2005-2008 RAV4 · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built from Aug 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. INSTALL BRAKE PEDAL SUPPORT ASSEMBLY

C126454
  1. Install the support with the 4 nuts.

    Torque:
    12.7 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. C129086E01
    Install the bolt to the support.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }


2. INSTALL PUSH ROD PIN

C130666E05

C130668E03
  1. Apply lithium soap base glycol grease to the push rod pin.

  1. Install the push rod pin to the push rod clevis.

    NOTICE:
    The push rod pin must be installed as shown in the illustration.

  1. Install the clip to the push rod pin.

    NOTICE:
    The clip must be installed as shown in the illustration.


3. INSTALL STOP LIGHT SWITCH ASSEMBLY

  1. C111301E03
    Insert the switch into the adjuster until the switch body touches the pedal.

    NOTICE:
    Do not depress the pedal.

  1. C111302E02
    Turn the switch a quarter turn clockwise.

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less

    NOTICE:
    Do not depress the pedal.

  1. Check the switch clearance.

    Standard stop light switch clearance:
    0.5 to 2.6 mm (0.020 to 0.102 in.)


4. CONNECT CONNECTORS
  1. with VSC:
    Connect the brake pedal load sensing switch connector.

  1. Connect the stop light switch connector.


5. CHECK AND ADJUST BRAKE PEDAL HEIGHT

  1. C129085E01
    Check the pedal height.

    Standard pedal height from dash panel:
    Model
    Specified Condition
    LHD
    184.2 to 194.2 mm (7.252 to 7.646 in.)
    RHD
    168.6 to 178.6 mm (6.638 to 7.031 in.)

  1. Adjust the pedal height.

    1. Disconnect the connector from the stop light switch.

    2. Remove the switch.

    3. Loosen the push rod clevis lock nut.

    4. Adjust the pedal height by turning the push rod.

    5. Tighten the lock nut.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }

    6. C111301E03
      Insert the switch into the adjuster until the switch body touches the pedal.

      NOTICE:
      Do not depress the pedal.

    7. C111302E02
      Turn the switch a quarter turn clockwise.

      Torque:
      1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less

      NOTICE:
      Do not depress the pedal.

    8. Connect the connector to the switch.

    9. Check the switch clearance.

      Standard stop light switch clearance:
      0.5 to 2.6 mm (0.020 to 0.102 in.)


6. CHECK BRAKE PEDAL FREE PLAY

C111306E01
  1. Stop the engine. Depress the pedal several times until there is no vacuum in the booster. Then release the pedal.

  1. Depress the pedal until resistance is felt.

  1. Check the pedal's free play by measuring the distance between the position in the previous step and the pedal's released position.

    Standard pedal free play:
    1.0 to 6.0 mm (0.039 to 0.236 in.)

    If the free play is not as specified, check the switch clearance in the next step.
    If the free play is as specified, proceed to the "CHECK BRAKE PEDAL RESERVE DISTANCE" procedure.

  1. Check the switch clearance.

    Standard stop light switch clearance:
    0.5 to 2.6 mm (0.020 to 0.102 in.)

    If the clearance is not as specified, reinstall the switch and recheck the pedal's free play.
    If the clearance is as specified, troubleshoot the brake system and proceed to the "CHECK BRAKE PEDAL RESERVE DISTANCE" procedure.


7. CHECK BRAKE PEDAL RESERVE DISTANCE

C111339E01
  1. Release the parking brake lever. Start the engine.

  1. Depress the pedal and check the pedal reserve distance.

    1. Depress the pedal with a force of 490 N (50 kgf, 110 lbf).

    2. Measure the distance between the pedal and dash panel shown in the illustration.

      Standard pedal reserve distance:
      Engine
      VSC
      LHD
      RHD
      1AZ-FE
      w/o
      More than 90 mm (3.54 in.)
      More than 80 mm (3.15 in.)
      w/
      More than 115 mm (4.53 in.)
      More than 105 mm (4.13 in.)
      2AZ-FE
      w/o
      More than 95 mm (3.74 in.)
      More than 85 mm (3.34 in.)
      w/
      More than 120 mm (4.72 in.)
      More than 110 mm (4.32 in.)
      2AD-FTV
      w/o
      More than 75 mm (2.95 in.)
      More than 70 mm (2.75 in.)
      w/
      More than 110 mm (4.33 in.)
      More than 100 mm (3.93 in.)
      2AD-FHV
      w/o
      More than 75 mm (2.95 in.)
      More than 70 mm (2.75 in.)
      w/
      More than 110 mm (4.33 in.)
      More than 100 mm (3.93 in.)
      2GR-FE
      w/
      -
      More than 110 mm (4.32 in.)

      If the distance is not as specified, troubleshoot the brake system.


8. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY
  1. Install the instrument panel (Click here).


9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
← INSTALLATION (Jan 2007 – Jul 2007)COMPONENTS (from Nov 2005) →