2005-2008 RAV4 · Service Manual COMMUNICATION SYSTEM

Check CAN Bus Line for Short to +B (RHD Models)

Circuit diagnosis · Vehicles built Nov 2005 – Jul 2008

Versions by build date: Nov 2005 – Jul 2008 from Aug 2008

DESCRIPTION

There may be a short circuit between the CAN bus line and +B when there is resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3.
Symptom
Trouble Area
There is resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of DLC3.
  1. Short to +B
  2. Brake actuator (skid control ECU)*1
  3. ABS and traction actuator (skid control ECU)*2
  4. Power steering ECU
  5. Steering angle sensor*4
  6. Yaw rate sensor*2
  7. ECM
  8. Center airbag sensor assembly
  9. Combination meter ECU
  10. Air conditioning amplifier
  11. Instrument panel junction block (Main body ECU)
  12. 4WD control ECU*3

HINT:
*1: w/ ABS
*2: w/ VSC
*3: for 4WD
*4: for 2WD with VSC and 4WD


WIRING DIAGRAM

C132857E02
C163577E01

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the main wire and the branch wire.
  2. For Auto:
    After the ignition switch is turned off, check that the key reminder warning system is not in operation.
  3. For Reminder:
    After the ignition switch is turned off, check that the key reminder warning system and light reminder buzzer are not in operation.
  4. Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. CHECK CAN BUS LINE FOR SHORT TO +B (DLC3 BRANCH WIRE)

  1. H100769E35
    Disconnect the E89 No. 4 junction connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


2. CONNECT CONNECTOR
  1. Reconnect the E89 No. 4 junction connector.


NEXT


3. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 1 JUNCTION CONNECTOR SIDE)

  1. H100769E35
    Disconnect the A51 No. 1 junction connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



OK
Go to step 18
NG


4. CONNECT CONNECTOR
  1. Reconnect the A51 No. 1 junction connector.


NEXT


5. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 1 JUNCTION CONNECTOR, NO. 2 JUNCTION CONNECTOR SIDE)

  1. H100769E35
    Disconnect the E87 No. 2 junction connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



OK
Go to step 27
NG


6. CONNECT CONNECTOR
  1. Reconnect the E87 No. 2 junction connector.


NEXT


7. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 1 JUNCTION CONNECTOR, NO. 2 JUNCTION CONNECTOR, NO. 3 JUNCTION CONNECTOR SIDE)

  1. H100769E35
    Disconnect the E77 No. 3 junction connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



OK
Go to step 33
NG


8. CONNECT CONNECTOR
  1. Reconnect the E77 No. 3 junction connector.


NEXT


9. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 4 JUNCTION CONNECTOR - 4WD CONTROL ECU)

NOTICE:
For vehicles without 4WD, go to "CHECK CAN BUS LINE FOR SHORT TO +B (NO. 4 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)".

  1. C133164E84
    Disconnect the E88 No. 4 junction connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E88-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    E88-17 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



NG
Go to step 12
OK


10. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 4 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)

NOTICE:
For vehicles without 2WD with VSC and 4WD, go to "CHECK CAN BUS LINE FOR SHORT TO +B (NO. 4 JUNCTION CONNECTOR - COMBINATION METER ECU)".

  1. C133164E85
    Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E88-7 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    E88-18 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



NG
Go to step 14
OK


11. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 4 JUNCTION CONNECTOR - COMBINATION METER ECU)

  1. C133164E86
    Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E88-5 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    E88-16 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



NG
Go to step 16
OK

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)

12. CONNECT CONNECTOR
  1. Reconnect the E88 No. 4 junction connector.


NEXT


13. CHECK CAN BUS LINE FOR SHORT TO +B (4WD CONTROL ECU)

  1. H100769E35
    Disconnect the E67 4WD control ECU connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4WD CONTROL ECU (CANH, CANL)
OK

REPLACE 4WD CONTROL ECU

14. CONNECT CONNECTOR
  1. Reconnect the E88 No. 4 junction connector.


NEXT


15. CHECK CAN BUS LINE FOR SHORT TO +B (STEERING ANGLE SENSOR)

  1. H100769E35
    Disconnect the E14 steering angle sensor connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)
OK

REPLACE STEERING ANGLE SENSOR

16. CONNECT CONNECTOR
  1. Reconnect the E88 No. 4 junction connector.


NEXT


17. CHECK CAN BUS LINE FOR SHORT TO +B (COMBINATION METER ECU)

  1. H100769E35
    Disconnect the E22 combination meter ECU connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ECU (CANH, CANL)
OK

REPLACE COMBINATION METER ECU

18. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 1 JUNCTION CONNECTOR - BRAKE ACTUATOR)

NOTICE:
For vehicles without ABS, go to "CHECK CAN BUS LINE FOR SHORT TO +B (NO. 1 JUNCTION CONNECTOR - ABS AND TRACTION ACTUATOR)".

  1. C133164E87
    Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A51-1 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    A51-12 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



NG
Go to step 21
OK


19. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 1 JUNCTION CONNECTOR - ABS AND TRACTION ACTUATOR)

NOTICE:
For vehicles without VSC, go to "CHECK CAN BUS LINE FOR SHORT TO +B (NO. 1 JUNCTION CONNECTOR - ECM)".

  1. C133164E88
    Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A51-1 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    A51-12 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



NG
Go to step 23
OK


20. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 1 JUNCTION CONNECTOR - ECM)

  1. C133164E89
    Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A51-2 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    A51-13 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



NG
Go to step 25
OK

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

21. CONNECT CONNECTOR
  1. Reconnect the A51 No. 1 junction connector.


NEXT


22. CHECK CAN BUS LINE FOR SHORT TO +B (BRAKE ACTUATOR)

  1. H100769E35
    Disconnect the A27 brake actuator (skid control ECU) connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BRAKE ACTUATOR (CANH, CANL)
OK

REPLACE BRAKE ACTUATOR (SKID CONTROL ECU)

23. CONNECT CONNECTOR
  1. Reconnect the A51 No. 1 junction connector.


NEXT


24. CHECK CAN BUS LINE FOR SHORT TO +B (ABS AND TRACTION ACTUATOR)

  1. H100769E35
    Disconnect the A26 ABS and traction actuator (skid control ECU) connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO ABS AND TRACTION ACTUATOR (CANH, CANL)
OK

REPLACE ABS AND TRACTION ACTUATOR (SKID CONTROL ECU)

25. CONNECT CONNECTOR
  1. Reconnect the A51 No. 1 junction connector.


NEXT


26. CHECK CAN BUS LINE FOR SHORT TO +B (ECM)

  1. H100769E35
    Disconnect the A12 ECM connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
OK

REPLACE ECM

27. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 2 JUNCTION CONNECTOR - YAW RATE SENSOR)

NOTICE:
For vehicles without VSC, go to "CHECK CAN BUS LINE FOR SHORT TO +B (NO. 2 JUNCTION CONNECTOR - MAIN BODY ECU)".

  1. C133164E90
    Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A51-2 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    A51-13 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



NG
Go to step 29
OK


28. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 2 JUNCTION CONNECTOR - MAIN BODY ECU)

  1. C133164E91
    Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A51-5 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    A51-16 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



NG
Go to step 31
OK

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

29. CONNECT CONNECTOR
  1. Reconnect the E87 No. 2 junction connector.


NEXT


30. CHECK CAN BUS LINE FOR SHORT TO +B (YAW RATE SENSOR)

  1. H100769E35
    Disconnect the K6 yaw rate sensor connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR (CANH, CANL)
OK

REPLACE YAW RATE SENSOR

31. CONNECT CONNECTOR
  1. Reconnect the E87 No. 2 junction connector.


NEXT


Go to step 30

32. CHECK CAN BUS LINE FOR SHORT TO +B (MAIN BODY ECU)

  1. H100769E35
    Disconnect the E20 main body ECU connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)

33. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 3 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER)

  1. C133164E92
    Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A51-2 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    A51-13 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



NG
Go to step 36
OK


34. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 3 JUNCTION CONNECTOR - POWER STEERING ECU)

  1. C133164E93
    Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A51-4 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    A51-15 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



NG
Go to step 38
OK


35. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 3 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)

  1. C133164E94
    Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A51-1 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    A51-12 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



NG
Go to step 40
OK


36. CONNECT CONNECTOR
  1. Reconnect the E77 No. 3 junction connector.


NEXT


37. CHECK CAN BUS LINE FOR SHORT TO +B (AIR CONDITIONING AMPLIFIER)

  1. H100769E35
    Disconnect the E41*1 or E42*2 air conditioning amplifier connector.

    HINT:
    1. *1: for Automatic air conditioning system.
    2. *2: for Manual air conditioning system.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER (CANH, CANL)
OK

REPLACE AIR CONDITIONING AMPLIFIER

38. CONNECT CONNECTOR
  1. Reconnect the E77 No. 3 junction connector.


NEXT


39. CHECK CAN BUS LINE FOR SHORT TO +B (POWER STEERING ECU)

  1. H100769E35
    Disconnect the E21 power steering ECU connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU (CANH, CANL)
OK

REPLACE POWER STEERING ECU

40. CONNECT CONNECTOR
  1. Reconnect the E77 No. 3 junction connector.


NEXT


41. CHECK CAN BUS LINE FOR SHORT TO +B (CENTER AIRBAG SENSOR ASSEMBLY)

  1. H100769E35
    Disconnect the E49 center airbag sensor connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CANH, CANL)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY


← Check CAN Bus Line for Short to GND (LHD Models) (from Aug 2008)Check CAN Bus Line for Short to +B (RHD Models) (from Aug 2008) →