Removal / installation · Vehicles built from Aug 2007
1.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.
REMOVE BATTERY CLAMP SUB-ASSEMBLY
Remove the bolt and loosen the nut.
Detach the 2 wire harness clamps.
Detach the hook of the battery clamp from the front battery bracket, and then remove the battery clamp.
3.
REMOVE BATTERY
Remove the battery and battery insulator.
4.
REMOVE NO. 1 ENGINE UNDER COVER
Remove the 2 bolts, 4 screw, 10 clips and under cover.
5.
DRAIN ENGINE COOLANT
Loosen the radiator drain cock plug.
HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.
Remove the radiator reservoir cap.
CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
Loosen the 2 cylinder block drain cock plugs.
6.
REMOVE V-BANK COVER SUB-ASSEMBLY
Detach the 3 clips and remove the V-bank cover.
7.
REMOVE RADIATOR SUPPORT OPENING COVER
Remove the 9 clips and cover.
8.
REMOVE RADIATOR GRILLE SUB-ASSEMBLY
Remove the 4 bolts and 4 nuts.
Detach the 6 claws and remove the radiator grille.
9.
DISCONNECT HOOD LOCK SWITCH ASSEMBLY
Disconnect the hood lock switch connector.
Disconnect the wire from the clamp.
Remove the 3 bolts and disconnect the hood lock switch assembly.
10.
REMOVE NO. 1 WATER BY-PASS HOSE
Remove the No. 1 water by-pass hose from the radiator reservoir and No. 1 water by-pass pipe.
11.
REMOVE NO. 5 WATER BY-PASS HOSE
Remove the No. 5 water by-pass hose from the radiator and No. 1 water by-pass pipe.
12.
REMOVE NO. 1 WATER BY-PASS PIPE
Disconnect the No. 2 radiator hose from the No. 1 water by-pass pipe.
Remove the 2 bolts and No. 1 water by-pass pipe.
13.
DISCONNECT COOLING FAN ECU HARNESS
Disconnect the 2 cooling fan ECU connectors.
Detach the 3 harness clamps from the fan shroud and upper radiator support.
14.
REMOVE UPPER RADIATOR SUPPORT BRACKET
Remove the 2 bolts and 2 upper radiator support brackets.
15.
REMOVE NO. 2 FAN SHROUD
Remove the 2 bolts.
Detach the 2 claws and No. 2 fan shroud.
16.
REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY
Remove the 4 bolts and upper radiator support sub-assembly.
17.
DISCONNECT OIL COOLER INLET HOSE
18.
DISCONNECT OIL COOLER OUTLET HOSE
19.
DISCONNECT NO. 1 RADIATOR HOSE
20.
DISCONNECT NO. 2 RADIATOR HOSE
21.
REMOVE NO. 2 WATER BY-PASS HOSE
Remove the No. 2 water by-pass hose from the radiator reservoir and radiator.
22.
REMOVE RADIATOR ASSEMBLY
Detach the cooler condenser from the radiator.
HINT:
After detaching the condenser, make sure that all 4 fan shroud cushions are present.
Remove the radiator with the 2 radiator support lower cushions.
HINT:
After detaching the radiator, make sure that all 2 lower radiator supports are present.
Disconnect the 2 oil cooler hoses from the radiator.
Remove the 2 bolts and 2 oil cooler hoses.
23.
REMOVE FAN SHROUD WITH COOLING FAN
Remove the 2 bolts and fan shroud with cooling fan from the radiator.