TERMINALS OF ECU
System information · Vehicles built from Nov 2005
| CHECK INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU) |




Disconnect the IB and IE junction block connectors.
Measure the resistance and voltage of the wire harness side connectors.
If the result is not as specified, there may be a malfunction in the wire harness.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
GND1 (IE-17) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
BECU (IB-30) - GND1 (IE-17)
R - W-B
Battery (power supply)
Always
10 to 14 V
Reconnect the IB and IE junction block connectors.
Measure the voltage of the wire harness side connectors.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
DCTY (IA-21)*1 - Body ground
DCTY (IC-6)*2 - Body ground
W*1 - Body ground
BR*2 - Body ground
Driver side door courtesy switch input
Driver side door closed
10 to 14 V
Driver side door open
Below 1 V
PCTY (IC-14)*1 - Body ground
PCTY (IA-24)*2 - Body ground
BR*1 - Body ground
W*2 - Body ground
Passenger side door courtesy switch input
Passenger side door closed
10 to 14 V
Passenger side door open
Below 1 V
RCTY (ID-7) - Body ground
LG - Body ground
Rear RH door courtesy switch input
Rear RH door closed
10 to 14 V
Rear RH door open
Below 1 V
LCTY (B18-8) - Body ground
SB - Body ground
Rear LH door courtesy switch input
Rear LH door closed
10 to 14 V
Rear LH door open
Below 1 V
B+ (IA-7) - Body ground
LG- Body ground
Back door courtesy switch input
Back side door closed
10 to 14 V
Back side door open
Below 1 V
L1 (IH-4)*1 - Body ground
L1 (IH-13)*2 - Body ground
P*1 - Body ground
V*2 - Body ground
Door lock motor LOCK drive output
Master switch (door control switch) OFF
Below 1 V
Master switch (door control switch) ON (LOCK)
10 to 14 V → Below 1 V
UL1 (IH-5)*1 - Body ground
UL1 (IH-14)*2 - Body ground
B*1 - Body ground
O*2 - Body ground
Door lock motor UNLOCK drive output
Master switch (door control switch) OFF
Below 1 V
Master switch (door control switch) ON (UNLOCK)
10 to 14 V → Below 1 V
ACT+ (IH-8)*1 - Body ground
ACT+ (IH-17)*2 - Body ground
R - Body ground
Door lock motor LOCK drive output
Master switch (door control switch) or driver side door key cylinder OFF
Below 1 V
Master switch (door control switch) or driver side door key cylinder ON (LOCK)
10 to 14 V → Below 1 V
ACT- (IH-18)*1 - Body ground
ACT- (IH-9)*2 - Body ground
B - Body ground
Door lock motor UNLOCK drive output
Master switch (door control switch) or driver side door key cylinder OFF
Below 1 V
Master switch (door control switch) or driver side door key cylinder ON (UNLOCK)
10 to 14 V → Below 1 V
LSWD (E18-25) - Body ground
Y - Body ground
Driver side door lock position switch input
Driver side door UNLOCK
Below 1 V
Driver side door LOCK
10 to 14 V
LSWP (E18-10) - Body ground
Y - Body ground
Passenger side door lock position switch input
Passenger side door UNLOCK
Below 1 V
Passenger side door LOCK
10 to 14 V
UL2 (IH-6)*1 - Body ground
UL2 (IH-15)*2 - Body ground
LG*1 - Body ground
L*2 - Body ground
Door lock motor UNLOCK drive output
Passenger side door key cylinder OFF
Below 1 V
Passenger side door key cylinder ON (UNLOCK)
10 to 14 V → Below 1 V
L2 (IH-7)*1 - Body ground
L2 (IH-16)*2 - Body ground
SB*1 - Body ground
R*2 - Body ground
Door lock motor LOCK drive output
Master switch or driver side door key cylinder OFF
Below 1 V
Master switch or driver side door key cylinder ON (LOCK)
10 to 14 V → Below 1 V
HAZ (IS-17) - Body ground
GR - Body ground
Hazard warning light signal
Answer-back ON
Pulse generation
Answer-back OFF
10 to 14 V
- HINT:
- *1: for LHD
- *2: for RHD
| CHECK CERTIFICATION ECU |


Disconnect the E63 ECU connector.
Measure the resistance and voltage of the wire harness side connector.
If the result is not as specified, there may be a malfunction in the wire harness.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
E (E63-17) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
+B1 (E63-1) - Body ground
R - Body ground
+B power supply
Always
10 to 14 V
IG (E63-18) - Body ground
B - Body ground
Ignition power supply
Ignition switch on (IG)
10 to 14 V
Ignition switch off
Below 1 V
LIN (E63-10) - Body ground
V - Body ground
LIN line
Always
10 kΩ or higher
RSSI (E63-39) - Body ground
R - Body ground
Door control receiver output
Ignition switch off, all doors closed and transmitter switch not pressed → pressed
10 to 14 V → Below 1 V
RDA (E63-38) - Body ground
Y - Body ground
Door control receiver input
Ignition switch off, all doors closed and transmitter switch not pressed → pressed
Below 1 V → 10 to 14 V → Below 1 V
RCO (E63-29) - Body ground
V - Body ground
Door control receiver input
Ignition switch off, all doors closed and transmitter switch not pressed → pressed
5 to Below 1 V → 5 V