REMOVAL
Removal / installation · Vehicles built Nov 2005 – Dec 2006
Versions by build date: Nov 2005 – Dec 2006 from Jan 2007
- HINT:
- Use the same procedures for the RH side and LH side.
- The procedures listed below are for the LH side.
| 1.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
 |
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
| 2.
REMOVE REAR DOOR SCUFF PLATE LH (for Short Body)
|
 |
- Using a screwdriver, detach the 8 claws and remove the scuff plate.
- HINT:
- Tape the screwdriver tip before use.
| 3.
REMOVE REAR DOOR SCUFF PLATE LH (for Long Body)
|
 |
Using a screwdriver, detach the 9 claws.
- HINT:
- Tape the screwdriver tip before use.
Using a clip remover, detach the 2 clips and remove the garnish.
| 4.
REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH |
|
| 5.
REMOVE PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY |
|
| 6.
REMOVE TONNEAU COVER ASSEMBLY |
|
| 7.
REMOVE REAR FLOOR NO. 1 BOARD |
|
| 8.
REMOVE DECK BOARD ASSEMBLY |
|
| 9.
REMOVE REAR FLOOR NO. 2 BOARD |
|
| 10.
REMOVE REAR FLOOR NO. 3 BOARD |
|
| 11.
REMOVE JACK CARRIER ASSEMBLY (for Short Body)
|
 |
Using a clip remover, remove the 7 clips and remove the jack carrier.
| 12.
REMOVE REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE
|
 |
Remove the 4 screws.
Using a clip remover, detach the 7 clips and remove the plate.
| 13.
REMOVE BACK DOOR WEATHERSTRIP |
|
| 14.
REMOVE REAR FLOOR FINISH PLATE (for Short Body)
|
 |
- Using a clip remover, detach the 6 clips and remove the finish plate.
| 15.
REMOVE REAR FLOOR FINISH PLATE (for Long Body)
|
 |
Using a clip remover, detach the 6 clips.
Detach the 2 claws and remove the finish plate.
| 16.
REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH |
|
| 17.
REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR COVER (for Short Body) |
|
| 18.
REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR BRACKET (for Short Body) |
|
| 19.
DISCONNECT REAR NO. 1 SEAT BELT ASSEMBLY OUTER RH |
 |
Remove the lap belt outer anchor cover.
Remove the bolt and disconnect the floor anchor.
| 20.
REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for Short Body)
|
 |
- Disconnect the rear No. 1 seat belt's floor anchor.
Remove the anchor cover.
Remove the bolt and disconnect the floor anchor.
- Remove the bolt and 2 screws.
Using a screwdriver, detach the 5 claws.
- HINT:
- Tape the screwdriver tip before use.
Using a clip remover, detach the 5 clips and remove the trim board.
Disconnect the power outlet socket connector.
Remove the belt hanger.
| 21.
REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for Long Body)
|
 |
- Disconnect the rear No.1 seat outer belt's floor anchor.
Remove the anchor cover.
Remove the bolt and disconnect the floor anchor.
- Remove the 2 screws and 2 bolts.
Using a screwdriver, detach the 5 claws.
- HINT:
- Tape the screwdriver tip before use.
Using a clip remover, detach the 4 clips and remove the trim board.
Disconnect the power outlet socket connector.
Remove the belt hanger.
| 22.
REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH (for Short Body)
|
 |
- Using a clip remover, detach the 7 clips and remove the garnish.
| 23.
REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH (for Long Body)
|
 |
- Using a clip remover, detach the 7 clips and remove the garnish.
| 24.
REMOVE REAR NO. 1 SEAT BELT ASSEMBLY OUTER LH |
 |
Remove the bolt and disconnect the seat belt's shoulder anchor.
- Remove the 2 bolts and seat belt.