Fuel Pump Control Circuit
Circuit diagnosis · Vehicles built from Nov 2005
DESCRIPTION
When the engine is cranked, the starter relay drive signal output from the STAR terminal of the ECM is input into the STA terminal of the ECM, and NE signal generated by the crankshaft position sensor is also input into the NE+ terminal. Thus, the ECM interprets that the engine is cranked, and turns the transistor Tr1 in the ECM internal circuit ON. The current flows to the C/OPN (Circuit Opening) relay by turning the Tr1 ON. Then, the fuel pump operates.While the NE signal is input into the ECM, when the engine is running, the ECM turns the Tr1 on continuously.


WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVE THE FUEL PUMP SPEED CONTROL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check whether the fuel pump operating sound occurs when performing the Active Test on the tester.
- OK:
- Fuel pump operating sound occurs.
|
|
||||
| NG | |
| 2. INSPECT MAIN BODY ECU (C/OPN RELAY INPUT VOLTAGE) |
Measure the voltage between the terminal of the main body ECU (instrument panel junction block) and the body ground when the ignition switch is turned on (IG) and off.

- Standard voltage:
Tester Connection
Ignition Switch Condition
Specified Condition
IB-11 - Body ground
off
Below 1 V
IF-4 - Body ground
IB-11 - Body ground
on (IG)
9 to 14 V
IF-4 - Body ground
|
|
||||
| NG | |
| 3. CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK - MAIN BODY ECU, MAIN BODY ECU - INTEGRATION RELAY) |
Remove the IG2 relay from the engine room No. 1 relay block.
Remove the integration relay from the engine room No. 1 relay block (R/B).
Disconnect the IB and IF connectors from the main body ECU (instrument panel junction block).
Measure the resistance.

- Standard resistance (Check for open):
Tester Connection
Specified Condition
Relay Block IG2 relay block terminal (5) - IF-4
Below 1 Ω
Relay Block (1A-4) - IB-11
Below 1 Ω
- Standard resistance (Check for short):
Tester Connection
Specified Condition
IF-4 - Body ground
10 kΩor higher
IB-11 - Body ground
10 kΩor higher
Reinstall the IG2 relay.
Reinstall the integration relay.
Reconnect the main body ECU (instrument panel junction block) connectors.
|
|
||||
| OK | ||
| ||
| 4. INSPECT MAIN BODY ECU (C/OPN RELAY) |
Remove the main body ECU (instrument panel junction block).

Measure the C/OPN relay resistance.
- Standard resistance:
Tester Connection
Specified Condition
IB-11 - IA-8
10 kΩ or higher
Below 1 Ω
(when battery voltage is applied to terminals IB-9 and IE-5)
- HINT:
- Relay coil circuit between IB-9 and IE-5 is not through IGN fuse.
Reinstall the main body ECU (instrument panel junction block).
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ECM) |
Disconnect the A12 ECM connector.

Disconnect the IE connector from main body ECU (instrument panel junction block).
Measure the resistance.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
IE-5 - FC (A12-7)
Below 1Ω
- Standard resistance (Check for short):
Tester Connection
Specified Condition
IE-5 or FC (A12-7) - Body ground
10 kΩ or higher
Reconnect the main body ECU (instrument panel junction block) and the ECM connectors.
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (C/OPN RELAY - FUEL PUMP - BODY GROUND) |
Check the harness and the connectors between the main body ECU (instrument panel junction block) and the fuel pump.

Disconnect the IA connector from main body ECU (instrument panel junction block).
Disconnect the T1 fuel pump connector.
Measure the resistance.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
IA-8 - Fuel pump (T1-4)
Below 1Ω
- Standard resistance (Check for short):
Tester Connection
Specified Condition
IA-8 or Fuel pump (T1-4) - Body ground
10 kΩ or higher
Check the harness and the connectors between the fuel pump and the body ground.
Disconnect the T1 fuel pump connector.
Measure the resistance.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
Fuel pump (T1-5) - Body ground
Below 1 Ω
Reconnect the Main body ECU (instrument panel junction block) connector.
Reconnect the fuel pump connector.
|
|
||||
| OK | |
| 7. INSPECT FUEL PUMP |
Inspect fuel pump resistance.

Measure the resistance between the terminals.
- Standard resistance:
- 0.2 to 3.0 Ω at 20°C(68°F)
Inspect fuel pump operation.
Apply the battery voltage to both the terminals.
Check that the pump operates.
- NOTICE:
- These tests must be done quickly (within 10 seconds) to prevent the coil from burning out.
- Keep the fuel pump as far away from the battery as possible.
- Always turn the voltage on and off on the battery side, not the fuel pump side.
- These tests must be done quickly (within 10 seconds) to prevent the coil from burning out.
|
|
||||
| OK | ||
| ||
| 8. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.
Check the result when the ignition switch is turned on (IG) and START.
- OK:
Ignition Switch Position
Starter Signal
ON
OFF
START
ON
|
|
||||
| OK | |
| 9. READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Engine Speed.
Read the values displayed on the tester while cranking.
- OK:
- Values are displayed continuously.
|
|
||||
| OK | ||
| ||
