Cranking Holding Function Circuit
Circuit diagnosis · Vehicles built from Aug 2007
Versions by build date: Jan 2007 – Jul 2007 from Aug 2007
DESCRIPTION
The cranking holding control system keeps energizing the ST relay after the ECM detects the starter signal (STSW signal) from the main body ECU until the ECM performs a judgment of "Engine started". Furthermore, the ECM outputs an accessory cut signal (ACCR signal) to the ACC relay during cranking to prevent flickering of the combination meter, clock, audio system, and other areas.When the ECM detects the STSW signal, the ECM outputs the starter relay drive signal (STAR signal) to the starter relay through the clutch start switch, and then the engine is cranked. When the ECM receives a stable engine speed signal (NE signal) (more specifically, when the NE signal reaches a predetermined value), the ECM stops outputting the STAR signal. Also, the ECM monitors the ST relay operating conditions based on the STA terminal voltage status.


WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
| 1. READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Enter the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.
Check the result when the ignition switch is turned on (IG).
Check the result when the engine starts.
- OK:
Ignition Switch Condition
Tester Display (Starter Signal)
On (IG)
OFF
Engine starts
ON
|
|
||||
| NG | |
| 2. CHECK ECM (STSW TERMINAL VOLTAGE) |
Disconnect the ECM connector.

Depress the clutch pedal fully.
Measure the voltage of the ECM terminal and the body ground when operating the ignition switch to start cranking.
- Standard voltage:
Tester Connection
Specified Condition
A12-9 (STSW) - Body ground
10 to 14 V
Reconnect the ECM connector.
|
|
||||
| OK | |
| 3. CHECK ECM (STAR OUTPUT VOLTAGE) |
Disconnect the clutch start switch connector.

Measure the voltage of the terminal of clutch start switch connector and the body ground while cranking the engine.
- Standard voltage:
Tester Connection
Specified Condition
A4-2 - Body ground
10 to 14 V
Reconnect the clutch start switch connector.
|
|
||||
| OK | |
| 4. INSPECT CLUTCH START SWITCH |
Disconnect the clutch start switch connector.

Measure the resistance of the terminals of the clutch start switch connector.
- Standard resistance:
Switch Condition
Specified Condition
Pushed
Below 1 Ω
Not pushed
10 kΩ or higher
Reconnect the clutch start switch connector.
|
|
||||
| NG | ||
| ||
| 5. CHECK HARNESS AND CONNECTOR (ECM - MAIN BODY ECU) |
Disconnect the main body ECU connector.

Disconnect the ECM connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
E20-4 (STSW) - A12-9 (STSW)
Below 1 Ω
E20-4 (STSW) - Body ground
10 kΩ or higher
Reconnect the main body ECU connector.
Reconnect the ECM connector.
|
|
||||
| OK | ||
| ||
| 6. INSPECT ST CUT RELAY |
Remove the ST CUT relay from the No. 7 relay block.

Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
3 - 5
10 kΩ or higher
3 - 5
Below 1 Ω
(When battery voltage applied to terminals 1 and 2)
Reinstall the relay.
|
|
||||
| OK | |
| 7. CHECK ST CUT RELAY (RELAY HOLDER TERMINAL VOLTAGE) |
Remove the ST CUT relay from the No. 7 relay block.

Turn the ignition switch on (IG).
Measure the voltage of the terminals of the ST CUT relay holder.
- Standard voltage:
Tester Connection
Specified Condition
1 - 2
10 to 14 V
Reinstall the relay.
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (ECM - CLUTCH START SWITCH - MAIN BODY ECU) |
Remove the ST CUT relay from the No. 7 relay block.

Disconnect the clutch start switch connector.
Disconnect the main body ECU connector.
Disconnect the ECM connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
ST CUT relay terminal 3 - B32-53 (STAR)
Below 1 Ω
ST CUT relay terminal 3 - E20-14 (STR2)
Below 1 Ω
E20-3 (STR) - ST CUT relay terminal 5
Below 1 Ω
A4-2 - ST CUT relay terminal 5
Below 1 Ω
ST CUT relay terminal 3 - Body ground
10 kΩ or higher
ST CUT relay terminal 5 - Body ground
10 kΩ or higher
Reinstall the ST CUT relay.
Reconnect the clutch start switch connector.
Reconnect the main body ECU connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 9. CHECK NO. 7 RELAY BLOCK (CHECK FOR SHORT) |
Remove the ST CUT relay from the No. 7 relay block.

Disconnect the ECM connector.
Measure the resistance of the terminals of the ST CUT relay holder.
- Standard resistance:
Tester Connection
Specified Condition
No. 7 Relay block ST CUT relay terminal 3 - Body ground
10 kΩ or higher
No. 7 Relay block ST CUT relay terminal 5 - Body ground
10 kΩ or higher
Reinstall the ST CUT relay.
Reconnect the ECM connector.
|
|
||||
| OK | ||
| ||
| 10. CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH - ST RELAY) |
Remove the ST relay from the No. 8 relay block (RHD) or No. 7 relay block (LHD).

Disconnect the clutch start switch connector.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
A4-1 - ST relay terminal 1
Below 1 Ω
ST relay terminal 2 - Body ground
Below 1 Ω
A4-1 - Body ground
10 kΩ or higher
Reinstall the ST relay.
Reconnect the clutch start switch connector.
|
|
||||
| OK | |
| 11. INSPECT BATTERY |
Check that the battery is not depleted.
- OK:
- Battery is not depleted.
|
|
||||
| OK | |
| 12. CHECK BATTERY TERMINAL |
Check that the battery terminals are not loose or corroded.
- OK:
- Battery terminals are not loose or corroded.
|
|
||||
| OK | ||
| ||
