2005-2008 RAV4 · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Nov 2005


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


2. REMOVE RADIATOR SUPPORT OPENING COVER

3. REMOVE FRONT WHEEL RH

4. REMOVE NO. 1 ENGINE UNDER COVER

5. REMOVE FRONT FENDER APRON RH

6. REMOVE NO. 1 ENGINE COVER

  1. A112206
    Remove the 2 nuts and cover.


7. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug and drain the oil into a container.


8. REMOVE FRONT EXHAUST PIPE
  1. Remove the 2 bolts, 2 compression springs and front exhaust pipe.

  1. Remove the gasket from the exhaust manifold.

    A126831


9. REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT RH
  1. Remove the 4 bolts and reinforcement RH.


10. REMOVE FAN AND GENERATOR V BELT

  1. A114351E01
    Using SST and 19 mm socket wrench, loosen the V-ribbed belt tensioner arm clockwise, then remove the fan and generator V belt.
    SST
    09216-42010  

    NOTICE:
    1. Be sure to connect SST and the tools so that they are in line during use.
    2. When retracting the tensioner, turn it clockwise slowly for 3 seconds or more. Do not apply force rapidly.
    3. After the tensioner is fully retracted, do not apply force any more than necessary.


11. REMOVE GENERATOR ASSEMBLY

A122809
  1. Disconnect the generator connector.

  1. Remove the terminal cap.

  1. Remove the nut and disconnect the generator wire.

  1. Remove the bolt and wire harness clamp bracket.

  1. Remove the wire harness clamps.

  1. A122810
    Remove the 2 bolts and generator.


12. REMOVE RADIATOR RESERVOIR

  1. A124838
    Remove the 2 bolts and radiator reservoir with the No. 1 and No. 2 water by-pass hose.


13. REMOVE ENGINE MOUNTING INSULATOR RH

  1. A098189E02
    Remove the bolt of the wire harness protector.

  1. Disconnect the 2 clamps of the engine wire.

  1. A061184E04
    Place a transmission jack underneath the engine, then put a wooden block on the jack.

  1. A124843
    Remove the 4 bolts, 2 nuts and engine mounting insulator RH.

    NOTICE:
    Do not apply excessive force to the return tube when removing the engine mounting insulator RH.

    HINT:
    Keep clearance by lowering the engine using the transmission jack when removing the engine mounting insulator FR.


14. REMOVE ENGINE MOUNTING INSULATOR FR

  1. A124839
    Remove the through bolt and nut.

  1. A124840
    Remove the 2 bolts and engine mounting insulator FR.

    HINT:
    Keep clearance by lowering the engine using the transmission jack when removing the engine mounting insulator FR.


15. REMOVE IDLER PULLEY

  1. A132481
    Loosen the 2 bolts and remove the idler bracket with the 2 bolts.


16. REMOVE IGNITION COIL ASSEMBLY
  1. Disconnect the 4 ignition coil connectors.

  1. A124400
    Remove the 4 bolts and 4 ignition coils.


17. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A112209
    Disconnect the 2 ventilation hoses from the cylinder head cover.

  1. A112210E01
    Remove the 2 bolts and disconnect the 2 engine wires.

  1. A112211
    Remove the 8 bolts, 2 nuts and cylinder head cover.


18. REMOVE OIL PAN SUB-ASSEMBLY

  1. A112213E01
    Install the No. 1 and No. 2 engine hangers with the bolts.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }

    Part No. 
    Item
    Part No.
    No. 1 engine hanger
    12281-28010
    No. 2 engine hanger
    12282-28010
    Bolt
    91512-61020

  1. Attach the sling device to the engine hangers and chain block.

  1. A114333
    Remove the 12 bolts and 2 nuts.

  1. A000019E05
    Insert the blade of SST between the crankcase, chain cover and oil pan, then cut off the applied sealer and remove the oil pan.
    SST
    09032-00100  

    NOTICE:
    Be careful not to damage the contact surface of the crankcase, chain cover and oil pan.


19. SET NO. 1 CYLINDER TO TDC/COMPRESSION

  1. A098345E09
    Turn the crankshaft pulley until its groove and the timing mark "0" of the timing chain cover are aligned.

  1. Check that each timing mark of the camshaft timing gear and sprocket is aligned with each timing mark located on the No. 1 and No. 2 bearing caps as shown in the illustration.
    If not, turn the crankshaft by 1 revolution (360°) to align the timing marks as above.


20. REMOVE CRANKSHAFT PULLEY

  1. A013697E02
    Using SST, fix the pulley in place and loosen the pulley bolt.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A124860E01
    Remove the crankshaft pulley.

    HINT:
    If necessary, remove the pulley with SST and the pulley bolt.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)
    09950-40011   (09957-04010)


21. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

  1. A098348E01
    Remove the 2 nuts, chain tensioner and gasket.

    NOTICE:
    Do not turn the crankshaft without the chain tensioner.


22. REMOVE ENGINE MOUNTING BRACKET RH

  1. A128165
    Remove the 3 bolts and engine mounting bracket RH.


23. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
  1. Lift the engine upward using the transmission jack.

    NOTICE:
    Do not lift the engine more than necessary.

  1. A112212
    Remove the bolt, nut and V-ribbed belt tensioner.


24. REMOVE CRANKSHAFT POSITION SENSOR

A097797E01
  1. Disconnect the sensor connector.

  1. Remove the connector clamp.

  1. Remove the wire harness from the wire harness clamp bracket.

  1. Remove the wire harness clamp.

  1. Remove the bolt and sensor.


25. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

  1. A014253E03
    Using an E10 "torx" socket, remove the stud bolt for the V-ribbed belt tensioner.

  1. A132568E01
    Remove the 12 bolts and 2 nuts.

  1. A128179
    Remove the timing chain cover by prying the portions between the timing chain cover, cylinder head and cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing chain cover, cylinder head and cylinder block.


26. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

A132571

27. REMOVE TIMING CHAIN GUIDE

  1. A077243E01
    Remove the bolt and timing chain guide.


28. REMOVE CHAIN TENSIONER SLIPPER

  1. A128183
    Remove the bolt and chain tensioner slipper.


29. REMOVE NO. 1 CHAIN VIBRATION DAMPER

  1. A128184
    Remove the 2 bolts and chain vibration damper.


30. REMOVE CHAIN SUB-ASSEMBLY

A128185

31. REMOVE CRANKSHAFT TIMING SPROCKET

A128186

32. REMOVE NO. 2 CHAIN SUB-ASSEMBLY

  1. A098351E01
    Turn the crankshaft by 90°counterclockwise to align the adjusting hole of the oil pump drive shaft sprocket with the groove of the oil pump.

  1. A098352E01
    Insert a 4 mm diameter bar into the adjusting hole of the oil pump drive shaft sprocket to lock the gear in position, and then remove the nut.

  1. B011415E03
    Remove the bolt, chain tensioner plate and spring.

  1. Remove the oil pump drive sprocket, oil pump drive shaft sprocket and No. 2 chain.

← COMPONENTS (from Nov 2005)INSPECTION (from Nov 2005) →