B1660/43 Passenger Airbag ON/OFF Indicator Circuit Malfunction
Diagnostic trouble codes · Vehicles built from Jan 2007
Versions by build date: Nov 2005 – Dec 2006 from Jan 2007
DESCRIPTION
The passenger airbag ON / OFF indicator circuit consists of the center airbag sensor and the heater control panel*1 or clock*2.This circuit indicates the operation condition of the front passenger airbag, the front passenger side airbag and passenger side seat belt pretensioner.
DTC B1660/43 is set when a malfunction is detected in the passenger airbag ON / OFF indicator circuit.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1660/43 |
When one of following conditions is met:
|
|
- HINT:
- *1: for Automatic Air Conditioning System
- *2: for Manual Air Conditioning System
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK PASSENGER AIRBAG ON / OFF INDICATOR OPERATION |
Turn the ignition switch on (IG).
Check the passenger airbag ON / OFF indicator operation.


Result ON / OFF Indicator Illumination
Proceed to
Always ON
A
OFF
B
|
|
||||
| A | |
| 2. CHECK CONNECTION OF CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and the front passenger seat belt warning light.
- OK:
- The connectors are properly connected.
|
|
||||
| OK | |
| 3. CHECK FRONT PASSENGER AIRBAG ON/OFF INDICATOR LIGHT |
![]() ![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connector from the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Check the passenger airbag ON / OFF indicator operation.
- OK:
- Neither ON nor OFF passenger airbag ON / OFF indicator comes on.
|
|
||||
| NG | |
| 4. CHECK INSTRUMENT PANEL WIRE (FOR OPEN) |
![]() ![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connector from the front passenger airbag ON / OFF indicator light.
Using a service wire, connect E49-23 (PAON) and E49-17 (P-AB) of connector B.
- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting.
Measure the resistance of the wire harness side connector.
- Standard resistance:
- for Automatic Air Conditioning System:
Tester Connection
Specified Condition
E26-6 (PAON) - E23-13 (P-AB)
Below 1 Ω
- for Manual Air Conditioning System:
Tester Connection
Specified Condition
E25-4 (PAON) - E25-9 (P-AB)
Below 1 Ω
|
|
||||
| OK | |
| 5. CHECK INSTRUMENT PANEL WIRE (FOR SHORT) |
![]() ![]() |
Disconnect the service wire from connector B.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
E49-17 (P-AB) - E49-23 (PAON)
1 MΩ or higher
|
|
||||
| OK | |
| 6. CHECK INSTRUMENT PANEL WIRE (TO B+) |
![]() ![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Connection
Specified Condition
E49-23 (PAON) - Body ground
Below 1 V
E49-17 (P-AB) - Body ground
Below 1 V
|
|
||||
| OK | |
| 7. CHECK INSTRUMENT PANEL WIRE (TO GROUND) |
![]() ![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
E49-17 (P-AB) - Body ground
1 MΩ or higher
E49-23 (PAON) - Body ground
1 MΩ or higher
|
|
||||
| OK | ||
| ||
| 8. CHECK CONNECTION OF CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and the heater control panel*1 or clock*2.
- OK:
- The connectors are properly connected.
|
|
||||
| OK | |
| 9. CHECK INSTRUMENT PANEL WIRE (FOR OPEN) |
![]() ![]() |
Disconnect the connector from the front passenger seat belt warning light.
Using a service wire, connect E49-23 (PAON) and E49-17 (P-AB) of connector B.
- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting.
Measure the resistance of the wire harness side connector.
- Standard resistance:
- for Automatic Air Conditioning System:
Tester Connection
Specified Condition
E26-6 (PAON) - E25-13(P-AB)
Below 1 Ω
- for Manual Air Conditioning System:
Tester Connection
Specified Condition
E25-4 (PAON) - E25-9(P-AB)
Below 1 Ω
|
|
||||
| OK | |
| 10. CHECK INSTRUMENT PANEL WIRE (FOR SHORT) |
![]() ![]() |
Disconnect the service wire from connector B.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
E49-17 (P-AB) - E49-23 (PAON)
1 MΩ or higher
|
|
||||
| OK | |
| 11. CHECK INSTRUMENT PANEL WIRE (TO B+) |
![]() ![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Connection
Specified Condition
E49-23 (PAON) - Body ground
Below 1 V
E49-17 (P-AB) - Body ground
Below 1 V
|
|
||||
| OK | |
| 12. CHECK INSTRUMENT PANEL WIRE (TO GROUND) |
![]() ![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
E49-17 (P-AB) - Body ground
1 MΩ or higher
E49-23 (PAON) - Body ground
1 MΩ or higher
|
|
||||
| OK | |
| 13. CHECK INSTRUMENT PANEL WIRE (POWER SOURCE) |
![]() ![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Connection
Specified Condition
E26-2 (IG+) - Body ground
10 to 14 V
E25-2 (IG+) - Body ground
10 to 14 V
|
|
||||
| OK | |
| 14. CHECK FRONT PASSENGER AIRBAG ON/OFF INDICATOR LIGHT |
![]() ![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connector from the front passenger seat belt warning light.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Using a service wire, connect E26-6*1 E25-4*2 (PAON) and E26-7*1 E25-5*2 (GND) of the heater control panel*1 or clock*2.
- HINT:
- *1: for Automatic Air Conditioning System
- *2: for Manual Air Conditioning System
Using a service wire, connect E26-13*1 E25-9*2 (P-AB) and E26-7*1 E25-5*2 (GND) of the heater control panel*1 or clock*2.
- HINT:
- *1: for Automatic Air Conditioning System
- *2: for Manual Air Conditioning System
Turn the ignition switch on (IG).
Check the passenger airbag ON / OFF indicator operation.
- OK:
- Front passenger airbag ON / OFF indicator comes on
|
|
||||
| OK | |
| 15. CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() ![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Connect the connector to the center airbag sensor.
Connect the connector to the heater control panel*1 or clock*2.
- HINT:
- *1: for Automatic Air Conditioning System
- *2: for Manual Air Conditioning System
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1660/43 is not output.
- HINT:
- DTCs other than DTC B1660/43 may be output at this time, but they are not related to this check.
|
|
||||
| OK | ||
| ||








