2005-2008 RAV4 · Service Manual ENGINE

Cranking Holding Function Circuit

Circuit diagnosis · Vehicles built from Nov 2005

DESCRIPTION

The cranking holding control system keeps energizing the ST relay after the ECM detects the starter signal (STSW signal) from the main body ECU until the ECM performs a judgment of "Engine started". Furthermore, the ECM outputs an accessory cut signal (ACCR signal) to the ACC relay during cranking to prevent flickering of the combination meter, clock, audio system, and other areas.
When the ECM detects the STSW signal, the ECM outputs the starter relay drive signal (STAR signal) to the starter relay through the clutch start switch, and then the engine is cranked. When the ECM receives a stable engine speed signal (NE signal) (more specifically, when the NE signal reaches a predetermined value), the ECM stops outputting the STAR signal. Also, the ECM monitors the ST relay operating conditions based on the STA terminal voltage status.
A103821E17

WIRING DIAGRAM

A130167E01

INSPECTION PROCEDURE

NOTICE:
Perform electronic throttle learning after replacing the ECM (Click here).


1. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the result when the ignition switch is turned on (IG).

  1. Check the result when the engine starts.

    OK:
    Ignition Switch Condition
    Tester Display (Starter Signal)
    On (IG)
    OFF
    Engine starts
    ON



OK
Go to step 10
NG


2. CHECK ECM (STSW TERMINAL VOLTAGE)
A115671E14
  1. Disconnect the A12 ECM connector.

  1. Depress the clutch pedal fully.

  1. Measure the voltage of the ECM terminal and the body ground when operating the ignition switch to start cranking.

    Standard voltage:
    Tester Connection
    Specified Condition
    A12-9 (STSW) - Body ground
    10 to 14 V

  1. Reconnect the ECM connector.



NG
Go to step 5
OK


3. CHECK ECM (STAR OUTPUT VOLTAGE)

  1. A131571E01
    Disconnect the A4 clutch start switch connector.

  1. Measure the voltage of the terminal of clutch start switch connector and the body ground while cranking the engine.

    Standard voltage:
    Tester Connection
    Specified Condition
    A4-2 - Body ground
    10 to 14 V

  1. Reconnect the clutch start switch connector.



NG
Go to step 6
OK


4. INSPECT CLUTCH START SWITCH
A131572E01
  1. Disconnect the A4 clutch start switch connector.

  1. Measure the resistance of the terminals of the clutch start switch connector.

    Standard resistance:
    Switch Condition
    Specified Condition
    Pushed
    Below 1 Ω
    Not pushed
    10 kΩ or higher

  1. Reconnect the clutch start switch connector.



OK
Go to step 10
NG

REPLACE CLUTCH START SWITCH

5. CHECK WIRE HARNESS (ECM - MAIN BODY ECU)
A127899E02
  1. Disconnect the E20 main body ECU connector.

  1. Disconnect the A12 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    E20-4 (STSW) - A12-9 (STSW )
    Below 1 Ω
    E20-4 (STSW) - Body ground
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

CHECK ENTRY AND START SYSTEM

6. INSPECT ST CUT RELAY
B060778E30
  1. Remove the ST CUT relay from the No. 7 relay block.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (When battery voltage applied to terminals 1 and 2)

  1. Reinstall the relay.



NG
REPLACE ST CUT RELAY
OK


7. CHECK ST CUT RELAY (RELAY HOLDER TERMINAL VOLTAGE)
A130178E01
  1. Remove the ST CUT relay from the No. 7 relay block.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage of the terminals of the ST CUT relay holder.

    Standard voltage:
    Tester Connection
    Specified Condition
    1 - 2
    10 to 14 V

  1. Reinstall the relay.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


8. CHECK WIRE HARNESS (ECM - CLUTCH START SWITCH - MAIN BODY ECU)
A130165E01
  1. Remove the ST CUT relay from the No. 7 relay block.

  1. Disconnect the A4 clutch start switch connector.

  1. Disconnect the E20 main body ECU connector.

  1. Disconnect the B32 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    ST CUT relay terminal 3 - B32-53 (STAR)
    Below 1 Ω
    ST CUT relay terminal 3 - E20-14 (STR2)
    Below 1 Ω
    E20-3 (STR) - ST CUT relay terminal 5
    Below 1 Ω
    A4-2 - ST CUT relay terminal 5
    Below 1 Ω
    ST CUT relay terminal 3 - Body ground
    10 kΩ or higher
    ST CUT relay terminal 5 - Body ground
    10 kΩ or higher

  1. Reinstall the ST CUT relay.

  1. Reconnect the clutch start switch connector.

  1. Reconnect the main body ECU connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


9. CHECK NO. 7 RELAY BLOCK (CHECK FOR SHORT)
A130178E01
  1. Remove the ST CUT relay from the No. 7 relay block.

  1. Disconnect the B32 ECM connector.

  1. Measure the resistance of the terminals of the ST CUT relay holder.

    Standard resistance:
    Tester Connection
    Specified Condition
    No. 7 Relay block ST CUT relay terminal 3 - Body ground
    10 kΩ or higher
    No. 7 Relay block ST CUT relay terminal 5 - Body ground
    10 kΩ or higher

  1. Reinstall the ST CUT relay.

  1. Reconnect the ECM connector.



NG
CHECK ENTRY AND START SYSTEM
OK

REPLACE ECM

10. CHECK WIRE HARNESS (CLUTCH START SWITCH - ECM - ST RELAY)
A130166E01
  1. Remove the ST relay from the No. 8 relay block.

  1. Disconnect the A4 clutch start switch connector.

  1. Disconnect the A12 ECM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    A4-1 - A12-43 (STA)
    Below 1 Ω
    A4-1 - ST relay terminal 1
    Below 1 Ω
    ST relay terminal 2 - Body ground
    Below 1 Ω
    A4-1 - Body ground
    10 kΩ or higher

  1. Reinstall the ST relay.

  1. Reconnect the clutch start switch connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


11. INSPECT BATTERY
  1. Check that the battery is not depleted.

    OK:
    Battery is not depleted.



NG
REPLACE BATTERY
OK


12. CHECK BATTERY TERMINAL
  1. Check that the battery terminals are not loose or corroded.

    OK:
    Battery terminals are not loose or corroded.



NG
REPAIR OR REPLACE BATTERY TERMINAL
OK

CHECK AND REPLACE STARTER POWER SOURCE CIRCUIT


← VC Output Circuit (from Nov 2005)MIL Circuit (Nov 2005 – Dec 2006) →