2005-2008 RAV4 · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Jan 2007 – Jul 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. INSTALL FAN SHROUD WITH COOLING FAN

  1. A114328
    Install the fan shroud with cooling fan with the 2 bolts to the radiator.

    Torque:
    10.5 N*m{ 107 kgf*cm , 8 ft.*lbf }


2. INSTALL RADIATOR ASSEMBLY
  1. Install the 4 fan shroud cushions to the cooler condenser.

  1. Set the cooler condenser to the fan shroud.

  1. A114339
    Install the 2 radiator support lower cushions to the fan shroud.

  1. Install the radiator with cooler condenser and fan shroud to the radiator support lower.


3. INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY

  1. A112338
    Install the upper radiator support with the 4 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


4. INSTALL NO. 2 FAN SHROUD

  1. A112186
    Attach the 2 claws to install the No. 2 fan shroud and install the 2 bolts.

    Torque:
    10.5 N*m{ 107 kgf*cm , 8 ft.*lbf }


5. INSTALL UPPER RADIATOR SUPPORT BRACKET

  1. A112185
    Install the bracket with the 2 bolts.

    Torque:
    19 N*m{ 193 kgf*cm , 14 ft.*lbf }


6. CONNECT HORN CONNECTOR
  1. Connect the 2 horn connectors.


7. CONNECT NO. 2 WATER BY-PASS HOSE
  1. Connect the by-pass hose to the radiator and radiator reservoir.

    HINT:
    The direction of the hose clamp is indicated in the illustration.


8. CONNECT NO. 2 RADIATOR HOSE

HINT:
The direction of the hose clamp is indicated in the illustration.


9. CONNECT NO. 1 RADIATOR HOSE

HINT:
The direction of the hose clamp is indicated in the illustration.


A112335E02

10. CONNECT OIL COOLER OUTLET HOSE (for Automatic Transaxle)

11. CONNECT OIL COOLER INLET HOSE (for Automatic Transaxle)

12. CONNECT COOLING FAN MOTOR HARNESS

  1. Attach the harness with the 5 clamps.

    A132420

  1. Connect the 2 fan motor connectors.


13. INSTALL NO. 1 WATER BY-PASS PIPE
  1. Install the by-pass pipe with the 2 bolts to the upper radiator support.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the No. 1 radiator hose to the pipe.


14. CONNECT NO. 5 WATER BY-PASS HOSE
  1. Connect the by-pass hose to the radiator.


15. CONNECT NO. 1 WATER BY-PASS HOSE

  1. Connect the by-pass hose to the radiator and radiator reservoir.

    A132425E01


16. CONNECT HOOD LOCK SWITCH CONNECTOR

A112308

17. INSTALL RADIATOR GRILL SUB-ASSEMBLY

  1. B136794
    Install the radiator grille with the 6 claws.

  1. B135282
    Install the 4 bolts and 4 nuts.


18. INSTALL BATTERY

19. INSTALL BATTERY CLAMP SUB-ASSEMBLY
  1. Install the battery clamp with the bolt and nut.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf } for nut
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf } for bolt


20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

21. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the cylinder block drain cock plug.

    Torque:
    12.7 N*m{ 130 kgf*cm , 10 ft.*lbf }

  1. Add TOYOTA Super Long Life Coolant (SLLC) to the radiator reservoir filler opening.

  1. A112307E01
    Continue adding TOYOTA SLLC until it is filled to the B line at the base of the reservoir's filler neck.

    HINT:
    The B line is the lower edge of the inner wall of the filler neck.

    Standard capacity:
    Item
    Specified Condition
    A/T
    6.4 liters (6.8 US qts, 5.6 Imp. qts)
    M/T
    6.3 liters (6.7 US qts, 5.5 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant. If the coolant level drops below the B line, add TOYOTA SLLC to the B line.

  1. Install the radiator reservoir cap.

  1. Start the engine and warm it up until the cooling fan operates. While the cooling fan operates, circulate the coolant for several minutes.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Specified Condition
      Manual Air Conditioning System
      Fan speed: Any setting except OFF
      Temperature: Toward WARM
      Air conditioning switch: OFF
      Automatic Air Conditioning System
      Temperature: Toward MAX
      Air conditioning switch: OFF

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.

      NOTICE:
      1. Make sure that the radiator reservoir still has some coolant in it.
      2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
      3. If there is not enough coolant, the engine may burn out or overheat.
      4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the B line.
      5. Run the engine at 2,000 rpm until the coolant level has stabilized.

  1. Press the No. 1 and No. 2 radiator hoses several times by hand to bleed air.

    CAUTION:
    When pressing the radiator hoses:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the radiator fan.

  1. Stop the engine and wait until the coolant cools down to ambient temperature.

  1. A112306
    Check that the coolant level is between the FULL and LOW line.
    If the coolant level is below the LOW line, repeat all of the procedures above.
    If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW line.


22. CHECK FOR ENGINE COOLANT LEAKS
  1. Remove the radiator reservoir cap.

    CAUTION:
    To avoid the danger of being burned, do not remove the radiator reservoir cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator reservoir.

  1. A112194E01
    Fill the radiator reservoir with coolant, and then attach a radiator cap tester.

  1. Warm up the engine.

  1. Pump the radiator cap tester to 118 kPa (1.2 kgf/cm2, 17.1 psi), and then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leakage.
    If there are no signs of external coolant leaks, check the heater core, cylinder block and head.

  1. Reinstall the radiator cap.


23. INSTALL RADIATOR SUPPORT OPENING COVER
← INSTALLATION (Nov 2005 – Dec 2006)INSTALLATION (from Aug 2007) →