2005-2008 RAV4 · Service Manual BRAKE

C1246/46 Master Cylinder Pressure Sensor Malfunction

Diagnostic trouble codes · Vehicles built Aug 2007 – Jul 2008

Also covers:

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 Aug 2007 – Jul 2008

DESCRIPTION

The master cylinder pressure sensor is connected to the skid control ECU in the ABS and TRACTION actuator.
DTC C1281/81 can be detected when the master cylinder pressure sensor sends a master cylinder pressure signal or test mode ends. DTC C1281/81 is output only in test mode.
DTC No.
DTC Detection Condition
Trouble Area
C1246/46
When one of following conditions is met:
  1. At vehicle speed of 7 km/h (4.3 mph) or more, when PMC terminal voltage over 0.86 V, voltage does not change by 0.005 V or more for 30 seconds.
  2. Noise occurs in the PMC terminal 7 times or more within 5 seconds.
  3. When stop light switch OFF, PMC terminal voltage more than 0.86 V or less than 0.3 V for 5 seconds or more.
  4. With IG1 terminal voltage between 9.5 V and 18.5 V, VCM terminal voltage not between 4.4 V and 5.6 V for 1.2 seconds or more.
  5. When VCM terminal voltage between 4.8 V and 5.2 V, PCM terminal voltage not between 0.19 V and 4.57 V for 1.2 seconds or more.
  1. Master cylinder pressure sensor
  2. Master cylinder pressure sensor circuit
  3. Stop light switch circuit
  4. ABS and TRACTION actuator
C1281/81
Detected only during test mode.
  1. Master cylinder pressure sensor
  2. Master cylinder pressure sensor circuit
  3. Stop light switch circuit
  4. ABS and TRACTION actuator

INSPECTION PROCEDURE

NOTICE:
When replacing the ABS and TRACTION actuator, perform zero point calibration (Click here).


1. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
  1. Check the Data List for proper functioning of the stop light switch.

    Skid control ECU 
    Item (Display)
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    Stop Lamp SW
    Stop light switch / ON or OFF
    ON: Brake pedal applied
    OFF: Brake pedal released
    -

    OK:
    ON (brake pedal is depressed) appears on the screen.



NG
CHECK STOP LIGHT SWITCH CIRCUIT
OK


2. READ VALUE USING INTELLIGENT TESTER (MASTER CYLINDER PRESSURE SENSOR)
  1. Check the Data List for proper functioning of the master cylinder pressure sensor.

    Skid control ECU 
    Item (Display)
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    Master Cylinder Sensor
    Master cylinder pressure sensor 1 reading / min.: 0 V, max.: 5 V
    When brake pedal released: 0.3 to 0.9 V
    -

    OK:
    When the pedal is depressed, the sensor output voltage increases.



NG
REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY
OK


3. RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Drive the vehicle at a speed of 30 km/h (18 mph) or more and perform a braking test (decelerate the vehicle by depressing the brake pedal).

  1. Check if the same DTC(s) is recorded (Click here).

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY


← C1246/46 Master Cylinder Pressure Sensor Malfunction (+ C1281/81) (Jan 2007 – Jul 2007)C1249/49 Open in Stop Light Switch Circuit (Nov 2005 – Dec 2006) →