2005-2008 RAV4 · Service Manual SECURITIES

B2796 No Communication in Immobiliser System

Diagnostic trouble codes · Vehicles built from Nov 2005

Also covers:

DESCRIPTION

When a key is inserted into the ignition key cylinder but no communication occurs between the key and transponder key ECU, DTC B2796 is output. When a key is inserted into the ignition key cylinder but a communication error occurs between the key and transponder key ECU, DTC B2798 is output.
DTC No.
DTC Detection Condition
Trouble Area
B2796
No communication
  1. Transponder key ECU
  2. Key
  3. Wire harness
  4. Transponder key amplifier
B2798
Communication error
Key

WIRING DIAGRAM

B121682E05

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (ENGINE IMMOBILISER SYSTEM)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) with a key that cannot start the engine.

  1. On the intelligent tester, enter the following menus: Body / Engine Immobiliser / Data List / Immobiliser. Read the result.

    Transponder key ECU: 
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnostic Note
    Immobiliser
    Immobiliser system status / SET or UNSET
    UNSET: Key is in ignition key cylinder
    SET: No key is in ignition key cylinder
    -

    OK:
    UNSET (key is in ignition key cylinder) appears on the screen.



OK
REPLACE TRANSPONDER KEY ECU
NG


2. CHECK WHETHER ENGINE STARTS WITH OTHER KEY
  1. Check whether the engine starts with the vehicle's other keys.

    OK:
    Engine starts.



NG
REREGISTER OR REPLACE KEY THAT CANNOT START ENGINE
OK


3. READ VALUE USING INTELLIGENT TESTER (TRANSPONDER KEY COIL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) with a key that cannot start the engine.

  1. On the intelligent tester, enter the following menus: Body / Engine Immobiliser / Data List / Antenna Coil Status. Read the result.

    Transponder key ECU: 
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnostic Note
    Antenna Coil Status
    Transponder key coil condition/ NORMAL or FAIL
    NORMAL: Transponder key coil is normal
    FAIL: Transponder key coil is malfunctioning
    -

    OK:
    NORMAL (Transponder key coil is normal) appears on the screen.



OK
REPLACE TRANSPONDER KEY ECU
NG


4. CHECK WIRE HARNESS (TRANSPONDER KEY ECU - TRANSPONDER KEY AMPLIFIER)
B110403E21
  1. Disconnect the E50 ECU connector.

  1. Disconnect the E8 amplifier connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    E50-14 (VC5) - E8-1 (VC5)
    Below 1 Ω
    E50-15 (CODE) - E8-4 (CODE)
    E50-4 (TXCT) - E8-5 (TXCT)
    E50-5 (AGND) - E8-7 (AGND)
    E50-14 (VC5) or E8-1 (VC5) - Body ground
    10 kΩ or higher
    E50-15 (CODE) or E8-4 (CODE) - Body ground
    E50-4 (TXCT) or E8-5 (TXCT) - Body ground
    E50-5 (AGND) or E8-7 (AGND) - Body ground



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5. CHECK TRANSPONDER KEY AMPLIFIER (OPERATION)
  1. Temporarily replace the transponder key amplifier with a new or normally functioning one.

  1. Check that the engine starts normally.

    OK:
    Engine starts normally.



NG
REPLACE TRANSPONDER KEY ECU
OK

END (TRANSPONDER KEY AMPLIFIER IS DEFECTIVE)


← B2795 Unmatched Key Code (from Aug 2007)B2797 Communication Malfunction No. 1 (Nov 2005 – Dec 2006) →