Back-up Light Circuit
Circuit diagnosis · Vehicles built from Nov 2005
DESCRIPTION
A/T models: The park/neutral position switch turns on when the shift lever is moved into the R position, causing the back-up light to illuminate.M/T models: The back-up light switch turns on when the shift lever is moved into the R position, causing the back-up light to illuminate.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. INSPECT FUSE (GAUGE1) |
Remove the GAUGE1 fuse from the instrument panel junction block.
Measure the resistance of the fuse.
- Standard resistance:
- Below 1 Ω
|
|
||||
| OK | |
| 2. INSPECT BULB (BACK-UP LIGHT BULB) |
![]() ![]() |
Remove the rear combination light assembly.
Connect the positive (+) lead from the battery to terminal 6 and the negative (-) lead to terminal 1, then check that the bulb illuminates.
- OK:
- Bulb illuminates.
|
|
||||
| OK | |
| 3. CHECK TRANSAXLE TYPE |
- Result:
Transaxle Type
Proceed to
A/T
A
M/T
B
|
|
||||
| A | |
| 4. INSPECT PARK / NEUTRAL POSITION SWITCH |
![]() ![]() |
Disconnect the B28 park / neutral position switch connector.
Measure the resistance of the switch.
- Standard resistance:
Tester Condition
Shift Position
Specified Condition
2 (RB) - 1 (RL)
R
Below 1 Ω
2 (RB) - 1 (RL)
Except R
10 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK WIRE HARNESS (PARK/NEUTRAL POSITION SWITCH - BATTERY) |
![]() ![]() |
Disconnect the B28 park / neutral position switch connector.
Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Condition
Condition
Specified Condition
B28-2 (RB) - Body ground
Ignition switch on (IG)
10 to 14 V
|
|
||||
| OK | |
| 6. CHECK WIRE HARNESS (SWITCH - REAR COMBINATION LIGHT) |
![]() ![]() |
Disconnect the B28 park/neutral position switch connector.
Disconnect the K13 or K15 rear combination light connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Condition
Specified Condition
B28-1 - K13-1
Below 1 Ω
B28-1 - K15-1
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 7. INSPECT BACK-UP LIGHT SWITCH |
![]() ![]() |
Disconnect the B25 back-up light switch connector.
Measure the resistance of the switch.
- Standard resistance:
Tester Condition
Shift Position
Specified Condition
2 - 1
R (Pushed)
Below 1 Ω
2 - 1
Except R (Not pushed)
10 kΩ or higher
|
|
||||
| OK | |
| 8. CHECK WIRE HARNESS (BACK-UP LIGHT SWITCH - BATTERY) |
![]() ![]() |
Disconnect the B25 back-up light switch connector.
Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Condition
Condition
Specified Condition
B25-2 - Body ground
Ignition switch on (IG)
10 to 14 V
|
|
||||
| OK | |
| 9. CHECK WIRE HARNESS (BACK-UP LIGHT SWITCH - REAR COMBINATION LIGHT) |
![]() ![]() |
Disconnect the B25 back-up light switch connector.
Disconnect the K13 and K15 rear combination light connectors.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Condition
Specified Condition
B25-1 - K13-1
Below 1 Ω
B25-1 - K15-1
Below 1 Ω
|
|
||||
| OK | ||
| ||







