2005-2008 RAV4 · Service Manual ENGINE

VC Output Circuit

Circuit diagnosis · Vehicles built from Jan 2007

DESCRIPTION

The ECM constantly generates 5 V power from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
A116143E07
When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:
Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned on (IG). The MIL goes off when the engine is started.


WIRING DIAGRAM

A159653E01
A130188E01

INSPECTION PROCEDURE


1. CHECK MIL CONDITION
  1. Check that Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch on (IG).

    OK:
    MIL lights up



OK
SYSTEM IS OK
NG


2. CHECK CONNECTION BETWEEN INTELLIGENT TESTER AND ECM
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Check the communication between the tester and ECM.

    Result:
    Result
    Proceed to
    Communication is possible
    A
    Communication is not possible
    B



A
GO TO MIL CIRCUIT
B


3. CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
  1. Disconnect the accelerator pedal position sensor connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the accelerator pedal position sensor connector.



A
REPLACE ACCELERATOR PEDAL ASSEMBLY
B


4. CHECK MIL (BATTERY CURRENT SENSOR)
  1. Disconnect the battery current sensor connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the battery current sensor connector.



A
REPLACE BATTERY CURRENT SENSOR ASSEMBLY
B


5. CHECK MIL (FUEL PRESSURE SENSOR)
  1. Disconnect the fuel pressure sensor connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the fuel pressure sensor connector.



A
REPLACE COMMON RAIL ASSEMBLY
B


6. CHECK MIL (EGR VALVE POSITION SENSOR)
  1. Disconnect the EGR valve position sensor connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the EGR valve position sensor connector.



A
REPLACE EGR VALVE ASSEMBLY
B


7. CHECK MIL (THROTTLE POSITION SENSOR)
  1. Disconnect the throttle position sensor connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the throttle position sensor connector.



A
REPLACE THROTTLE BODY ASSEMBLY
B


8. CHECK MIL (DIFFERENTIAL PRESSURE SENSOR)
  1. Disconnect the different pressure sensor connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the different pressure sensor connector.



A
REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY
B


9. CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the manifold absolute pressure sensor connector.



A
REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
B


10. CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GND IN EACH SENSOR)
  1. Disconnect the accelerator pedal position sensor connector.

  1. Disconnect the battery current sensor connector.

  1. Disconnect the fuel pressure sensor connector.

  1. Disconnect the EGR valve position sensor connector.

  1. Disconnect the throttle position sensor connector.

  1. Disconnect the different pressure sensor connector.

  1. Disconnect the manifold absolute pressure sensor connector.

  1. A130158E08
    Disconnect the ECM connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A12-55 (VCPA) - Body ground
    10 kΩ or higher
    A12-56 (VCP2) - Body ground
    10 kΩ or higher
    B32-70 (VCIB) - Body ground
    10 kΩ or higher
    B32-69 (VCM) - Body ground
    10 kΩ or higher
    B32-72 (VCEG) - Body ground
    10 kΩ or higher
    B32-73 (VCVL) - Body ground
    10 kΩ or higher
    B32-74 (VCPX) - Body ground
    10 kΩ or higher
    B32-71 (VCPM) - Body ground
    10 kΩ or higher

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the battery current sensor connector.

  1. Reconnect the fuel pressure sensor connector.

  1. Reconnect the EGR valve position sensor connector.

  1. Reconnect the throttle position sensor connector.

  1. Reconnect the different pressure sensor connector.

  1. Reconnect the manifold absolute pressure sensor connector.

  1. Reconnect the ECM connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← ECM Power Source Circuit (from Aug 2007)Cranking Holding Function Circuit (Jan 2007 – Jul 2007) →