2005-2008 RAV4 · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built from Nov 2005

HINT:
  1. Thoroughly clean all parts to be assembled.
  2. Before installing the parts, apply fresh engine oil to all sliding and rotating surfaces.
  3. Replace oil seals with new ones.


1. INSTALL VALVE STEM OIL SEAL

  1. A124784E01
    A124785E01
    Using SST, push in a new oil seal.
    SST
    09201-41020  

    HINT:
    The intake valve oil seal is gray and the exhaust valve oil seal is black.

    NOTICE:
    Pay close attention when installing the intake and exhaust oil seals. For example, installing the intake oil seal into the exhaust or installing the exhaust oil seal to the intake can cause installation problems later.


2. INSTALL INTAKE VALVE
  1. Place the cylinder head on wooden blocks.

  1. A126924E01
    Install the valve, seat, spring and retainer onto the cylinder head.

  1. A098132E01
    Using SST, compress the spring, and place the 2 retainer locks around the valve stem.
    SST
    09202-70020   (09202-00010)

  1. A112168E04
    Using a plastic-faced hammer and discarded valve (with its tip wrapped with tape), lightly tap the installed valve to fit it into place.

    NOTICE:
    Be careful not to damage the valve stem tip.


3. INSTALL EXHAUST VALVE
  1. Place the cylinder head on wooden blocks.

  1. A126925E01
    Install the valve, seat, spring and retainer onto the cylinder head.

  1. A098133E01
    Using SST, compress the spring, and place the 2 retainer locks around the valve stem.
    SST
    09202-70020   (09202-00010)

  1. A098144E07
    Using a plastic-faced hammer and discarded valve (with its tip wrapped with tape), lightly tap the installed valve to fit it into place.

    NOTICE:
    Be careful not to damage the valve stem tip.


4. INSTALL VALVE LIFTER
  1. Assemble the valve lifter and the tip of the valve stem with a light coat of engine oil applied.

    NOTICE:
    Install the valve lifters in their original places.


5. INSTALL NO. 1 CAMSHAFT BEARING
  1. Clean the contact surfaces of the bearing and the bearing cap.

    NOTICE:
    Do not apply engine oil to the contact surfaces of the camshaft bearing and bearing cap.

  1. A124773
    Align the bearing claw with the claw groove of No. 1 and No. 2 bearing cap, and push in the No. 1 camshaft bearing.


6. INSTALL NO. 2 CAMSHAFT BEARING
  1. Clean the contact surfaces of the bearing and the cylinder head.

    NOTICE:
    Do not apply engine oil to the contact surfaces of the camshaft bearing and cylinder block.

  1. A013383E01
    Install the No. 2 camshaft bearing onto the cylinder head.


7. INSTALL CAMSHAFT POSITION SENSOR

  1. A114368
    Install the sensor with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


8. INSTALL ENGINE COOLANT TEMPERATURE SENSOR

  1. A114367E01
    Install a new gasket and the ECT sensor.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


9. INSTALL ENGINE OIL PRESSURE SWITCH
  1. Apply adhesive to 2 or 3 threads of the oil pressure switch.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or Equivalent

  1. A114362
    Install the oil pressure switch.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


10. INSTALL RADIO SETTING CONDENSER

  1. A112227
    Install the condenser with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

← REPLACEMENT (from Nov 2005)INSTALLATION (from Nov 2005) →