    Standard oil clearance:
    0.024 to 0.048 mm (0.0009 to 0.0019 in.)

    Maximum oil clearance:
    0.08 mm (0.0032 in.)

    NOTICE:
    Remove the Plastigage completely after the measurement.

    If the oil clearance is greater than the maximum, replace the connecting rod bearing. If necessary, grind or replace the crankshaft.

    HINT:
    If replacing a bearing, select a new one with the same number as marked on the connecting rod. There are 3 sizes of standard bearings, marked "1", "2" and "3" accordingly.

    Standard connecting rod large end bore diameter:
    Mark
    Specified Condition
    Mark 1
    51.000 to 51.007 mm (2.0079 to 2.0082 in.)
    Mark 2
    51.008 to 51.013 mm (2.0082 to 2.0084 in.)
    Mark 3
    51.014 to 51.020 mm (2.0084 to 2.0087 in.)

    Standard connecting rod bearing thickness:
    Mark
    Specified Condition
    Mark 1
    1.485 to 1.488 mm (0.0585 to 0.0586 in.)
    Mark 2
    1.489 to 1.491 mm (0.0586 to 0.0587 in.)
    Mark 3
    1.492 to 1.494 mm (0.0587 to 0.0588 in.)

    Standard crankshaft pin diameter:
    Mark
    Specified Condition
    -
    47.990 to 48.000 (1.8894 to 1.8898 in.)


60. REMOVE PISTON WITH CONNECTING ROD

  1. A013469E01
    Using a ridge reamer, remove all the carbon from the top of the cylinder.

  1. Push the piston, connecting rod assembly and upper bearing through the top of the cylinder block.

    HINT:
    1. Keep the bearing, connecting rod and cap together.
    1. Arrange the piston and connecting rod assemblies in the correct order.


61. REMOVE CONNECTING ROD BEARING

62. REMOVE PISTON RING SET

  1. A036647E01
    Using a piston ring expander, remove the 2 compression rings.

  1. Remove the 2 side rails and expander by hand.


63. REMOVE PISTON PIN HOLE SNAP RING

  1. A013478E01
    Using a small screwdriver, pry out the 2 snap rings.


64. REMOVE PISTON

  1. A001178E02
    Gradually heat the piston up to 80 to 90°C (176 to 194°F).

  1. A001179E01
    Using a plastic-faced hammer and brass bar, lightly tap out the piston pin, then remove the connecting rod.

    HINT:
    1. The piston and pin are a matched set.
    1. Arrange the piston, pin, ring, connecting rod and bearings in the correct order.


65. INSPECT CRANKSHAFT THRUST CLEARANCE

  1. A013851E01
    Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

    Standard thrust clearance:
    0.04 to 0.24 mm (0.0016 to 0.0095 in.)

    Maximum thrust clearance:
    0.30 mm (0.0118 in.)

    If the thrust clearance is greater than the maximum, replace the thrust washers as a set.

    HINT:
    The thrust washer thickness is 1.93 to 1.98 mm (0.0760 to 0.0780 in.).


66. INSPECT CRANKSHAFT OIL CLEARANCE

NOTICE:
Do not turn the crankshaft during the measurement.

  1. Clean each main journal and bearing.

  1. Check each main journal and bearing for pitting and scratches.

  1. A053029E01
    Install the upper bearing with an oil groove onto the cylinder block.

    NOTICE:
    Do not apply engine oil to the contact surfaces of the cylinder block and crankshaft bearing.

  1. A033379E01
    Install the lower bearing onto the bearing cap.

    NOTICE:
    Do not apply engine oil to the contact surfaces of the cylinder block and crankshaft bearing cap.

  1. Place the crankshaft onto the cylinder block.

  1. A132488E01
    Lay a strip of Plastigage across each journal.

  1. A098155E01
    Examine the front marks and numbers, and install the bearing caps onto the cylinder block in the order shown in the illustration.

  1. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.

  1. A132451E01
    Using several steps, uniformly install and tighten the 10 bearing cap bolts in the sequence shown in the illustration.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. A098354E01
    Mark the front of the bearing cap bolts with paint.

  1. Retighten the 10 bearing cap bolts by 90°.

  1. Check that the paint marks are at a 90° angle to the front.

  1. Remove the bearing caps.

  1. Measure the Plastigage at its widest point.

    Standard oil clearance:
    0.017 to 0.040 mm (0.0007 to 0.0016 in.)

    Maximum oil clearance:
    0.050 mm (0.0020 in.)

    NOTICE:
    Remove the Plastigage completely after the measurement.

    If the oil clearance is greater than the maximum, replace the crankshaft bearing. If necessary, replace the crankshaft.

    HINT:
    If replacing a bearing, select a new one with the same number. If the number of the bearing cannot be determined, calculate the correct bearing number by adding together the numbers imprinted on the cylinder block and crankshaft. Then select a new bearing with the calculated number. There are 4 sizes of standard bearings, marked "1", "2", "3" and "4" accordingly.
    Cylinder block + Crankshaft
    0 to 2
    3 to 5
    6 to 8
    9 to 11
    Use bearing
    "1"
    "2"
    "3"
    "4"
    EXAMPLE
    1. Imprinted number on the cylinder block is 3.
    1. Imprinted number on the crankshaft is 4.
      3 + 4 = 7
      Select the bearing marked "3".

      Standard cylinder block journal bore diameter:
      Mark
      Specified Condition
      0
      59.000 to 59.002 mm (2.3228 to 2.3229 in.)
      1
      59.003 to 59.004 mm (2.3230 to 2.3230 in.)
      2
      59.005 to 59.006 mm (2.3230 to 2.3231 in.)
      3
      59.007 to 59.009 mm (2.3231 to 2.3232 in.)
      4
      59.010 to 59.011 mm (2.3232 to 2.3233 in.)
      5
      59.012 to 59.013 mm (2.3233 to 2.3234 in.)
      6
      59.014 to 59.016 mm (2.3234 to 2.3235 in.)

    Standard crankshaft journal diameter:
    Mark
    Specified Condition
    0
    54.999 to 55.000 mm (2.1653 to 2.1654 in.)
    1
    54.997 to 54.998 mm (2.1652 to 2.1653 in.)
    2
    54.995 to 54.996 mm (2.1652 to 2.1652 in.)
    3
    54.993 to 54.994 mm (2.1651 to 2.1651 in.)
    4
    54.991 to 54.992 mm (2.1650 to 2.1650 in.)
    5
    54.988 to 54.990 mm (2.1649 to 2.1650 in.)

    Standard bearing center wall thickness:
    Mark
    Specified Condition
    1
    1.993 to 1.996 mm (0.0785 to 0.0786 in.)
    2
    1.997 to 1.999 mm (0.0786 to 0.0787 in.)
    3
    2.000 to 2.002 mm (0.0787 to 0.0788 in.)
    4
    2.003 to 2.005 mm (0.0789 to 0.0789 in.)


67. REMOVE CRANKSHAFT

  1. A132451E01
    Using several steps, uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.

  1. Remove the 5 bearing caps from the cylinder block.

  1. Remove the crankshaft from the cylinder block.


68. REMOVE CRANKSHAFT THRUST WASHER UPPER

69. REMOVE CRANKSHAFT BEARING

HINT:
Arrange the bearings in the correct order.


70. REMOVE NO. 2 CRANKSHAFT BEARING

HINT:
Arrange the bearings in the correct order.

← DISASSEMBLY (Nov 2005 – Dec 2006)DISASSEMBLY (from Aug 2007) →