2005-2008 RAV4 · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Nov 2005


1. REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY
  1. Remove the bolt and hole cover from the transaxle.

  1. Remove the O-ring from the hole cover.


2. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. D008032E01
    Remove the nut, washer and control shaft lever.

  1. D008033E01
    Using a screwdriver, unstake the lock plate and remove the lock nut and lock plate.

  1. D008034E03
    Remove the 2 bolts and pull out the park/neutral position switch.


3. REMOVE BREATHER PLUG HOSE
  1. Remove the breather plug hose from the breather plug.


4. REMOVE OIL COOLER OUTLET TUBE UNION

C127449
  1. Remove the union.

  1. Remove the O-ring from the union.


5. REMOVE OIL COOLER INLET TUBE UNION

C127450
  1. Remove the union.

  1. Remove the O-ring from the union.


6. REMOVE SPEED SENSOR

  1. D003900E01
    Remove the 2 bolts and 2 speed sensors from the transaxle.

  1. Remove the 2 O-rings from the sensors.


7. REMOVE NO. 1 TRANSAXLE CASE PLUG

  1. C134982
    Remove the 4 plugs from the transaxle.

  1. Remove the 4 O-rings from the 4 plugs.


8. FIX AUTOMATIC TRANSAXLE ASSEMBLY

D009176E01

9. REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

  1. D009177E01
    Remove the 18 bolts.

  1. Remove the oil pan and 3 magnets.

  1. Remove the gasket from the oil pan.


10. INSPECT AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

  1. AT00103E01
    Remove the magnets and use them to collect any steel chips. Examine the clips and particles in the pan and on the magnet to determine what type of wear has occurred in the transaxle.
    Steel (magnetic): bearing, gear and plate wear
    Brass (non-magnetic): bush wear


11. REMOVE VALVE BODY OIL STRAINER ASSEMBLY

  1. D009179E01
    Remove the 3 bolts and oil strainer.

  1. D009180E01
    Remove the O-ring from the oil strainer.


12. REMOVE TRANSMISSION WIRE

  1. C130917E01
    Remove the 5 connectors from the shift solenoid valves.

  1. Remove the bolt, clamp and ATF temperature sensor.

  1. D003547E08
    Remove the bolt and transaxle solenoid wire from the transaxle.

  1. D003636E03
    Remove the O-ring from the transaxle solenoid wire.


13. REMOVE TRANSMISSION VALVE BODY ASSEMBLY

  1. D003553E01
    Support the valve body assembly and remove the 17 bolts and the valve body assembly.


14. REMOVE NO. 1 GOVERNOR APPLY GASKET

  1. C083127E01
    Remove the governor apply gasket from the transaxle.


15. REMOVE TRANSAXLE CASE 2ND BRAKE GASKET

  1. C083128E01
    Remove the 2nd brake gasket from the transaxle.


16. REMOVE BRAKE DRUM GASKET

  1. C083129E01
    Remove the brake drum gasket from the transaxle.


17. REMOVE CHECK BALL BODY

  1. D003554E02
    Remove the check ball body and spring from the transaxle.


18. REMOVE C-3 ACCUMULATOR PISTON

  1. D003555E01
    Remove the compression spring from the C-3 accumulator piston.

  1. D003556E02
    Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-3 accumulator piston.

    NOTICE:
    1. Applying compressed air may cause the piston to jump out. When removing the piston, hold it with your hand using a waste cloth.
    2. Make sure not to spatter ATF when applying compressed air.

  1. D003902E02
    Remove the O-ring from the C-3 accumulator piston.


19. REMOVE C-1 ACCUMULATOR PISTON

  1. D003557E02
    Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-1 accumulator piston and compression spring.

    NOTICE:
    1. Applying compressed air may cause the piston to jump out. When removing the piston, hold it with your hand using a waste cloth.
    2. Make sure not to spatter ATF when applying compressed air.

  1. D003903E01
    Remove the 2 O-rings from the C-1 accumulator piston.


20. REMOVE B-3 ACCUMULATOR PISTON

  1. D003558E02
    Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the B-3 accumulator piston and 2 compression springs.

    NOTICE:
    1. Applying compressed air may cause the piston to jump out. When removing the piston, hold it with your hand using a waste cloth.
    2. Make sure not to spatter ATF when applying compressed air.

  1. D003904E05
    Remove the O-ring from the B-3 accumulator piston.


21. REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY

  1. D003560E03
    Remove the 2 bolts, manual detent spring and cover.


22. REMOVE PARKING LOCK PAWL BRACKET

  1. C056727E01
    Remove the 2 bolts and parking lock pawl bracket.


23. REMOVE MANUAL VALVE LEVER SHAFT RETAINER SPRING

  1. D003559E01
    Using needle-nose pliers, remove the retainer spring.


24. REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY

  1. D003563E01
    Using a chisel and hammer, unstake and remove the manual valve lever spacer.

  1. D003564E01
    Using a pin punch and hammer, tap out the manual valve lever shaft spring pin.

    HINT:
    Slowly drive out the pin so that it will not fall into the transaxle.

  1. D003565E02
    Remove the manual valve lever shaft and manual valve lever.


25. REMOVE PARKING LOCK ROD SUB-ASSEMBLY

  1. D003905E01
    Remove the parking lock rod from the manual valve lever.


26. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

  1. D003566E02
    Using a screwdriver, pry out the oil seal from the transaxle.


27. INSPECT INPUT SHAFT END PLAY
  1. Fix the transaxle case with the oil pump side facing up.

  1. D008046E01
    Using a dial indicator, measure the input shaft end play.

    Standard end play:
    0.26 to 1.25 mm (0.0103 to 0.0492 in.)


28. REMOVE NO. 1 TRANSAXLE CASE PLUG

  1. C134983
    Remove the 2 plugs.

  1. Remove the 2 O-rings from the plug.


29. REMOVE TRANSAXLE HOUSING

  1. D009182E01
    Remove the 16 bolts.

  1. Tap on the circumference of the transaxle housing with a plastic-faced hammer to remove the transaxle housing from the transaxle.

    NOTICE:
    Differential may be accidentally removed when the transaxle housing is removed.


30. REMOVE UNDERDRIVE CYLINDRICAL ROLLER BEARING

  1. D003606E02
    Using SST, remove the cylindrical roller bearing from the transaxle.
    SST
    09514-35011  


31. REMOVE UNDERDRIVE OUTPUT SHAFT OIL SEAL RING

  1. D003915E07
    Remove the oil seal ring from the transaxle housing.


32. REMOVE OIL PUMP ASSEMBLY

  1. D003569E03
    Remove the 7 bolts and oil pump assembly from the transaxle.


33. REMOVE THRUST NEEDLE ROLLER BEARING

  1. D025505E03
    Remove thrust needle roller bearing from the underdrive planetary gear.


34. REMOVE NO. 2 THRUST BEARING UNDERDRIVE RACE

  1. D025506E04
    Remove the thrust bearing race from the underdrive planetary gear.


35. REMOVE FRONT DIFFERENTIAL ASSEMBLY

  1. D003577E01
    Remove the front differential from the transaxle.


36. REMOVE OVERDRIVE BRAKE GASKET

  1. D003573E01
    Remove the 2 overdrive brake gaskets from the transaxle.


37. REMOVE FORWARD CLUTCH ASSEMBLY

  1. D003574E03
    Remove the forward clutch from the transaxle.

  1. D003906E02
    Remove the thrust bearing from the forward clutch.


38. REMOVE MULTIPLE DISC CLUTCH CLUTCH HUB

  1. D003575E01
    Remove the thrust bearing, multiple clutch hub, needle roller bearing and bearing race from the transaxle.


39. REMOVE UNDERDRIVE PLANETARY GEAR ASSEMBLY

  1. D003576E03
    Remove the bolt and parking pawl shaft clamp.

  1. D009201E01
    Remove the parking lock pawl shaft.

  1. D008048E01
    Push the parking lock pawl.

    HINT:
    Failure to do so will cause the interference when the underdrive planetary gear is removed.

  1. D003579E04
    Remove the underdrive planetary gear from the transaxle.

    NOTICE:
    Be careful so that the underdrive planetary gear assembly will not fall out.

  1. D008049E01
    Remove the spring, pawl pin and parking lock pawl.


40. REMOVE UNDERDRIVE CLUTCH ASSEMBLY

  1. D003580E02
    Remove the underdrive clutch assembly, needle roller bearing, thrust bearing underdrive race from the transaxle.


41. REMOVE UNDERDRIVE 1-WAY CLUTCH ASSEMBLY

  1. D003581E02
    Using a screwdriver, pry out the snap ring from the transaxle.

  1. D003627E03
    Remove the 1-way clutch from the transaxle.

  1. D009198E01
    Remove the outer race retainer from the 1-way clutch.


42. REMOVE NO. 2 UNDERDRIVE CLUTCH DISC

  1. D008050E01
    Using a screwdriver, pry out the snap ring from the transaxle.

  1. D009197E01
    Remove the flange, 3 discs and 3 plates from the transaxle.


43. INSPECT NO. 2 UNDERDRIVE CLUTCH DISC

D009196E01
Check to see if the sliding surface of the disc, plate and flange are worn or burnt.
If necessary, replace them.

NOTICE:
  1. If the lining of the disc is peeling off or discolored, or even if a part of the groove is defaced, replace all discs.
  2. Before assembling new discs, soak them in ATF for at least 15 minutes.


44. REMOVE UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

  1. D003610E01
    Using SST, a snap ring expander and press, remove the snap ring from the transaxle.
    SST
    09387-00020  

  1. D008051E01
    Remove the underdrive brake return spring from the underdrive brake piston.


45. INSPECT UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

  1. D003806E01
    Using a vernier caliper, measure the free length of the underdrive brake return spring together with the spring seat.

    Standard free length:
    14.04 mm (0.5213 in.)


46. REMOVE UNDERDRIVE CLUTCH DRUM OIL SEAL RING

  1. D003914E04
    Remove the 2 oil seal rings from the transaxle.


47. REMOVE NO. 1 TRANSAXLE CASE PLUG

  1. C134984
    Remove the 2 plugs from the transaxle rear cover.

  1. Remove the 2 O-rings from the 2 plugs.


48. REMOVE REAR TRANSAXLE COVER SUB-ASSEMBLY

  1. D009943E02
    Remove the 11 bolts.

  1. Tap the circumference of the rear cover with a plastic-faced hammer to remove the transaxle rear cover from the transaxle.

  1. D009184E01
    Remove the 2 outer rear clutch oil seal rings from the transaxle rear cover.

  1. C083140E01
    Using a T30 ''torx'' socket wrench, remove the 2 screws and transaxle rear cover plate.

  1. D003801E01
    Using SST, remove the needle-roller bearing from the transaxle rear cover.
    SST
    09387-00041   (09387-01010, 09387-01030, 09387-01040)


49. REMOVE UNDERDRIVE BRAKE PISTON

  1. D003799E02
    Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the underdrive brake piston.

  1. D003794E02
    Remove the 2 O-rings from the underdrive brake piston.


50. REMOVE BRAKE APPLY TUBE

  1. D025510E01
    Remove the bolt, clamp and 2 brake apply tubes.

  1. Remove the brake apply tube from the clamp.


51. REMOVE FRONT CLUTCH APPLY TUBE

52. REMOVE NO. 1 GOVERNOR APPLY GASKET

  1. D003591E01
    Using a screwdriver, remove the 2 governor apply gaskets.


53. REMOVE DIRECT CLUTCH ASSEMBLY

  1. D003586E01
    Remove the thrust bearing and direct clutch from the transaxle.

  1. D008053E01
    Remove the bearing race from the direct clutch.


54. REMOVE REAR PLANETARY SUN GEAR ASSEMBLY

  1. D003587E01
    Remove the rear planetary sun gear from the transaxle.

  1. D003791E01
    Remove the rear planetary sun gear thrust bearing from the rear planetary sun gear.

  1. D008054E01
    Remove the No. 1 thrust washer and 1-way clutch thrust bearing from the rear planetary sun gear.


55. REMOVE 1-WAY CLUTCH ASSEMBLY

  1. D008055E01
    Remove the 1-way clutch from the transaxle.

  1. D003909E02
    Remove the 1-way clutch inner race from the 1-way clutch.


56. REMOVE 1-WAY CLUTCH SLEEVE OUTER

D003589E03

57. REMOVE 2ND BRAKE CLUTCH DISC
  1. Using a screwdriver, remove the 2nd brake hole snap ring.

  1. C129388
    Remove the flange, 3 discs and 3 plates from the transaxle.


58. INSPECT 2ND BRAKE CLUTCH DISC

  1. D004083E01
    Check to see if the sliding surface of the disc, plate and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of the disc is peeling off or discolored, or even if a part of the printed number is defaced, replace all discs.
    2. Before assembling new discs, soak them in ATF for at least 15 minutes.


59. REMOVE 2ND BRAKE PISTON ASSEMBLY

  1. D008058E03
    Using a screwdriver, pry out the snap ring.

  1. D008059E01
    Remove the 2nd brake piston from the transaxle.


60. REMOVE 1ST AND REVERSE BRAKE CLUTCH DISC

  1. D009941E01
    Remove the flange, 5 discs and 5 plates from the transaxle.


61. INSPECT 1ST AND REVERSE BRAKE CLUTCH DISC

  1. D009189E01
    Check to see if the sliding surface of the disc, plate and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of the disc is peeling off or discolored, or even if a part of the groove is defaced, replace all discs.
    2. Before assembling new discs, soak them in ATF for at least 15 minutes.


62. REMOVE REAR PLANETARY GEAR ASSEMBLY

  1. D003616E02
    Using a screwdriver, pry out the snap ring from the brake hub.

  1. D008062E01
    Remove the rear planetary gear from the transaxle.

  1. D003910E01
    Remove the thrust washer from the rear planetary gear.

  1. D003593E01
    Remove the thrust bearing race from the rear planetary gear.


63. REMOVE INPUT SUN GEAR

  1. D003873E03
    Remove the 2 thrust bearings, bearing race and input sun gear from the transaxle.


64. REMOVE FRONT PLANETARY GEAR ASSEMBLY

  1. D003595E02
    Using a chisel and hammer, unstake the lock washer.

    NOTICE:
    Push down all claws of the washer. Otherwise SST cannot be fully pressed against the nut and cannot loosen the nut.

  1. D003596E01
    Using SST, remove the nut.
    SST
    09387-00030  
    09387-00080  

  1. D003597E01
    Using SST and a press, remove the front planetary gear from the counter drive gear.
    SST
    09950-60010   (09951-00450)

  1. D008063E01
    Remove the front planetary gear from the brake hub.


65. REMOVE FRONT PLANETARY RING GEAR

  1. D003615E03
    Using a screwdriver, pry out the brake hub snap ring and front planetary ring gear from the brake hub.


66. REMOVE 1ST AND REVERSE BRAKE PISTON

  1. D003600E01
    Using SST, a press and ring expander, remove the snap ring and piston return spring.
    SST
    09387-00070  

    NOTICE:
    1. Stop the press when the spring sheet is lowered 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove, preventing the spring sheet from deforming.
    2. Do not expand the snap ring excessively.

  1. D008061E01
    Remove the 1st and reverse brake return spring from the 1st and reverse brake piston.

  1. D003800E01
    Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle to remove the 1st and reverse brake piston.

    NOTICE:
    1. Applying compressed air may cause the piston to jump out. When removing the piston, hold it with your hand using a waste cloth.
    2. Make sure not to spatter ATF when applying compressed air.

  1. D003913E01
    Remove the 2 O-rings from the 1st and reverse brake piston.


67. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

  1. D003811E01
    Using a vernier caliper, measure the free length of the 1st and reverse brake return spring together with the spring seat.

    Standard free length:
    15.51 mm (0.6106 in.)


68. REMOVE COUNTER DRIVE GEAR

  1. D003601E01
    Using SST and a press, press out the counter drive gear from the transaxle.
    SST
    09950-60010   (09951-00600)
    09950-70010   (09951-07100)

  1. D003602E01
    As shown in the illustration, tighten the 2 bolts evenly and make a clearance of approximately. 20.0 mm (0.797 in.) between the counter drive gear and the inner race.

  1. D003603E02
    Using SST, remove the tapered roller bearing.
    SST
    09950-60010   (09951-00600)
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04011, 09958-04011)

  1. D003798E01
    Using a brass bar and hammer, tap out the 2 counter drive gear bearing outer races from the transaxle.


69. REMOVE COUNTER DRIVE GEAR HOLE SNAP RING

  1. D003604E01
    Using a screwdriver, pry out the snap ring from the transaxle.


70. REMOVE NO. 2 BREATHER PLUG

71. REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE

  1. D003607E01
    Remove the bolt, the transaxle apply tube clamp and the differential gear lube apply tube from the transaxle.

← COMPONENTS (from Nov 2005)INSPECTION (from Nov 2005) →