2005-2008 RAV4 · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from Nov 2005


1. INSTALL FRONT DIFFERENTIAL SIDE GEAR

  1. C083137E01
    Coat the 2 front differential side gears, 2 side gear thrust washers, 2 front differential pinions and 2 pinion thrust washers with ATF, and install them to the differential case.


2. INSTALL NO. 1 FRONT DIFFERENTIAL PINION SHAFT

  1. C083135E01
    Coat the front differential pinion shaft with ATF, and install it to the differential case.


3. INSPECT FRONT DIFFERENTIAL SIDE GEAR BACKLASH

  1. C083138E01
    Using a dial indicator, measure the backlash of the side gear.

    Standard backlash:
    0.05 to 0.20 mm (0.0020 to 0.0070 in.)

    Standard thrust washer thickness:
    Thickness
    Thickness
    1.0 mm (0.0394 in.)
    1.2 mm (0.0472 in.)
    1.1 mm (0.0433 in.)
    1.3 mm (0.0512 in.)


4. INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

  1. C060005E01
    Using a pin punch and hammer, tap in the pinion shaft straight pin.

  1. C060006E01
    Using a chisel and hammer, stake the differential case.


5. INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

  1. D025218E03
    Using SST and a press, press in the front differential case tapered roller bearing rear inner race to the differential case.
    SST
    09608-06041  

  1. D025219E02
    Using SST and a hammer, tap in the case washer and front differential case tapered roller bearing rear outer race to the transaxle case.
    SST
    09950-60020   (09951-00710)
    09950-70010   (09951-07100)


6. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

  1. D025216E01
    Using SST and a press, press in the front differential case tapered roller bearing front inner race to the differential case.
    SST
    09608-06041  

  1. D025217E01
    Using SST and a hammer, tap in the front differential case tapered roller bearing front outer race to the transaxle housing.
    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07100)
    09950-60010   (09951-00340)


7. INSTALL FRONT DIFFERENTIAL RING GEAR

  1. D025215E03
    Using ATF and heater, heat the front differential ring gear to 90 to 110°C (194.0 to 230.0°F).

  1. Clean the contact surface of the front differential case.

  1. C083132E02
    Align the matchmarks, and install the front differential ring gear case quickly.

  1. C083133E01
    Tighten the 10 bolts.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }


8. INSPECT TAPERED ROLLER BEARING PRELOAD

  1. C083139E01
    Install the differential assembly to the transaxle case.

  1. Install the transaxle housing to the transaxle case.

  1. C050259E01
    Install the 16 bolts.

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf } for bolt A
    29 N*m{ 296 kgf*cm , 21 ft.*lbf } for bolt B and C

    HINT:
    Each bolt length is indicated below.

    Bolt length:
    50 mm (1.97 in.) for bolt A and B
    42 mm (1.65 in.) for bolt C

  1. C083572E01
    Using SST, turn the differential.
    SST
    09564-32011  

  1. C083572E01
    Using SST and torque wrench, measure the preload of the differential.
    SST
    09564-32011  

    Torque:
    Standard turning torque at 60 rpm:
    0.20 to 0.69 N*m{ 2.0 to 7.0 kgf*cm , 1.8 to 6.1 in.*lbf } for new
    0.10 to 0.35 N*m{ 1.0 to 3.6 kgf*cm , 0.9 to 3.1 in.*lbf } for used

    Standard adjusting shim thickness:
    Mark
    Thickness
    0
    1.90 mm (0.074 in.)
    1
    1.95 mm (0.077 in.)
    2
    2.00 mm (0.079 in.)
    3
    2.05 mm (0.081 in.)
    4
    2.10 mm (0.083 in.)
    5
    2.15 mm (0.085 in.)
    6
    2.20 mm (0.087 in.)
    7
    2.25 mm (0.089 in.)
    8
    2.30 mm (0.091 in.)
    9
    2.35 mm (0.093 in.)
    A
    2.40 mm (0.094 in.)
    B
    2.45 mm (0.096 in.)
    C
    2.50 mm (0.098 in.)
    D
    2.55 mm (0.100 in.)
    E
    2.60 mm (0.102 in.)
    F
    2.65 mm (0.104 in.)
    G
    2.70 mm (0.106 in.)
    H
    2.75 mm (0.108 in.)
    J
    2.80 mm (0.110 in.)

  1. D009182E01
    Remove the 16 bolts.

  1. Using a practic-faced hammer, remove the transaxle housing.

  1. C083139E01
    Remove the differential.


9. INSTALL TRANSAXLE HOUSING OIL SEAL

D025606E01
  1. Coat the lip of a new oil seal with a little amount of MP grease.

  1. Using SST and a hammer, tap in the oil seal.

    SST
    09350-32014   (09351-32150)
    09950-70010   (09951-07150)


10. INSTALL DIFFERENTIAL SIDE BEARING RETAINER OIL SEAL

D025605E01
  1. Coat the lip of a new oil seal with a little amount of MP grease.

  1. Using SST and a hammer, tap in the oil seal.

    SST
    09350-32014   (09351-32150)
    09950-70010   (09951-07150)

← INSPECTION (from Nov 2005)COMPONENTS (from Nov 2005) →