2005-2008 RAV4 · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from Nov 2005


1. INSTALL FRONT DIFFERENTIAL SIDE GEAR

C050242E02
  1. Coat the 2 front differential side gears, 2 side gear thrust washers, 2 font differential pinions and 2 pinion thrust washers with ATF and install them to the differential case.


2. INSTALL NO. 1 FRONT DIFFERENTIAL PINION SHAFT

C050241E03
  1. Coat the No. 1 front differential pinion shaft with ATF, and install it to the differential case.


3. INSTALL TRANSAXLE CASE STRAIGHT PIN

C127426
  1. Using a pin punch and a hammer, tap in the pinion shaft straight pin.

  1. C127427
    Using a chisel and a hammer, stake the differential case.

    NOTICE:
    Stake it after adjusting the backlash.


4. INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

C083734E01
  1. Using SST and a press, press in the front differential case rear tapered roller bearing to the differential case.

    SST
    09550-60010  
    09950-60020   (09951-00680)
    09950-70010   (09951-07100)

  1. C083736E02
    Using SST and a hammer, tap in the front differential case tapered roller bearing front outer race to the transaxle housing.
    SST
    09550-60010  
    09950-60020   (09951-00680)
    09950-70010   (09951-07100, 09951-00890)


5. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

C127428
  1. Using SST and a press, press in the front differential case rear tapered roller bearing to the differential case.

    SST
    09550-60010  
    09950-60020   (09951-00680)
    09950-70010   (09951-07100, 09951-00890)

  1. D025603E01
    Using SST and a hammer, tap in the front differential case tapered roller bearing front outer race to the transaxle housing.
    SST
    09550-60010  
    09950-60020   (09951-00680)
    09950-70010   (09951-07100, 09951-00890)

    NOTICE:
    Clearance is not allowed between the bearing and transaxle housing.


6. ADJUST DIFFERENTIAL SIDE BEARING PRELOAD

C127429
  1. Install the differential assembly to the transaxle case.

  1. C050259E01
    Clean the matching surfaces of the transaxle case and transaxle housing.

  1. Install the transaxle housing to the transaxle case and tighten them with the 16 bolts

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf } for bolt A
    29 N*m{ 296 kgf*cm , 21 ft.*lbf } for bolts B and C

    HINT:
    Each bolt length is indicated below.

    Bolt length:
    50 mm (1.969 in.) for bolt A
    50 m (1.969 in.) for bolt B
    42 mm (1.654 in.) for bolt C

    NOTICE:
    Usually, bolt A is non-reusable bolt. In this case, however, it can be used after cleaning it.

  1. D025604E01
    Using SST, return the differential assembly right and left 2 or 3 times to allow the bearing settle.
    SST
    09564-32011  

  1. Using SST and torque wrench, measure the turning torque of the differential.

    SST
    09564-32011  

    Torque:
    Standard turning torque at 60 rpm:
    0.20 to 0.69 N*m{ 2.0 to 7.0 kgf*cm , 1.8 to 6.1 in.*lbf }

    HINT:
    If the turning torque is not within the specified value, refer to the table below and select a thrust washer which turning torque is within the specified value.

    Standard flange thickness:
    Mark
    Thickness
    Mark
    Thickness
    0
    2.00 mm (0.0787 in.)
    9
    2.45 mm (0.0965 in.)
    1
    2.05 mm (0.0807 in.)
    A
    2.50 mm (0.0984 in.)
    2
    2.10 mm (0.0827 in.)
    B
    2.55 mm (0.1004 in.)
    3
    2.15 mm (0.0846 in.)
    C
    2.60 mm (0.1024 in.)
    4
    2.20 mm (0.0866 in.)
    D
    2.65 mm (1.1043 in.)
    5
    2.25 mm (0.0886 in.)
    E
    2.70 mm (0.1063 in.)
    6
    2.30 mm (0.0906 in.)
    F
    2.75 mm (0.1083 in.)
    7
    2.35 mm (0.0925 in.)
    G
    2.80 mm (0.1102)
    8
    2.40 mm (0.0945 in.)
    H
    2.85 mm (0.1122 in.)

  1. C050259E02
    Remove the 16 bolts and the transaxle housing.

  1. C127429
    Remove the differential assembly.


7. INSTALL FRONT DIFFERENTIAL RING GEAR

D025215E03
  1. Using ATF and a heater, heat the front differential ring gear to 90 to 110 °C (194.0 to 230.0 °F)

    NOTICE:
    Do not overheat the ring gear to 110°C (230.0°F) or more.

  1. Clean the contract surface of the front differential case.

  1. C126601E01
    Align the matchmarks, and install the front differential ring gear case quickly.

    NOTICE:
    Do not install the bolts while the ring gear is hot.

  1. C127422
    Tighten the 14 bolts.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }

    NOTICE:
    Tighten the bolts a little at a time in diagonal order.


8. INSTALL DIFFERENTIAL SIDE BEARING RETAINER OIL SEAL

C083738E01
  1. Coat the lip of a new oil seal with a little amount of MP grease.

  1. Using SST and a hammer, tap in the oil seal.

    SST
    09223-15020  
    09950-70010   (09951-07100)


9. REMOVE TRANSAXLE HOUSING OIL SEAL

D025606E01
  1. Coat the lip of a new oil seal with a little amount of MP grease.

  1. Using SST and a hammer, tap in the oil seal.

    SST
    09710-30050  
    09950-70010   (09951-07100)

← INSPECTION (from Nov 2005)COMPONENTS (from Nov 2005) →