2005-2008 RAV4 · Service Manual DRIVE LINE

REPLACEMENT

Removal / installation · Vehicles built Jan 2007 – Jul 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


2. DRAIN MANUAL TRANSAXLE OIL (for Manual Transaxle)
  1. Remove the filler plug and gasket.

  1. Remove the drain plug and gasket, and drain the oil.

  1. Install a new gasket and the drain plug.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }


3. DRAIN TRANSFER OIL
  1. Remove the drain plug and gasket, and drain the oil.

  1. Install a new gasket and the drain plug.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }


4. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

C127633E01
  1. Using a brass bar and hammer, set the brass bar against position (1) as shown in the illustration and remove the drive shaft.

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the drive shaft boot.
    3. Do not allow the drive shaft to fall off.

  1. C127640
    Squeeze the ends of the snap ring, and remove the snap ring from the bearing bracket.

  1. Remove the bearing bracket bolt and remove the front drive shaft from the bearing bracket.

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the boot.
    3. Do not allow the drive shaft to fall off.

    HINT:
    If the connection is stiff, use a brass bar and hammer to lightly tap the edge of the inboard joint assembly RH and remove it.


5. REMOVE DRIVE SHAFT BEARING BRACKET
  1. Remove the 3 bolts and bracket from the transaxle.


6. REMOVE TRANSFER CASE OIL SEAL (for RH Side)

C126629E01
  1. Using SST, tap out the oil seal from the transfer.

    SST
    09308-00010  


7. INSTALL TRANSFER CASE OIL SEAL (for RH Side)

C110565E02
  1. Coat a new oil seal lip with MP grease.

  1. Using SST and a hammer, tap in the oil seal.

    SST
    09316-60011   (09316-00011)

    Standard depth:
    7.5 to 8.5 mm (0.30 to 0.33 in.)

    NOTICE:
    Do not damage the oil seal lip.


8. INSTALL DRIVE SHAFT BEARING BRACKET
  1. Install the bracket to the transaxle with the 3 bolt.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }


9. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH
  1. Coat the spline of the inboard joint shaft with gear oil.

  1. Align the shaft splines and securely insert the drive shaft.

    NOTICE:
    Do not damage the oil seal.

  1. C127640
    Squeeze the ends of the bracket hole snap ring and install it to the bearing bracket.

  1. Install the bearing bracket bolt.

    Torque:
    32.4 N*m{ 330 kgf*cm , 24 ft.*lbf }


10. ADD TRANSFER OIL

11. INSPECT TRANSFER OIL

  1. C110905
    Remove the transfer case plug No. 2 (for filler) and gasket.

  1. Check that the oil level is between 0 to 5.0 mm (0 to 0.20 in.) from the bottom lip of the case plug (for filler) hole.
    If the result is not as specified, add transfer oil.

    Oil grade:
    GL-5

    Viscosity:
    SAE 80W-90

    Standard capacity:
    0.45 liter (0.48 US qts, 0.40 Imp. qts)

    NOTICE:
    1. When adding oil, pour it slowly.
    2. Too much or too little oil will lead to transfer problems.

  1. When the oil level is too low, check for oil leakage.

  1. Install a new gasket into the case plug (for filler) and then tighten the plug.

    Torque:
    39 N*m{ 398 kgf*cm , 28 ft.*lbf }


12. ADD MANUAL TRANSAXLE OIL (for Manual Transaxle)

13. INSPECT MANUAL TRANSAXLE OIL (for Manual Transaxle)
  1. Stop the vehicle in a level place.

  1. Remove the transaxle filler plug and gasket.

  1. D025304E21
    Check that the oil level is between 0 to 5 mm (0 to 0.20 in.) from the bottom lip of the filler plug opening. If the result is not as specified, add transaxle oil.

    Oil grade:
    GL-4

    Viscosity:
    SAE 75W

    Standard capacity:
    2.5 liters (2.6 US qts, 2.2 Imp. qts)

    NOTICE:
    1. Too much or too little oil will lead to transaxle problems.
    2. After adjusting the oil level, drive the vehicle and check the oil level again.

  1. Check for oil leakage if the oil level is low.

  1. Install the transaxle filler plug and a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
← REPLACEMENT (Nov 2005 – Dec 2006)REPLACEMENT (from Aug 2007) →