2005-2008 RAV4 · Service Manual ENGINE

P1601 EEPROM Error - Injector Correction Value, DPF Thermal Degradation Record

Diagnostic trouble codes · Vehicles built Nov 2005 – Dec 2006

Versions by build date: Nov 2005 – Dec 2006 from Jan 2007

DESCRIPTION

HINT:
Whether the abnormality occurs in the DPNR catalyst thermal deterioration history data or in the injector compensation code can be determined by checking the Data List.

DTC No.
DTC Detection Condition
Trouble Area
P1601
When either condition below is met:
  1. Injector compensation code is not registered (1 trip detection logic)
  2. Wrong injector compensation code is registered (1 trip detection logic)
  1. Injector compensation code
  2. ECM
When either condition below is met:
  1. The DPNR catalyst thermal deterioration history data in the ECM is still the initial value (1 trip detection logic)
  2. The DPNR catalyst thermal deterioration history data is not recorded correctly in the ECM (2 trip detection logic)

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).


1. CONFIRM ECM
  1. Confirm if DTC P1601 was output because a new ECM was installed.

    Result:
    Result
    Proceed to
    DTC P1601 was output due to new ECM being installed
    A
    DTC P1601 was output due to original ECM malfunction
    B



A
Go to step 15
B


2. CHECK DTC OUTPUT
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P1601
    A
    Other output
    B



B
GO TO DTC CHART
A


3. CHECK DATA LIST (INJECTOR MEMORY ERROR AND DPNR CATALYST DETERIORATE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Catalyst Memory Error and Injector Memory Error.

    Result:
    Item
    Proceed to
    Catalyst Memory Error: Error
    Injector Memory Error: No Error
    A
    Catalyst Memory Error: No Error
    Injector Memory Error: Error
    B
    Catalyst Memory Error: Error
    Injector Memory Error: Error
    C



B
Go to step 8

C
Go to step 12
A


4. READ INJECTOR COMPENSATION CODE
  1. Using the intelligent tester, read the injector compensation code (Click here).


NEXT


5. REPLACE ECM AND EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
  1. Replace the ECM (Click here).

  1. Replace the exhaust manifold converter sub-assembly.


NEXT


6. REGISTER INJECTOR COMPENSATION CODE
  1. Input the injector compensation code read with the intelligent tester (Click here).


NEXT


7. CLEAR CATALYST RECORD
  1. Clear the catalyst record of DPNR thermal deterioration (Click here).


NEXT

END

8. READ CATALYST RECORD OF DPNR THERMAL DETERIORATION
  1. Read the catalyst record of DPNR thermal deterioration (Click here).


NEXT


9. REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


10. SET CATALYST RECORD OF DPNR THERMAL DETERIORATION
  1. Set the catalyst record of DPNR thermal deterioration (Click here).


NEXT


11. REGISTER INJECTOR COMPENSATION CODE
  1. Input the injector compensation code written on the injector (Click here).


NEXT

END

12. REPLACE ECM AND EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
  1. Replace the ECM (Click here).

  1. Replace the exhaust manifold converter sub-assembly.


NEXT


13. REGISTER INJECTOR COMPENSATION CODE
  1. Input the injector compensation code written on the injector (Click here).


NEXT


14. CLEAR CATALYST RECORD
  1. Clear the catalyst record of DPNR thermal deterioration (Click here).


NEXT

END

15. CHECK DTC OUTPUT
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P1601
    A
    Other output
    B



B
GO TO DTC CHART
A


16. CHECK DATA LIST (INJECTOR MEMORY ERROR AND DPNR CATALYST DETERIORATE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Catalyst Memory Error and Injector Memory Error.

    Result:
    Item
    Proceed to
    Catalyst Memory Error: Error
    Injector Memory Error: No Error
    A
    Catalyst Memory Error: No Error
    Injector Memory Error: Error
    B
    Catalyst Memory Error: Error
    Injector Memory Error: Error
    C



B
Go to step 22

C
PERFORM PROCEDURE A AND B
A


17. CHECK EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
  1. Confirm if the exhaust manifold converter sub-assembly has been replaced or not during the current repair.



YES
Go to step 21
NO


18. CHECK IF DTC P1601 IS OUTPUT IN ORIGINAL ECM
  1. Check if DTC P1601 was output in the original ECM.



YES
Go to step 21
NO


19. CHECK CATALYST RECORD OF DPNR THERMAL DETERIORATION
  1. Read the catalyst record of DPNR thermal deterioration from old ECM (Click here).

  1. Set the catalyst record of DPNR thermal deterioration to new ECM (Click here).


NEXT


20. CHECK IF DTC OUTPUT
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P1601
    A
    Not P1601
    B



A
Go to step 19
B

END

21. CLEAR CATALYST RECORD
  1. Clear the catalyst record of DPNR thermal deterioration (Click here).


NEXT

END

22. REGISTER INJECTOR COMPENSATION CODE
  1. Input the injector compensation codes (Click here).

    HINT:
    1. If DTC P1601 was output in the previously installed ECM, input the injector code written on the injector in the new ECM.
    2. If DTC P1601 was not output in the previously installed ECM, input the injector code registered in the previously installed ECM to the new ECM.


NEXT


23. CHECK IF DTC OUTPUT
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P1601
    A
    Not P1601
    B



A
REGISTER INJECTOR COMPENSATION CODE
B

END


← P1550 Battery Current Sensor Circuit (+ P1551, P1552) (from Jan 2007)P1601 EEPROM Error - Injector Correction Value, DPF Thermal Degradation Record (from Jan 2007) →