Cranking Holding Function Circuit
Circuit diagnosis · Vehicles built from Nov 2005
DESCRIPTION
The cranking holding control system keeps energizing the ST relay after the ECM detects the starter signal (STSW signal) from the main body ECU until the ECM performs a judgment of "Engine started". Furthermore, the ECM outputs an accessory cut signal (ACCR signal) to the ACC relay during cranking to prevent flickering of the combination meter, clock, audio system, and so on.When the ECM detects the STSW signal, the ECM outputs the starter relay drive signal (STAR signal) to the starter relay through the clutch start switch or park / neutral position switch, and then, the engine is cranked. When the ECM receives a stable engine speed signal (NE signal), more specifically, when the NE signal reaches a predetermined value, the ECM stops outputting the STAR signal. Also, the ECM monitors the ST relay operating conditions based on the STA terminal voltage status.


WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.
Check the result when the ignition switch is turned on (IG).
Check the result when the engine starts.
- Standard:
Ignition Switch Condition
Tester Display (Starter Signal)
on (IG)
OFF
Engine starts
ON
|
|
||||
| NG | |
| 2. INSPECT ECM (STSW TERMINAL VOLTAGE) |
![]() ![]() |
Disconnect the A12 ECM connector.
Depress the clutch pedal fully (for M/T models).
Shift lever is P position (for A/T models).
Measure the voltage between the ECM terminal and the body ground when operating the ignition switch to start cranking.
- Standard voltage:
Tester Connection
Specified Condition
STSW (A12-14) - Body ground
10 to 14 V
Reconnect the ECM connector.
|
|
||||
| OK | |
| 3. INSPECT ECM (STAR OUTPUT VOLTAGE) |
Disconnect the A4 clutch start switch connector (for M/T models).

Disconnect the B28 Park / Neutral Position (PNP) switch connector (for A/T models)

Measure the voltage between the terminal of clutch start switch or PNP switch connector and the body ground while cranking the engine.
- Standard voltage:
M/T Tester Connection
Specified Condition
B (A4-2) - Body ground
10 to 14 V
- A/T:
Tester Connection
Specified Condition
B (B28-4) - Body ground
10 to 14 V
Reconnect the clutch start switch connector.
Reconnect the PNP switch connector.
|
|
||||
| OK | |
| 4. INSPECT CLUTCH START SWITCH ASSEMBLY OR PARK / NEUTRAL POSITION SWITCH ASSEMBLY |
M/T:
Disconnect the A4 clutch start switch connector.
Measure the resistance between the terminals of the clutch start switch assembly connector.

- Standard resistance:
Switch Condition
Specified Condition
Pushed in
Below 1 Ω
Released
10 kΩ or higher
A/T:
Disconnect the B28 PNP switch connector.
Measure the resistance between each terminal shown below when the shift lever is moved to each range.

- Standard resistance:
Shift Position
Tester Connection
Specified Condition
P
PL (6) - RB (2)
Below 1 Ω
L (5) - B (4)
R
RL (1) - RB (2)
N
NL (9) - RB (2)
L (5) - B (4)
D
DL (7) - RB (2)
2
2L (3) - RB (2)
L
LL (8) - RB (2)
|
|
||||
| NG | ||
| ||
| 5. CHECK HARNESS AND CONNECTOR (ECM - MAIN BODY ECU) |
![]() ![]() |
Disconnect the E20 main body ECU connector.
Disconnect the A12 ECM connector.
Measure the resistance.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
STSW (E20-4) - STSW (A12-14)
Below 1 Ω
- Standard resistance (Check for short):
Tester Connection
Specified Condition
STSW (E20-4) - Body ground
Below 1 Ω
Reconnect the main body ECU connector.
Reconnect the ECM connector.
|
|
||||
| OK | ||
| ||
| 6. INSPECT ST CUT RELAY |
![]() ![]() |
Remove the ST CUT relay from the No. 7 relay block.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
3 - 5
10 kΩ or higher
3 - 5
Below 1 Ω
(When battery voltage applied to terminals 1 and 2)
Reinstall the relay.
|
|
||||
| OK | |
| 7. INSPECT NO. 7 RELAY BLOCK (RELAY HOLDER TERMINAL VOLTAGE) |
![]() ![]() |
Remove the ST CUT relay from the No. 7 relay block.
Turn the ignition switch on (IG).
Measure the voltage between the terminals of the ST CUT relay holder.
- Standard voltage:
Tester Connection
Specified Condition
1 - 2
10 to 14 V
Reinstall the relay.
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (ECM - CLUTCH START SWITCH OR PARK / NEUTRAL POSITION SWITCH ASSEMBLY - MAIN BODY ECU) |
![]() ![]() |
Remove the ST CUT relay from the No. 7 relay block.
Disconnect the A4 clutch start switch assembly connector (for M/T models).
Disconnect the B28 PNP switch assembly connector (for A/T models).
Disconnect the E20 main body ECU connector.
Disconnect the B32 ECM connector.
Measure the resistance.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
ST CUT relay (3) - STAR (B32-52)
Below 1 Ω
ST CUT relay (3) - STR2 (E20-14)
Below 1 Ω
STR (E20-3) - ST CUT relay (5)
Below 1 Ω
B (A4-2)*1 - ST CUT relay (5)
Below 1 Ω
B (B28-4)*2 - ST CUT relay (5)
Below 1 Ω
- HINT:
- *1: M/T
- *2: A/T
- *1: M/T
- Standard resistance (Check for short):
Tester Connection
Specified Condition
ST CUT relay (3) - Body ground
10 kΩ or higher
ST CUT relay (5) - Body ground
10 kΩ or higher
Reconnect the ECM connector.
Reconnect the main body ECU connector.
Reconnect the clutch start switch assembly connector.
Reconnect the PNP switch assembly connector.
Reinstall the ST CUT relay.
|
|
||||
| OK | |
| 9. INSPECT NO. 7 RELAY BLOCK (CHECK FOR SHORT) |
![]() ![]() |
Disconnect the ECM connector.
Remove the ST CUT relay from the No. 7 relay block.
Measure the resistance between the terminals of the ST CUT relay holder.
- Standard resistance (Check for short):
Tester Connection
Specified Condition
No. 7 Relay block ST CUT relay (3) - Body ground
10 kΩ or higher
No. 7 Relay block ST CUT relay (5) - Body ground
10 kΩ or higher
Reinstall the ST CUT relay.
Reconnect the ECM connector.
|
|
||||
| OK | ||
| ||
| 10. CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH OR PARK / NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ST RELAY) |
![]() ![]() |
Remove the ST relay from the No. 8 relay block.
Disconnect the A4 clutch start switch assembly connector (for M/T models).
Disconnect the B28 PNP switch assembly connector (for A/T models).
Disconnect the A12 ECM connector.
Measure the resistance.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
L (A4-1)*1 - STA (A12-48)
Below 1 Ω
L (A4-1)*1 - ST relay (1)
Below 1 Ω
L (B28-5)*2 - STA (A12-48)
Below 1 Ω
L (B28-5)*2 - ST relay (1)
Below 1 Ω
ST relay (2) - Body ground
Below 1 Ω
- HINT:
- *1: M/T
- *2: A/T
- *1: M/T
- Standard resistance (Check for short):
Tester Connection
Specified Condition
L (A4-1)*1 - Body ground
10 kΩ or higher
L (B28-5)*2 - Body ground
10 kΩ or higher
- HINT:
- *1: M/T
- *2: A/T
- *1: M/T
Reinstall the ST relay.
Reconnect the clutch start switch connector.
Reconnect the PNP switch assembly connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 11. INSPECT BATTERY |
Check that the battery is not depleted.
- OK:
- Battery is not depleted.
|
|
||||
| OK | |
| 12. CHECK BATTERY TERMINAL |
Check that the battery terminals are not loose or corroded.
- OK:
- Battery terminals are not loose or corroded.
|
|
||||
| OK | ||
| ||






