2005-2008 RAV4 · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built Jan 2007 – Jul 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. INSTALL CLUTCH MASTER CYLINDER ASSEMBLY
  1. Install the clutch master cylinder with the 2 nuts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 in.*lbf }


2. CONNECT CLUTCH MASTER CYLINDER TO FLEXIBLE HOSE TUBE

C127491
  1. Using SST, connect the flexible hose tube.

    SST
    09023-00101  

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf } for use without SST
    14 N*m{ 143 kgf*cm , 10 ft.*lbf } for use with SST

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).


3. CONNECT CLUTCH RESERVOIR TUBE

C127490
  1. Connect the clutch reservoir tube to the clutch master cylinder with the clip.

    NOTICE:
    1. Connect the clutch reservoir tube so that it will not be twisted.
    2. Face the white mark upward.


4. CONNECT CLUTCH MASTER CYLINDER PUSH ROD CLEVIS

C132127
  1. Apply MP grease to the contact surface of the pin and clevis bush.

  1. Connect the clevis to the clutch pedal with the pin and clip.

    HINT:
    Install the pin from the left side of the vehicle.

  1. Install the clip to the pin.


5. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Knee Airbag)

B127987
  1. Connect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Install the driver side knee airbag with the 4 bolts.

    Torque:
    10 N*m{ 101 kgf*cm , 7 ft.*lbf }


6. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (w/o Knee Airbag)

B132919
  1. Attach the 8 claws to install the lower instrument panel finish panel.

  1. Install the 2 screws.


7. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

B129996
  1. Attach the 2 claws to install the instrument panel under cover.

  1. Install the 2 screws.


8. INSTALL COWL BODY MOUNTING REINFORCEMENT LH

B134569E01
  1. Install the mounting reinforcement with the 2 nuts.


9. INSTALL COWL TOP PANEL OUTER SUB-ASSEMBLY

B134568
  1. Install the cowl top panel outer with the 14 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }


10. INSTALL COWL VENTILATOR HOUSING SUB-ASSEMBLY

B134570
  1. Attach the claws to install ventilator housing.


11. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

B133583
  1. Connect the connector and attach the clamp.

  1. Move the wiper motor and link in the direction shown by the arrow in the illustration to attach the wiper cushion to the body, and install the wiper motor and link.

  1. Install the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


12. INSTALL COWL TOP VENTILATOR LOUVER

B131453
  1. Attach the 12 claws and install the louver.

  1. Install the 2 clips.


13. INSTALL FRONT FENDER TO COWL SIDE SEAL LH

E125248E01
  1. Attach the claw to install the front fender to cowl side seal.


14. INSTALL FRONT FENDER TO COWL SIDE SEAL RH

B133588
  1. Attach the claw to install the front fender to cowl side seal.


15. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

  1. E058837E07
    Clean the wiper arm serration with a round file or equivalent.

  1. Clean the wiper pivot serration with a wire brush.

  1. B133594E01
    Install the arm and blade with the nut. Make sure that the arm and blade comes to the position shown in the illustration.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

    HINT:
    Hold down the arm hinge with your hand while tightening the nut.

  1. Operate the front wipers while spraying water or washer fluid on the windshield. Ensure that there is no interference between the blades and pillar.


16. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

  1. E058837E07
    Stop the wiper motor at the automatic stop position.

  1. Clean the wiper arm serration with a round file or equivalent.

  1. Clean the wiper pivot serration with a wire brush.

  1. B133593E01
    Install the arm and blade with the nut. Make sure that the arm and blade comes to the position shown in the illustration.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

    HINT:
    Hold down the arm hinge with your hand while tightening the nut.


17. INSTALL FRONT WIPER ARM HEAD CAP
  1. Install the 2 caps.


18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

19. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).


20. BLEED CLUTCH PIPE LINE
  1. Fill the brake reservoir with brake fluid and bleed the clutch system.

    Torque:
    8.3 N*m{ 85 kgf*cm , 74 in.*lbf }


21. CHECK BRAKE FLUID
  1. Check the brake fluid (Click here).

    HINT:
    1. Check for leakage in the brake system.
    2. Check for leakage in the clutch system.


22. CHECK FLUID LEVEL IN RESERVOIR

C126431
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

    HINT:
    Add fluid to a level between the reservoir's MIN and MAX lines.


23. INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY
  1. Lift up the floor carpet to expose the asphalt sheet under the pedal.

  1. C125490E01
    Check that the pedal height is correct.

    Standard pedal height from dash panel:
    169.2 to 172.9 mm (6.661 to 6.807 in.)
    for 1AZ-FE
    173.9 to 183.9 mm (6.846 to 7.240 in.)
    for 2AZ-FE
    176.5 to 186.5 mm (6.949 to 7.343 in.)
    for 2AD-FTV, 2AD-FHV

  1. Adjust the pedal height.

    1. Loosen the lock nut and turn the stopper bolt until the pedal height is within the specified range.

    2. Tighten the lock nut.

      Torque:
      16 N*m{ 163 kgf*cm , 12 ft.*lbf }

  1. C133426E01
    Check the pedal free play and push rod play.

    1. Depress the clutch pedal until resistance is felt.

    2. Measure the distance between the pedal's released position and the position in the previous step.

      Standard pedal free play:
      5.0 to 15.0 mm (0.197 to 0.591 in.)

    3. Release the pedal. Using your finger, gently press the pedal until resistance increases slightly.

    4. Measure the distance between the pedal's released position and the position in the previous step.

      Standard push rod play at pedal top:
      1.0 to 5.0 mm (0.039 to 0.197 in.)

  1. Adjust the pedal free play and push rod play.

    1. Loosen the lock nut and turn the push rod until the pedal free play and push rod play are within the specified ranges.

    2. Tighten the lock nut.

      Torque:
      12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    3. Check the pedal height.

  1. C125492E01
    Check the clutch release point.

    1. Pull the parking brake lever and use wheel chocks to stabilize the vehicle.

    2. Start the engine and run it at idle.

    3. Without depressing the clutch pedal, slowly move the shift lever to R until the gears contact.

    4. Gently depress the clutch pedal and measure the stroke distance from the point that the gear noise stops (release point) to the full stroke end position.

      Standard distance:
      25 mm (0.98 in.) or more

      If the distance is not as specified, perform the following operations.
      1. Check pedal height.
      1. Check push rod play and pedal free play.
      1. Bleed air from clutch line.
      1. Check clutch cover and disc.

← INSTALLATION (Nov 2005 – Dec 2006)INSTALLATION (from Aug 2007) →