TERMINALS OF ECU
System information · Vehicles built from Nov 2005
| CHECK ECU AGGREGATION BOX (CERTIFICATION ECU) |


Disconnect the E63 ECU connector.
Measure the resistance and voltage of the wire harness side connector.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
E (E63-17) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
+B1 (E63-1) - Body ground
R - Body ground
+B power supply
Always
10 to 14 V
IG (E63-18) - Body ground
B - Body ground
Ignition power supply
Ignition switch off
Below 1 V
Ignition switch on (IG)
10 to 14 V
TSW1 (E63-3) - E (E63-17)
V - W-B
Door outside handle (driver side) lock switch signal
Switch released
10 kΩ or higher
Switch pressed in
Below 1 Ω
TSW2 (E63-4) - E (E63-17)
R - W-B
Door outside handle (passenger side) lock switch signal
Switch released
10 kΩ or higher
Switch pressed in
Below 1 Ω
TSW9 (E63-7) - E (E63-17)
LG - W-B
Back door outside handle unlock switch signal
Switch released
10 kΩ or higher
Switch pressed in
Below 1 Ω
LIN (E63-10) - E (E63-17)
V - W-B
LIN line
Always
10 kΩ or higher
- If the result is not as specified, the wire harness side may have a malfunction.
- If the result is not as specified, the wire harness side may have a malfunction.
Reconnect the E63 ECU connector.
Measure the voltage of the connector.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
CLG1 (E63-33) - CG1B (E63-34)
R - B
Door electrical key oscillator (driver side) sensor signal
All doors closed, all doors locked and Ignition switch off
Alternating between 5 V and below 1 V
Door unlocked or door open
Below 1 V
SEN1 (E63-22) - E (E63-17)
R - W-B
Touch sensor detection signal
Outside door handle touched
10 to 14 V
Outside door handle not touched
Below 1 V
SEL1 (E63-5) - E (E63-17)
Y - W-B
Touch sensor activation control signal
Key at least 3 m (9.8 ft.) away from door
10 to 14 V
Close to door
Below 1 V
CLG2 (E63-35) - CG2B (E63-36)
B - R
Door electrical key oscillator (passenger side) sensor signal
All doors closed, all doors locked and ignition switch off
Alternating between 5 V and below 1 V
Door unlocked or door open
Below 1 V
SEN2 (E63-23) - E (E63-17)
W - W-B
Touch sensor detection signal
Outside door handle touched
10 to 14 V
Outside door handle not touched
Below 1 V
SEL2 (E63-6) - E (E63-17)
B - W-B
Touch sensor activation control signal
Key at least 3 m (9.8 ft.) away from door
10 to 14 V
Close to door
Below 1 V
CLG5 (E63-11) - CG5B (E63-12)
R - G
Indoor electrical key oscillator (front) sensor signal
30 seconds after driver side door opened and closed, ignition switch off
Alternating between 5 V and below 1 V
Within 30 seconds driver side door opened and closed, ignition switch off
Below 1 V
CLG7 (E63-15) - CG7B (E63-16)
W - B
Indoor electrical key oscillator (rear) sensor signal
30 seconds after driver side door opened and closed, ignition switch off
Alternating between 5 V and below 1 V
Within 30 seconds driver side door opened and closed, ignition switch off
Below 1 V
CLG9 (E63-31) - CG9B (E63-32)
B - W
Door electrical key oscillator (back door) sensor signal
Back door unlock switch OFF
Alternating between 5 V and below 1 V
Back door unlock switch ON
Below 1 V
RCO (E63-29) - E (E63-17)
V - W-B
Door control receiver power source
All doors closed, all doors locked and ignition switch off
0 to 6 V
Door unlocked or door open
Below 1 V
RSSI (E63-39) - E (E63-17)
R - W-B
Door control receiver electric wave existence signal
All doors closed, all doors locked and ignition switch off
0 to 5 V
Door unlocked or door open
Below 1 V
RDA (E63-38) - E (E63-17)
Y - W-B
Door control receiver data input signal
All doors closed, all doors locked and ignition switch off
Below 1 V
Door unlocked or door open
Approx. 6 to 7 V
- If the result is not as specified, the ECU may have a malfunction.
- If the result is not as specified, the ECU may have a malfunction.
| CHECK DOOR ELECTRICAL KEY OSCILLATOR (for FRONT DOOR) |


Disconnect the Y2 or Z2 oscillator connector.
Measure the resistance and voltage of the wire harness side connector.
Front door RH side: Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
GND (Y2-7) - Body ground
BR - Body ground
Ground
Always
Below 1 Ω
+B (Y2-1) - GND (Y2-7)
Y - BR
+B power supply
Always
10 to 14 V
Front door LH side: Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
GND (Z2-7) - Body ground
G-R - Body ground
Ground
Always
Below 1 Ω
+B (Z2-1) - GND (Z2-7)
Y - BR
+B power supply
Always
10 to 14 V
- If the result is not as specified, the wire harness side may have a malfunction.
- If the result is not as specified, the wire harness side may have a malfunction.
Reconnect the Y2 or Z2 oscillator connector.
Measure the voltage of the wire harness side connector.
Front door LH side: Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
CLG (Z2-1) - GND (Z2-7)
R - BR
Door electrical key oscillator (driver side) sensor signal
All doors closed, all doors locked and ignition switch off
Alternating between 5 V and below 1 V
Door unlocked or door open
Below 1 V
SEL (Z2-4) - GND (Z2-7)
O - BR
Touch sensor activation control signal
Key at least 3 m (9.8 ft.) away from door
10 to 14 V
Close to door
Below 1 V
SENS (Z2-6) - GND (Z2-7)
V - BR
Touch sensor detection signal
Outside door handle touched
10 to 14 V
Outside door handle not touched
Below 1 V
Front door RH side: Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
CLG (Y2-1) - GND (Y2-7)
R - BR
Door electrical key oscillator sensor signal
All doors closed, all doors locked and ignition switch off
Alternating between 5 V and below 1 V
Door unlocked or door open
Below 1 V
SEL (Y2-4) - GND (Y2-7)
O - BR
Touch sensor activation control signal
Key at least 3 m (9.8 ft.) away from door
10 to 14 V
Close to door
Below 1 V
SENS (Y2-6) - GND (Y2-7)
V - BR
Touch sensor detection signal
Outside door handle touched
10 to 14 V
Outside door handle not touched
Below 1 V
- If the result is not as specified, the oscillator may have a malfunction.
- If the result is not as specified, the oscillator may have a malfunction.
| CHECK DOOR ELECTRICAL KEY OSCILLATOR (for Back Door) |


Measure the voltage of the wire harness side connector.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
CLG (S8-10) - CLGB (S8-5)
B - W
Door electrical key oscillator (back door) sensor signal
Back door unlock switch OFF
Alternating between 5 V and below 1 V
Back door unlock switch ON
Below 1 V
- If the result is not as specified, the oscillator may have a malfunction.
- If the result is not as specified, the oscillator may have a malfunction.
| CHECK INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU) |




Disconnect the IB, ID, IE, and IF junction block connectors.
Disconnect the E18, E19 and E20 ECU connectors.
Measure the resistance and voltage of the wire harness side connectors.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
GND1(IE-17) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
GND2 (E19-4) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
BECU (IB-30) - Body ground
R - Body ground
+B power supply
Always
10 to 14 V
AM1 (E19-1) - Body ground
W - Body ground
+B power supply
Always
10 to 14 V
AM2 (E18-6) - Body ground
W - Body ground
+B power supply
Always
10 to 14 V
IG (IF-3) - Body ground
P - Body ground
IG1 signal
Ignition switch on (IG)
10 to 14 V
Ignition switch off
Below 1 V
ACC (IS-4) - Body ground
GR - Body ground
ACC signal
Ignition switch on (ACC)
10 to 14 V
CANH (E20-15) - Body ground
R - Body ground
CAN communication line
Always
10 kΩ or higher
CANL (E20-16) - Body ground
W - Body ground
CAN communication line
Always
10 kΩ or higher
LIN1(ID-9) - Body ground
V - Body ground
LIN communication line
Always
10 kΩ or higher
- If the result is not as specified, the wire harness side may have a malfunction.
- If the result is not as specified, the wire harness side may have a malfunction.
Reconnect the IB, ID, IE and IF junction block connectors.
Reconnect the E18, E19 and E20 ECU connectors.
Measure the voltage of the connectors.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
DCTY (IA-21)*1 - Body ground
DCTY (IC-6)*2 - Body ground
W*1 - Body ground
BR*2 - Body ground
Driver side door courtesy light switch input
Driver side door closed
10 to 14 V
Driver side door open
Below 1 V
PCTY (IC-14)*1 - Body ground
PCTY (IA-24)*2 - Body ground
BR*1 - Body ground
W*2 - Body ground
Passenger side door courtesy light switch input
Passenger side door closed
10 to 14 V
Passenger side door open
Below 1 V
RCTY (ID-7) - Body ground
LG- Body ground
Rear RH door courtesy light switch input
Rear RH door closed
10 to 14 V
Rear RH door open
Below 1 V
LCTY (E18-8) - Body ground
SB - Body ground
Rear LH door courtesy light switch input
Rear LH door closed
10 to 14 V
Rear LH door open
Below 1 V
B+ (IA-7) - Body ground
LG- Body ground
Back door courtesy light switch input
Back side door closed
10 to 14 V
Back side door open
Below 1 V
HAZ (IS-17) - Body ground
GR- Body ground
Hazard warning light signal
Answer-back ON
Below 1 V
Answer-back OFF
10 to 14 V
- HINT:
- *1: for LHD
- *2: for RHD
- If the result is not as specified, the main body ECU may have a malfunction.