2005-2008 RAV4 · Service Manual BODY ELECTRICAL

TERMINALS OF ECU

System information · Vehicles built from Nov 2005


CHECK INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)
E114510E18
B108612E14
  1. Disconnect the IB and IE junction block connectors.

  2. Measure the resistance and voltage of the wire harness side connectors.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    GND (IE-17) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    B (IB-30) - GND (IE-17)
    R - W-B
    Battery (power supply)
    Always
    10 to 14 V
    1. If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the IB and IE junction block connectors.

  4. Measure the voltage of the wire harness side connectors.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    KSW (IE-26) - GND (IE-17)
    L- W-B
    Key unlock warning switch input
    Key inserted
    10 to 14 V
    No key in ignition key cylinder
    Below 1 V
    DCTY (IC-6) - Body ground
    BR - Body ground
    Driver side door courtesy switch input
    Driver side door closed
    10 to 14 V
    Driver side door open
    Below 1 V
    PCTY (IC-14)*1 - Body ground
    PCTY (IA-24)*2 - Body ground
    BR*1 - Body ground
    W*2 - Body ground
    Passenger side door courtesy switch input
    Passenger side door closed
    10 to 14 V
    Passenger side door open
    Below 1 V
    RCTY (ID-7) - Body ground
    LG - Body ground
    Rear RH door courtesy switch input
    Rear RH door closed
    10 to 14 V
    Rear RH door open
    Below 1 V
    LCTY (E18-8) - Body ground
    SB - Body ground
    Rear LH door courtesy switch input
    Rear LH door closed
    10 to 14 V
    Rear LH door open
    Below 1 V
    B+ (IA-7) - Body ground
    LG- Body ground
    Back door courtesy switch input
    Back side door closed
    10 to 14 V
    Back side door open
    Below 1 V
    L1 (IH-4)*1 - Body ground
    L1 (IH-13)*2 - Body ground
    P*1 - Body ground
    V*2 - Body ground
    Door lock motor LOCK drive output
    Master switch (door control switch) OFF
    Below 1 V
    Master switch (door control switch) ON (LOCK)
    10 to 14 V → Below 1 V
    UL1 (IH-5)*1 - Body ground
    UL1 (IH-14)*2 - Body ground
    B*1 - Body ground
    O*1 - Body ground
    Door lock motor UNLOCK drive output
    Master switch (door control switch) OFF
    Below 1 V
    Master switch (door control switch) ON (UNLOCK)
    10 to 14 V → Below 1 V
    ACT+ (IH-8)*1 - Body ground
    ACT+ (IH-17)*2 - Body ground
    R - Body ground
    Door lock motor LOCK drive output
    Master switch (door control switch) or driver side door key cylinder OFF
    Below 1 V
    Master switch (door control switch) or driver side door key cylinder ON (LOCK)
    10 to 14 V → Below 1 V
    ACT- (IH-18)*1 - Body ground
    ACT- (IH-9)*2 - Body ground
    B - Body ground
    Door lock motor UNLOCK drive output
    Master switch (door control switch) or driver side door key cylinder OFF
    Below 1 V
    Master switch (door control switch) or driver side door key cylinder ON (UNLOCK)
    10 to 14 V → Below 1 V
    LSWD (E18-25) - Body ground
    Y - Body ground
    Driver side door lock position switch input
    Driver side door UNLOCK
    Below 1 V
    Driver side door LOCK
    10 to 14 V
    LSWP (E18-10) - Body ground
    L - Body ground
    Passenger side door lock position switch input
    Passenger side door UNLOCK
    Below 1 V
    Passenger side door LOCK
    10 to 14 V
    UL2 (IH-6)*1 - Body ground
    UL2 (IH-15)*2 - Body ground
    LG*1 - Body ground
    L*2 - Body ground
    Door lock motor UNLOCK drive output
    Passenger side door key cylinder OFF
    Below 1 V
    Passenger side door key cylinder ON (UNLOCK)
    10 to 14 V → Below 1 V
    L2 (IH-7)*1 - Body ground
    L2 (IH-16)*2 - Body ground
    SB*1 - Body ground
    R*2 - Body ground
    Door lock motor LOCK drive output
    Master switch or driver side door key cylinder OFF
    Below 1 V
    Master switch or driver side door key cylinder ON (LOCK)
    10 to 14 V → Below 1 V
    PRG (E20-6) - Body ground
    Y - Body ground
    Door control receiver output
    Key inserted in ignition key cylinder → As key pulled out of ignition key cylinder
    11 to 14 V → Pulse generation → 11 to 14 V
    RDA (E20-5) - Body ground
    G - Body ground
    Door control receiver input
    Ignition switch off, all doors closed and transmitter switch not pressed
    11 to 14 V
    Ignition switch off, all doors closed and transmitter switch pressed
    Pulse generation
    HAZ (IS-17) - Body ground
    GR- Body ground
    Hazard warning light signal
    Answer-back ON
    Pulse generation
    Answer-back OFF
    10 to 14 V

    HINT:
    *1: for LHD
    *2: for RHD

    1. If the result is not as specified, the junction block (ECU) may have a malfunction.

← PROBLEM SYMPTOMS TABLE (from Jan 2007)DIAGNOSIS SYSTEM (from Nov 2005) →