2005-2008 RAV4 · Service Manual COMMUNICATION SYSTEM

Check CAN Bus Lines for Short Circuit (LHD Models)

Circuit diagnosis · Vehicles built Nov 2005 – Jul 2008

Versions by build date: Nov 2005 – Jul 2008 from Aug 2008

DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω.
  1. Short between CAN bus lines
  2. Brake actuator (skid control ECU)*1
  3. ABS and traction actuator (skid control ECU)*2
  4. Power steering ECU
  5. Steering angle sensor*4
  6. Yaw rate sensor*2
  7. ECM
  8. Center airbag sensor assembly
  9. Air conditioning amplifier
  10. Combination meter ECU
  11. Instrument panel junction block (Main body ECU)
  12. 4WD control ECU*3
  13. No. 1 junction connector
  14. No. 2 junction connector
  15. No. 3 junction connector
  16. No. 4 junction connector

HINT:
*1: w/ ABS
*2: w/ VSC
*3: for 4WD
*4: for 2WD with VSC and 4WD


WIRING DIAGRAM

C132302E03
C129463E11

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the main wire and the branch wire.
  2. For Auto:
    After the ignition switch is turned off, check that the key reminder warning system is not in operation.
  3. For Reminder:
    After the ignition switch is turned off, check that the key reminder warning system and light reminder buzzer are not in operation.
  4. Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. CHECK CAN BUS LINES FOR SHORT CIRCUIT (DLC3 BRANCH WIRE)

  1. H100769E34
    Disconnect the E75 No. 2 junction connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-14 (CANL)
    Ignition switch off
    1 MΩ or more



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


2. CONNECT CONNECTOR
  1. Reconnect the E75 No. 2 junction connector.


NEXT


3. CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 1 JUNCTION CONNECTOR SIDE)

  1. H100769E34
    Disconnect the A51 No. 1 junction connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-14 (CANL)
    Ignition switch off
    108 to 132 Ω



OK
Go to step 14
NG


4. CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

  1. C127797E06
    Disconnect the E75 No. 2 junction connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E75-3 (CANH) - E75-14 (CANL)
    Ignition switch off
    1 MΩ or more



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK


5. CONNECT CONNECTOR
  1. Reconnect the A51 No. 1 junction connector.

  1. Reconnect the E75 No. 2 junction connector.


NEXT


6. CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 3 JUNCTION CONNECTOR, NO. 4 JUNCTION CONNECTOR SIDE)

  1. H100769E34
    Disconnect the E77 No. 3 junction connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-14 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 23
OK


7. CONNECT CONNECTOR
  1. Reconnect the E77 No. 3 junction connector.


NEXT


8. CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 4 JUNCTION CONNECTOR SIDE)

  1. H100769E34
    Disconnect the E76 No. 4 junction connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-14 (CANL)
    Ignition switch off
    108 to 132 Ω



OK
Go to step 39
NG


9. CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)

  1. C127797E50
    Disconnect the E77 No. 3 junction connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E77-3 (CANH) - E77-14 (CANL)
    Ignition switch off
    1 MΩ or more



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
OK


10. CONNECT CONNECTOR
  1. Reconnect the E76 No. 4 junction connector.


NEXT


11. CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 3 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)

  1. C127797E51
    Measure the resistance of the wire harness side connector.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    E77-1 (CANH) - E77-12 (CANL)
    Ignition switch off
    Below 1 Ω
    A
    E77-1 (CANH) - E77-12 (CANL)
    Ignition switch off
    Other
    B



B
REPAIR OR REPLACE NO. 3 JUNCTION CONNECTOR
A


12. CONNECT CONNECTOR
  1. Reconnect the E77 No. 3 junction connector.


NEXT


13. CHECK CAN BUS LINES FOR SHORT CIRCUIT (CENTER AIRBAG SENSOR ASSEMBLY)

  1. H100769E34
    Disconnect the E49 center airbag sensor connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-14 (CANL)
    Ignition switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CANH, CANL)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

14. CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 1 JUNCTION CONNECTOR - BRAKE ACTUATOR)

NOTICE:
For vehicles without ABS, go to "CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 1 JUNCTION CONNECTOR - ABS AND TRACTION ACTUATOR)".

  1. C127797E53
    Measure the resistance of the wire harness side connector.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    A51-1 (CANH) - A51-12 (CANL)
    Ignition switch off
    Below 1 Ω
    A
    A51-1 (CANH) - A51-12 (CANL)
    Ignition switch off
    Other
    B



A
Go to step 17
B


15. CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 1 JUNCTION CONNECTOR - ABS AND TRACTION ACTUATOR)

NOTICE:
For vehicles without VSC, go to "CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 1 JUNCTION CONNECTOR - ECM)".

  1. C127797E54
    Measure the resistance of the wire harness side connector.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    A51-1 (CANH) - A51-12 (CANL)
    Ignition switch off
    Below 1 Ω
    A
    A51-1 (CANH) - A51-12 (CANL)
    Ignition switch off
    Other
    B



A
Go to step 19
B


16. CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 1 JUNCTION CONNECTOR - ECM)

  1. C127797E52
    Measure the resistance of the wire harness side connector.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    A51-2 (CANH) - A51-13 (CANL)
    Ignition switch off
    Below 1 Ω
    A
    A51-2 (CANH) - A51-13 (CANL)
    Ignition switch off
    Other
    B



A
Go to step 21
B

REPAIR OR REPLACE NO. 1 JUNCTION CONNECTOR

17. CONNECT CONNECTOR
  1. Reconnect the A51 No. 1 junction connector.


NEXT


18. CHECK CAN BUS LINES FOR SHORT CIRCUIT (BRAKE ACTUATOR)

  1. H100769E34
    Disconnect the A27 brake actuator (skid control ECU) connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-14 (CANL)
    Ignition switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BRAKE ACTUATOR (CANH, CANL)
OK

REPLACE BRAKE ACTUATOR (SKID CONTROL ECU)

19. CONNECT CONNECTOR
  1. Reconnect the A51 No. 1 junction connector.


NEXT


20. CHECK CAN BUS LINES FOR SHORT CIRCUIT (ABS AND TRACTION ACTUATOR)

  1. H100769E34
    Disconnect the A26 ABS and traction actuator (skid control ECU) connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-14 (CANL)
    Ignition switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO ABS AND TRACTION ACTUATOR (CANH, CANL)
OK

REPLACE ABS AND TRACTION ACTUATOR (SKID CONTROL ECU)

21. CONNECT CONNECTOR
  1. Reconnect the A51 No. 1 junction connector.


NEXT


22. CHECK CAN BUS LINES FOR SHORT CIRCUIT (ECM)

  1. H100769E34
    Disconnect the A12 ECM connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-14 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (NO. 1 JUNCTION CONNECTOR - ECM)
OK

REPLACE ECM

23. CONNECT CONNECTOR
  1. Reconnect the E77 No. 3 junction connector.


NEXT


24. CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 2 JUNCTION CONNECTOR - YAW RATE SENSOR)

NOTICE:
For vehicles without VSC, go to "CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 2 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)".

  1. C127797E55
    Disconnect the E75 No. 2 junction connector.Measure the resistance of the wire harness side connector.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    E75-5 (CANH) - E75-16 (CANL)
    Ignition switch off
    Below 1 Ω
    A
    E75-5 (CANH) - E75-16 (CANL)
    Ignition switch off
    Other
    B



A
Go to step 29
B


25. CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 2 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)

NOTICE:
For vehicles without 2WD with VSC and 4WD, go to "CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 2 JUNCTION CONNECTOR - POWER STEERING ECU)".

  1. C127797E59
    Measure the resistance of the wire harness side connector.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    E75-7 (CANH) - E75-18 (CANL)
    Ignition switch off
    Below 1 Ω
    A
    E75-7 (CANH) - E75-18 (CANL)
    Ignition switch off
    Other
    B



A
Go to step 31
B


26. CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 2 JUNCTION CONNECTOR - POWER STEERING ECU)

  1. C127797E56
    Measure the resistance of the wire harness side connector.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    E75-6 (CANH) - E75-17 (CANL)
    Ignition switch off
    Below 1 Ω
    A
    E75-6 (CANH) - E75-17 (CANL)
    Ignition switch off
    Other
    B



A
Go to step 33
B


27. CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 2 JUNCTION CONNECTOR - MAIN BODY ECU)

  1. C127797E57
    Measure the resistance of the wire harness side connector.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    E75-8 (CANH) - E75-19 (CANL)
    Ignition switch off
    Below 1 Ω
    A
    E75-8 (CANH) - E75-19 (CANL)
    Ignition switch off
    Other
    B



A
Go to step 35
B


28. CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER)

  1. C127797E58
    Measure the resistance of the wire harness side connector.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    E75-4 (CANH) - E75-15 (CANL)
    Ignition switch off
    Below 1 Ω
    A
    E75-4 (CANH) - E75-15 (CANL)
    Ignition switch off
    Other
    B



A
Go to step 37
B

REPAIR OR REPLACE NO. 2 JUNCTION CONNECTOR

29. CONNECT CONNECTOR
  1. Reconnect the E75 No. 2 junction connector.


NEXT


30. CHECK CAN BUS LINES FOR SHORT CIRCUIT (YAW RATE SENSOR)

  1. H100769E34
    Disconnect the K6 yaw rate sensor connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-14 (CANL)
    Ignition switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR (CANH, CANL)
OK

REPLACE YAW RATE SENSOR

31. CONNECT CONNECTOR
  1. Reconnect the E75 No. 2 junction connector.


NEXT


32. CHECK CAN BUS LINES FOR SHORT CIRCUIT (STEERING ANGLE SENSOR)

  1. H100769E34
    Disconnect the E14 steering sensor connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-14 (CANL)
    Ignition switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)
OK

REPLACE STEERING ANGLE SENSOR

33. CONNECT CONNECTOR
  1. Reconnect the E75 No. 2 junction connector.


NEXT


34. CHECK CAN BUS LINES FOR SHORT CIRCUIT (POWER STEERING ECU)

  1. H100769E34
    Disconnect the E21 power steering ECU connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-14 (CANL)
    Ignition switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU (CANH, CANL)
OK

REPLACE POWER STEERING ECU

35. CONNECT CONNECTOR
  1. Reconnect the E75 No. 2 junction connector.


NEXT


36. CHECK CAN BUS LINES FOR SHORT CIRCUIT (MAIN BODY ECU)

  1. H100769E34
    Disconnect the E20 main body ECU connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-14 (CANL)
    Ignition switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)

37. CONNECT CONNECTOR
  1. Reconnect the E75 No. 2 junction connector.


NEXT


38. CHECK CAN BUS LINES FOR SHORT CIRCUIT (AIR CONDITIONING AMPLIFIER)

  1. H100769E34
    Disconnect the E41*1 or E42*2 air conditioning amplifier connector.

    HINT:
    1. *1: for Automatic air conditioning system.
    2. *2: for Manual air conditioning system.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-14 (CANL)
    Ignition switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER (CANH, CANL)
OK

REPLACE AIR CONDITIONING AMPLIFIER

39. CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 4 JUNCTION CONNECTOR - 4WD CONTROL ECU)

NOTICE:
For vehicles without 4WD, go to "CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 4 JUNCTION CONNECTOR - COMBINATION METER ECU)".

  1. C127797E61
    Measure the resistance of the wire harness side connector.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    E76-7 (CANH) - E76-18 (CANL)
    Ignition switch off
    Below 1 Ω
    A
    E76-7 (CANH) - E76-18 (CANL)
    Ignition switch off
    Other
    B



A
Go to step 41
B


40. CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 4 JUNCTION CONNECTOR - COMBINATION METER ECU)

  1. C127797E60
    Measure the resistance of the wire harness side connector.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    E76-5 (CANH) - E76-16 (CANL)
    Ignition switch off
    Below 1 Ω
    A
    E76-5 (CANH) - E76-16 (CANL)
    Ignition switch off
    Other
    B



A
Go to step 43
B

REPAIR OR REPLACE NO. 4 JUNCTION CONNECTOR

41. CONNECT CONNECTOR
  1. Reconnect the E76 No. 4 junction connector.


NEXT


42. CHECK CAN BUS LINES FOR SHORT CIRCUIT (4WD CONTROL ECU)

  1. H100769E34
    Disconnect the E67 4WD control ECU connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-14 (CANL)
    Ignition switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4WD CONTROL ECU (CANH, CANL)
OK

REPLACE 4WD CONTROL ECU

43. CONNECT CONNECTOR
  1. Reconnect the E76 No. 4 junction connector.


NEXT


44. CHECK CAN BUS LINES FOR SHORT CIRCUIT (COMBINATION METER ECU)

  1. H100769E34
    Disconnect the E22 combination meter ECU connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-14 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER (CANH, CANL)
OK

REPLACE COMBINATION METER ECU


← Check CAN Bus Line (RHD Models) (from Aug 2008)Check CAN Bus Lines for Short Circuit (LHD Models) (from Aug 2008) →