2005-2008 RAV4 · Service Manual COMMUNICATION SYSTEM

TERMINALS OF ECU

System information · Vehicles built from Aug 2008

Versions by build date: Nov 2005 – Jul 2008 from Aug 2008

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the main wire and the branch wire.
  2. For Auto:
    After the ignition switch is turned off, check that the key reminder warning system is not in operation.
  3. For Reminder:
    After the ignition switch is turned off, check that the key reminder warning system and light reminder buzzer are not in operation.
  4. Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


JUNCTION CONNECTOR (LHD)

  1. No. 1 Junction Connector
    C132298E04

    No. 1 Junction Connector
    Wiring Color
    Connect to
    CANH (A51-1)
    R
    Brake actuator (skid control ECU)*1
    ABS and traction actuator (skid control ECU)*2
    CANL (A51-12)
    W
    Brake actuator (skid control ECU)*1
    ABS and traction actuator (skid control ECU)*2
    CANH (A51-2)
    Y
    ECM
    CANL (A51-13)
    W
    ECM
    CANH (A51-3)
    L
    No. 2 junction connector
    CANL (A51-14)
    W
    No. 2 junction connector

    HINT:
    *1: w/ Anti-lock Brake System
    *2: w/ Vehicle Stability Control System

  2. No. 2 Junction Connector
    C132299E06

    No. 2 Junction Connector
    Wiring Color
    Connect to
    CANH (E75-3)
    L
    No. 1 junction connector
    CANL (E75-14)
    W
    No. 1 junction connector
    CANH (E75-5)
    L
    Yaw rate sensor*1
    CANL (E75-16)
    W
    Yaw rate sensor*1
    CANH (E75-6)
    Y
    Power steering ECU
    CANL (E75-17)
    W
    Power steering ECU
    CANH (E75-8)
    R
    Main body ECU
    CANL (E75-19)
    W
    Main body ECU
    CANH (E75-7)
    BR
    Steering angle sensor*2
    CANL (E75-18)
    W
    Steering angle sensor*2
    CANH (E75-2)
    B
    DLC3
    CANL (E75-13)
    W
    DLC3
    CANH (E75-4)
    V
    Air conditioning amplifier
    CANL (E75-15)
    W
    Air conditioning amplifier
    CANH (E75-1)
    SB
    No. 3 junction connector
    CANL (E75-12)
    W
    No. 3 junction connector

    HINT:
    *1: w/ Vehicle Stability Control System
    *2: for 2WD (w/ Vehicle Stability Control System) and 4WD

  3. No. 3 Junction Connector
    C132298E05

    No. 3 Junction Connector
    Wiring Color
    Connect to
    CANH (E77-3)
    SB
    No. 2 junction connector
    CANL (E77-14)
    W
    No. 2 junction connector
    CANH (E77-1)
    B
    Center airbag sensor assembly
    CANL (E77-12)
    W
    Center airbag sensor assembly
    CANH (E77-2)
    V
    No. 4 junction connector
    CANL (E77-13)
    W
    No. 4 junction connector

  4. No. 4 Junction Connector
    C132299E07

    No. 4 Junction Connector
    Wiring Color
    Connect to
    CANH (E76-4)
    V
    No. 3 junction connector
    CANL (E76-15)
    W
    No. 3 junction connector
    CANH (E76-7)
    P
    4WD control ECU*1
    CANL (E76-18)
    W
    4WD control ECU*1
    CANH (E76-5)
    G
    Combination meter ECU
    CANL (E76-16)
    W
    Combination meter ECU
    CANP (E76-11)
    O
    Main body ECU*2
    CANN (E76-22)
    W
    Main body ECU*2
    CANH (E76-10)
    SB
    Certification ECU*2
    CANL (E76-21)
    W
    Certification ECU*2
    MSCH (E76-9)
    LG
    Combination meter ECU*2
    MSCL (E76-20)
    W
    Combination meter ECU*2

    HINT:
    *1: for 4WD
    *2: w/ Entry and Start System


JUNCTION CONNECTOR (RHD)

  1. No. 1 Junction Connector
    C132298E04

    No. 1 Junction Connector
    Wiring Color
    Connect to
    CANH (A51-1)
    R
    Brake actuator (skid control ECU)*1
    ABS and traction actuator (skid control ECU)*2
    CANL (A51-12)
    W
    Brake actuator (skid control ECU)*1
    ABS and traction actuator (skid control ECU)*2
    CANH (A51-2)
    Y
    ECM
    CANL (A51-13)
    W
    ECM
    CANH (A51-3)
    L
    No. 2 junction connector
    CANL (A51-14)
    W
    No. 2 junction connector

    HINT:
    *1: w/ Anti-lock Brake System
    *2: w/ Vehicle Stability Control System

  2. No. 2 Junction Connector
    C132298E09

    No. 2 Junction Connector
    Wiring Color
    Connect to
    CANH (E87-4)
    L
    No. 1 junction connector
    CANL (E87-15)
    W
    No. 1 junction connector
    CANH (E87-2)
    L
    Yaw rate sensor*
    CANL (E87-13)
    W
    Yaw rate sensor*
    CANH (E87-5)
    R
    Main body ECU
    CANL (E87-16)
    W
    Main body ECU
    CANH (E87-1)
    SB
    No. 3 junction connector
    CANL (E87-12)
    W
    No. 3 junction connector

    HINT:
    *: w/ Vehicle Stability Control System

  3. No. 3 Junction Connector
    C132298E07

    No. 3 Junction Connector
    Wiring Color
    Connect to
    CANH (E77-3)
    SB
    No. 2 junction connector
    CANL (E77-14)
    W
    No. 2 junction connector
    CANH (E77-4)
    Y
    Power steering ECU
    CANL (E77-15)
    W
    Power steering ECU
    CANH (E77-2)
    V
    Air conditioning amplifier
    CANL (E77-13)
    W
    Air conditioning amplifier
    CANH (E77-1)
    B
    Center airbag sensor assembly
    CANL (E77-12)
    W
    Center airbag sensor assembly
    CANH (E77-5)
    V
    No. 4 junction connector
    CANL (E77-16)
    W
    No. 4 junction connector

  4. No. 4 Junction Connector
    C197678E01
    C132298E47

    No. 4 Junction Connector
    Wiring Color
    Connect to
    CANH (E89-6)
    V
    No. 3 junction connector
    CANL (E89-17)
    W
    No. 3 junction connector
    CANH (E88-6)
    P
    4WD control ECU*1
    CANL (E88-17)
    W
    4WD control ECU*1
    CANH (E88-7)
    BR
    Steering angle sensor*3
    CANL (E88-18)
    W
    Steering angle sensor*3
    CANH (E89-5)
    B
    DLC3
    CANL (E89-16)
    W
    DLC3
    CANH (E88-5)
    G
    Combination meter ECU
    CANL (E88-16)
    W
    Combination meter ECU
    CANP (E89-11)
    O
    Main body ECU*2
    CANN (E89-22)
    W
    Main body ECU*2
    CANH (E88-2)
    SB
    Certification ECU*2
    CANL (E88-13)
    W
    Certification ECU*2
    MSCH (E88-1)
    LG
    Combination meter ECU*2
    MSCL (E88-12)
    W
    Combination meter ECU*2

    HINT:
    *1: for 4WD
    *2: w/ Entry and Start System
    *3: for 2WD (w/ Vehicle Stability Control System) and 4WD


CHECK DLC3

  1. H100769E33
    Measure the resistance according to the value(s) in the table below.
    Symbols (Terminal No.)
    Wiring Color
    Condition
    Specified Condition
    CANH (E16-6) - CANL (E16-14)
    B - W
    Ignition switch off
    54 to 69 Ω
    CANH (E16-6) - CG (E16-4)
    B - BR
    Ignition switch off
    200 Ω or more
    CANL (E16-14) - CG (E16-4)
    W - BR
    Ignition switch off
    200 Ω or more
    CANH (E16-6) - BAT (E16-16)
    B - L
    Ignition switch off
    1 MΩ or more
    CANL (E16-14) - BAT (E16-16)
    W - L
    Ignition switch off
    1 MΩ or more


CHECK BRAKE ACTUATOR (SKID CONTROL ECU)

HINT:
For vehicle with Anti-lock Brake System only.

C128344E01
  1. Disconnect the A27 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Condition
    Specified Condition
    CANH (A27-6) - CANL (A27-5)
    R - W
    Ignition switch off
    54 to 69 Ω
    CANH (A27-6) - GND1 (A27-2)
    R - W-B
    Ignition switch off
    200 Ω or more
    CANL (A27-5) - GND1 (A27-2)
    W - W-B
    Ignition switch off
    200 Ω or more
    CANH (A27-6) - +BS (A27-1)
    R - W
    Ignition switch off
    1 MΩ or more
    CANL (A27-5) - +BS (A27-1)
    W - W
    Ignition switch off
    1 MΩ or more


CHECK ABS AND TRACTION ACTUATOR (SKID CONTROL ECU)

HINT:
For vehicle with Vehicle Stability Control System only.

C190577E04
  1. Disconnect the A67 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Condition
    Specified Condition
    CANH (A67-25) - CANL (A67-14)
    R - W
    Ignition switch off
    54 to 69 Ω
    CANH (A67-25) - GND1 (A67-1)
    R - W-B
    Ignition switch off
    200 Ω or more
    CANL (A67- 14) - GND1 (A67-1)
    W - W-B
    Ignition switch off
    200 Ω or more
    CANH (A67-25) - +BS (A67-12)
    R - W
    Ignition switch off
    1 MΩ or more
    CANL (A67-14) - +BS (A67-12)
    W - W
    Ignition switch off
    1 MΩ or more


CHECK STEERING ANGLE SENSOR

HINT:
For 2WD with Vehicle Stability Control System and 4WD only.

C193294E02
  1. Disconnect the E95 sensor connector.

  2. Measure the resistance according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Condition
    Specified Condition
    CANH (E95-3) - CANL (E95-2)
    BR - W
    Ignition switch off
    54 to 69 Ω
    CANH (E95-3) - ESS (E95-1)
    BR - W-B
    Ignition switch off
    200 Ω or more
    CANL (E95-2) - ESS (E95-1)
    W - W-B
    Ignition switch off
    200 Ω or more
    CANH (E95-3) - BAT (E95-5)
    BR - R
    Ignition switch off
    1 MΩ or more
    CANL (E95-2) - BAT (E95-5)
    W - R
    Ignition switch off
    1 MΩ or more


CHECK YAW RATE SENSOR

HINT:
For vehicle with Vehicle Stability Control System only.

C190673E05
  1. Disconnect the K25 sensor connector.

  2. Measure the resistance according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Condition
    Specified Condition
    CANH (K25-3) - CANL (K25-2)
    L - W
    Ignition switch off
    54 to 69 Ω
    CANH (K25-3) - GND (K25-1)
    L - W-B
    Ignition switch off
    200 Ω or more
    CANL (K25-2) - GND (K25-1)
    W - W-B
    Ignition switch off
    200 Ω or more
    CANH (K25-3) - BAT (E16-16)
    L - L
    Ignition switch off
    1 MΩ or more
    CANL (K25-2) - BAT (E16-16)
    W - L
    Ignition switch off
    1 MΩ or more


CHECK AIR CONDITIONING AMPLIFIER (for AUTOMATIC AIR CONDITIONING SYSTEM)
C128168E01
  1. Disconnect the E41 amplifier connector.

  2. Measure the resistance according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Condition
    Specified Condition
    CANH (E41-11) - CANL (E41-12)
    V - W
    Ignition switch off
    54 to 69 Ω
    CANH (E41-11) - GND (E41-14)
    V - W-B
    Ignition switch off
    200 Ω or more
    CANL (E41-12) - GND (E41-14)
    W - W-B
    Ignition switch off
    200 Ω or more
    CANH (E41-11) - B (E41-21)
    V - R
    Ignition switch off
    1 MΩ or more
    CANL (E41-12) - B (E41-21)
    W - R
    Ignition switch off
    1 MΩ or more


CHECK AIR CONDITIONING AMPLIFIER (for MANUAL AIR CONDITIONING SYSTEM)
C133298E02
  1. Disconnect the E42 amplifier connector.

  2. Measure the resistance according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Condition
    Specified Condition
    CANH (E42-8) - CANL (E42-9)
    V - W
    Ignition switch off
    54 to 69 Ω
    CANH (E42-8) - GND (E42-24)
    V - W-B
    Ignition switch off
    200 Ω or more
    CANL (E42-9) - GND (E42-24)
    W - W-B
    Ignition switch off
    200 Ω or more
    CANH (E42-8) - BAT (E16-16)
    V - L
    Ignition switch off
    1 MΩ or more
    CANL (E42-9) - BAT (E16-16)
    W - L
    Ignition switch off
    1 MΩ or more


CHECK ECM
C128047E20
  1. Disconnect the A12 and B96*1 or B32*2,*3 ECM connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Condition
    Specified Condition
    CANH (A12-41) - CANL (A12-49)*1, *2
    Y - W
    Ignition switch off
    108 to 132 Ω
    CANH (A12-41) - E1 (B32-81)*1
    Y - BR
    Ignition switch off
    200 Ω or more
    CANL (A12-49) - E1 (B96-81)*1
    W - BR
    Ignition switch off
    200 Ω or more
    CANH (A12-41) - E1 (B96-104)*2
    Y - BR
    Ignition switch off
    200 Ω or more
    CANL (A12-49) - E1 (B32-104)*2
    W - BR
    Ignition switch off
    200 Ω or more
    CANH (A12-41) - BATT (A12-20)*1, *2
    Y - W
    Ignition switch off
    1 MΩ or more
    CANL (A12-49) - BATT (A12-20)*1, *2
    W - W
    Ignition switch off
    1 MΩ or more
    CANH (A12-38) - CANL (A12-46)*3
    Y - W
    Ignition switch off
    108 to 132 Ω
    CANH (A12-38) - E1 (B32-109)*3
    Y - BR
    Ignition switch off
    200 Ω or more
    CANL (A12-46) - E1 (B32-109)*3
    W - BR
    Ignition switch off
    200 Ω or more
    CANH (A12-38) - BATT (A12-2)*3
    Y - W
    Ignition switch off
    1 MΩ or more
    CANL (A12-46) - BATT (A12-2)*3
    W - W
    Ignition switch off
    1 MΩ or more

    HINT:
    *1: for Gasoline engine (2GR-FE)
    *2: for Gasoline engine (1AZ-FE, 2AZ-FE)
    *3: for Diesel engine


CHECK CENTER AIRBAG SENSOR ASSEMBLY
C128046E06
  1. Disconnect the E49 sensor connector.

  2. Measure the resistance according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Condition
    Specified Condition
    CANH (E49-13) - CANL (E49-22)
    B - W
    Ignition switch off
    54 to 69 Ω
    CANH (E49-13) - E1 (E49-25)
    B - W-B
    Ignition switch off
    200 Ω or more
    CANL (E49-22) - E1 (E49-25)
    W - W-B
    Ignition switch off
    200 Ω or more
    CANH (E49-13) - BAT (E16-16)
    B - L
    Ignition switch off
    1 MΩ or more
    CANL (E49-22) - BAT (E16-16)
    W - L
    Ignition switch off
    1 MΩ or more


CHECK POWER STEERING ECU
C128167E01
  1. Disconnect the A2 and E21 ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Condition
    Specified Condition
    CANH (E21-2) - CANL (E21-8)
    Y - W
    Ignition switch off
    54 to 69 Ω
    CANH (E21-2) - PGND (A2-2)
    Y - W-B
    Ignition switch off
    200 Ω or more
    CANL (E21-8) - PGND (A2-2)
    W - W-B
    Ignition switch off
    200 Ω or more
    CANH (E21-2) - PIG (A2-1)
    Y - W-B*1
    Y - L*2
    Ignition switch off
    1 MΩ or more
    CANL (E21-8) - PIG (A2-1)
    W - W-B*1
    W - L*2
    Ignition switch off
    1 MΩ or more

    HINT:
    *1: for LHD
    *2: for RHD


CHECK COMBINATION METER ECU
C128516E03
  1. Disconnect the E22 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Condition
    Specified Condition
    CANH (E22-32) - CANL (E22-31)
    G - W
    Ignition switch off
    108 to 132 Ω
    CANH (E22-32) - ET (E22-33)
    G - BR
    Ignition switch off
    200 Ω or more
    CANL (E22-31) - ET (E22-33)
    W - BR
    Ignition switch off
    200 Ω or more
    CANH (E22-32) - B (E22-22)
    G - R
    Ignition switch off
    1 MΩ or more
    CANL (E22-31) - B (E22-22)
    W - R
    Ignition switch off
    1 MΩ or more
    MSCH (E22-9) - MSCL (E22-10)*
    LG - W
    Ignition switch off
    108 to 132 Ω
    MSCH (E22-9) - ET (E22-33)*
    LG - BR
    Ignition switch off
    200 Ω or more
    MSCL (E22-10) - ET (E22-33)*
    W - BR
    Ignition switch off
    200 Ω or more
    MSCH (E22-9) - B (E22-22)*
    LG - R
    Ignition switch off
    1 MΩ or more
    MSCL (E22-10) - B (E22-22)*
    W - R
    Ignition switch off
    1 MΩ or more

    HINT:
    *: w/ Entry and Start System


CHECK CERTIFICATION ECU

HINT:
For vehicle with entry and start system only.

B108931E45
  1. Disconnect the E63 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Condition
    Specified Condition
    CANH (E63-27) - CANL (E63-28)
    SB - W
    Ignition switch off
    54 to 69 Ω
    CANH (E63-27) - E (E63-17)
    SB- W-B
    Ignition switch off
    200 Ω or more
    CANL (E63-28) - E (E63-17)
    W - W-B
    Ignition switch off
    200 Ω or more
    CANH (E63-27) - +B1 (E63-1)
    SB - R
    Ignition switch off
    1 MΩ or more
    CANL (E63-28) - +B1 (E63-1)
    W - R
    Ignition switch off
    1 MΩ or more


CHECK INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)
C129203E07
C129202E10
  1. Disconnect the IB and IE junction block connectors.

  2. Disconnect the E19 and E20 ECU connectors.

  3. Measure the resistance according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Condition
    Specified Condition
    CANH (E20-15) - CANL (E20-16)
    R - W
    Ignition switch off
    54 to 69 Ω
    CANH (E20-15) - GND1 (IE-17)
    R - W-B
    Ignition switch off
    200 Ω or more
    CANL (E20-16) - GND1 (IE-17)
    W - W-B
    Ignition switch off
    200 Ω or more
    CANH (E20-15) - BECU (IB-30)
    R - R
    Ignition switch off
    1 MΩ or more
    CANL (E20-16) - BECU (IB-30)
    W - R
    Ignition switch off
    1 MΩ or more
    CANP (E19-11) - CANN (E19-12)*
    O - W
    Ignition switch off
    108 to 132 Ω
    CANP (E19-11) - GND1 (IE-17)*
    O - W-B
    Ignition switch off
    200 Ω or more
    CANN (E19-12) - GND1 (IE-17)*
    W - W-B
    Ignition switch off
    200 Ω or more
    CANP (E19-11) - BECU (IB-30)*
    O - R
    Ignition switch off
    1 MΩ or more
    CANN (E19-12) - BECU (IB-30)*
    W - R
    Ignition switch off
    1 MΩ or more

    HINT:
    *: w/ Entry and Start System


CHECK 4WD CONTROL ECU (for 4WD)
C128343E01
  1. Disconnect the E67 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Condition
    Specified Condition
    CANH (E67-14) - CANL (E67-16)
    P - W
    Ignition switch off
    54 to 69 Ω
    CANH (E67-14) - GND (E67-23)
    P - W-B
    Ignition switch off
    200 Ω or more
    CANL (E67-16) - GND (E67-23)
    W - W-B
    Ignition switch off
    200 Ω or more
    CANH (E67-14) - BSLC (E67-9)
    P - R
    Ignition switch off
    1 MΩ or more
    CANL (E67-16) - BSLC (E67-9)
    W -R
    Ignition switch off
    1 MΩ or more

← TERMINALS OF ECU (Nov 2005 – Jul 2008)DIAGNOSIS SYSTEM (Nov 2005 – Jul 2008) →