2005-2008 RAV4 · Service Manual RESTRAINTS

B1655/37 Driver Side Seat Belt Buckle Switch Circuit Malfunction

Diagnostic trouble codes · Vehicles built Nov 2005 – Dec 2006

Versions by build date: Nov 2005 – Dec 2006 from Jan 2007

DESCRIPTION

The driver side seat belt buckle switch circuit consists of the center airbag sensor and the front seat inner belt.
DTC B1655/37 is recorded when a malfunction is detected in the driver side seat belt buckle switch circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1655/37
When one of following conditions is met:
  1. The center airbag sensor receives a line short signal, an open signal, a short to ground signal or a short to B+ signal in the driver side seat belt buckle switch circuit for 2 seconds.
  2. Driver side seat inner belt malfunction
  3. Center airbag sensor malfunction
  1. Floor wire
  2. Driver side seat inner belt
  3. Center airbag sensor

WIRING DIAGRAM

C123546E03

INSPECTION PROCEDURE


1. CHECK FOR DTC
H100892E04
  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

    HINT:
    DTCs other than DTC B1655/37 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


2. CHECK CONNECTION OF CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and the driver side seat inner belt.

    OK:
    The connectors are connected.



NG
CONNECT CONNECTOR
OK


3. CHECK FLOOR WIRE (OPEN)
C128685E01
  1. Disconnect the connectors from the center airbag sensor and the driver side seat inner belt.

  1. Using a service wire, connect K1-12 (DBE-) and K1-11 (DBE+)*1 or L18-12 (DBE-) and L18-11 (DBE+)*2 of connector B.

    HINT:
    *1: for LHD
    *2: for RHD

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    for LHD:
    Tester Connection
    Specified Condition
    K3-4 (LBE+) - K3-3 (LBE-)
    Below 1 Ω
    for RHD:
    Tester Connection
    Specified Condition
    L16-4 (RBE+) - L16-3 (RBE-)
    Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE
OK


4. CHECK FLOOR WIRE (SHORT)
C128684E02
  1. Disconnect the service wire from connector B.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    for LHD:
    Tester Connection
    Specified Condition
    K3-4 (LBE+) - K3-3 (LBE-)
    1 MΩ or higher
    for RHD:
    Tester Connection
    Specified Condition
    L16-4 (RBE+) - L16-3 (RBE-)
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


5. CHECK FLOOR WIRE (TO B+)
C128684E02
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    for LHD:
    Tester Connection
    Specified Condition
    K3-3 (LBE-) - Body ground
    Below 1 V
    K3-4 (LBE+) - Body ground
    Below 1 V
    for RHD:
    Tester Connection
    Specified Condition
    L16-3 (LBE-) - Body ground
    Below 1 V
    L16-4 (LBE+) - Body ground
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE
OK


6. CHECK FLOOR WIRE (TO GROUND)
C128684E02
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    for LHD:
    Tester Connection
    Specified Condition
    K3-3 (LBE-) - Body ground
    1 MΩ or higher
    K3-4 (LBE+) - Body ground
    1 MΩ or higher
    for RHD:
    Tester Connection
    Specified Condition
    L16-3 (LBE-) - Body ground
    1 MΩ or higher
    L16-4 (LBE+) - Body ground
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


7. CHECK DRIVER SIDE SEAT INNER BELT ASSEMBLY
H100892E04
  1. Connect the connectors to the center airbag sensor and the driver side seat inner belt.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

    HINT:
    DTCs other than DTC B1655/37 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


8. REPLACE DRIVER SIDE SEAT INNER BELT ASSEMBLY
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the driver side seat inner belt (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.


NEXT


9. CHECK CENTER AIRBAG SENSOR ASSEMBLY
H100892E04
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

    HINT:
    DTCs other than DTC B1655/37 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

END


← B1653/35 Seat Position Airbag Sensor Circuit Malfunction (from Jan 2007)B1655/37 Driver Side Seat Belt Buckle Switch Circuit Malfunction (from Jan 2007) →