Steering Lock Motor Drive Power Circuit
Circuit diagnosis · Vehicles built from Nov 2005
DESCRIPTION
The main body ECU supplies the power to activate the motor of the steering lock actuator assembly.The diagnosis information of the steering lock ECU is transmitted to the tester via the certification ECU as the steering lock ECU is not connected to the CAN communication system.
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- When the engine switch is off, the main body ECU may occasionally go into a non-active state called sleep mode. Therefore, before proceeding with the inspection, it is necessary to perform the following step to wake up the ECU:
- Before starting the inspection, with the engine switch off, open the driver door. Then (with the engine switch still off) open and close any door several times at 1.5 second intervals.
| 1. CHECK DTC (CERTIFICATION ECU) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and press the intelligent tester main switch ON.
Read the DTCs of the certification ECU by following the prompts displayed on the intelligent tester.
- OK:
- DTC is not output.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (CERTIFICATION ECU) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and press the intelligent tester main switch ON.
Select the item "Lock/Unlock Receive" in the Data List within 10 seconds of starting the engine and read the value displayed on the intelligent tester.
Certification ECU Item
Measurement Item / Range (Display)
Normal Condition
Diagnostic Note
Lock/Unlock Receive
Steering lock command reception record / YES or NO
YES: Steering lock/unlock signal received
NO: Steering lock/unlock signal not received
-
- OK:
- YES is displayed on the tester screen.
|
|
||||
| OK | |
| 3. CHECK STEERING LOCK ACTUATOR |
![]() ![]() |
Measure the resistance and voltage of the steering lock actuator.
- Standard resistance:
Tester Connection
Specified Condition
E6-1 (GND) - Body ground
Below 1 Ω
E6-2 (SGND) - Body ground
Below 1 Ω
- Standard voltage:
Tester Connection
Specified Condition
E6-7 (B) - E6-1 (GND)
10 to 14 V
E6-7 (B) - E6-2 (SGND)
10 to 14 V
|
|
||||
| OK | |
| 4. CHECK STEERING LOCK ACTUATOR |
![]() ![]() |
Immediately after turning the engine switch on (IG), inspect the voltage between terminals E6-3 (IGE) and E6-2 (SGND) of the steering lock actuator.
Result Result
Proceed to
Immediately after turning engine switch on (IG), condition that measurement is 1 V or less occurs
A
Measurement is 10 to 14 V, and measurement never becomes 1 V or less
B
|
|
||||
| A | ||
| ||
| 5. READ VALUE USING INTELLIGENT TESTER (CERTIFICATION ECU) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and press the intelligent tester main switch ON.
Select the item "S Code Check" in the Data List and read the value displayed on the intelligent tester.
Certification ECU Item
Measurement Item / Range (Display)
Normal Condition
Diagnostic Note
S Code Check
S code match record / NG or OK
NG: S code not matched
OK: S code matched
-
- OK:
- YES is displayed on the tester screen.
|
|
||||
| NG | |
| 6. CHECK OPERATION OF ID CODE BOX |
Replace the ID code box with a normally functioning or new one.
Reconfirm the item "S Code Check" in the Data List and read the value displayed on the intelligent tester.
Certification ECU Item
Measurement Item / Range (Display)
Normal Condition
Diagnostic Note
S Code Check
S code match record / NG or OK
NG: S code not matched
OK: S code matched
-
- OK:
- OK is displayed on the tester screen.
|
|
||||
| NG | ||
| ||
| 7. READ VALUE USING INTELLIGENT TESTER (CERTIFICATION ECU) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and press the intelligent tester main switch ON.
Select the item "L Code Check" in the Data List and read the value displayed on the intelligent tester.
Certification ECU Item
Measurement Item / Range (Display)
Normal Condition
Diagnostic Note
L Code Check
L code match record / NG or OK
NG: L code not matched
OK: L code matched
-
- OK:
- OK is displayed on the tester screen.
|
|
||||
| NG | |
| 8. CHECK OPERATION OF ID CODE BOX |
Replace the ID code box with a normally functioning or new one.
Reconfirm the item "L Code Check" in the Data List and read the value displayed on the intelligent tester.
Certification ECU Item
Measurement Item / Range (Display)
Normal Condition
Diagnostic Note
L Code Check
L code match record / NG or OK
NG: L code not matched
OK: L code matched
-
- OK:
- OK is displayed on the tester screen.
|
|
||||
| NG | |
| 9. CHECK OPERATION OF STEERING LOCK ACTUATOR |
Replace the steering lock actuator assembly with a normally functioning or new one.
Turn the engine switch on (IG).
Check the steering lock.
- OK:
- Steering lock is released and engine starts.
|
|
||||
| NG | ||
| ||


