2005-2008 RAV4 · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built from Aug 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. INSTALL SLIDING ROOF WEATHERSTRIP

  1. Install the sliding roof weatherstrip.

    B105392E02

    1. Position the joint of the weatherstrip at the rear center.

    2. Align the marks on the weatherstrip with the middle marks at the corners of the plastic on the edge of the sliding roof panel and install the weatherstrip. Make sure that the marks on the weatherstrip are positioned within the area indicated by the marks at the corners of the plastic on the edge of the sliding roof panel.

    3. Install the lip of the weatherstrip firmly.


2. INSTALL SLIDING ROOF HOUSING ASSEMBLY

B129368
  1. Install the housing with the 4 bolts and 8 nuts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


3. CONNECT SLIDING ROOF DRAIN HOSE

B122242E02
  1. Connect the 4 drain hoses.

    NOTICE:
    The clip must face toward the outside of the vehicle and also be above the lower surface of the sliding roof housing when installing the drain hoses.


4. INSTALL SLIDING ROOF GLASS SUB-ASSEMBLY

B129372
  1. Using a T25 "TORX" driver, temporarily install the sliding roof glass sub-assembly with the 4 screws.

  1. B122199E02
    Perform a level check.

    1. Check the difference in level for "a" between the roof panel and the upper surface of the weatherstrip when the sliding roof glass is fully closed.

      Standard measurement:
      Area
      Specified Condition
      A - A
      0 + 1.5 mm (0 + 0.059 in.)
      0 - 1.5 mm (0 - 0.059 in.)
      B - B
      0 + 1.5 mm (0 + 0.059 in.)
      0 - 1.5 mm (0 - 0.059 in.)
      C - C
      0 + 1.5 mm (0 + 0.059 in.)
      0 - 1.5 mm (0 - 0.059 in.)
      D - D
      0 + 1.5 mm (0 + 0.059 in.)
      0 - 1.0 mm (0 - 0.039 in.)

      HINT:
      "+" represents the condition that the glass is above the panel level. "-" represents the condition that the glass is below the panel level.

  1. B122200E02
    Perform a gap check.

    1. Check the gap between the roof panel and roof glass.

      NOTICE:
      The gap must be even all around.

  1. B129372
    Using a T25 "TORX" driver, install the sliding roof glass with the 4 screws.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }


5. INSTALL SLIDING ROOF SIDE GARNISH LH

B129367
  1. Attach the claws to install the garnish.


6. INSTALL SLIDING ROOF SIDE GARNISH RH

HINT:
Use the same procedures described for the LH side.


7. INSPECT FOR WATER LEAKS
  1. Adjust the sliding roof glass sub-assembly, and inspect for water leaks.

  1. If there are any leaks, readjust the sliding roof glass sub-assembly.


8. INSTALL ROOF HEADLINING ASSEMBLY (for Short Body)
  1. Install the roof headlining (Click here).


9. INSTALL ROOF HEADLINING ASSEMBLY (for Long Body)
  1. Install the roof headlining (Click here).


10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
← INSTALLATION (Jan 2007 – Jul 2007)REMOVAL (from Nov 2005) →