DISASSEMBLY
Removal / installation · Vehicles built from Nov 2005
| 1.
INSPECT 4TH GEAR THRUST CLEARANCE |
 |
Using a feeler gauge, measure the thrust clearance.
- Standard clearance:
- 0.10 to 0.57 mm (0.0039 to 0.0224 in.)
If the clearance is out of the specification, replace the No. 2 transaxle clutch hub, 4th gear or input shaft rear radial ball bearing.
| 2.
INSPECT 3RD GEAR THRUST CLEARANCE |
 |
Using a dial indicator, measure the thrust clearance.
- Standard clearance:
- 0.10 to 0.35 mm (0.0039 to 0.0138 in.)
If the clearance is out of the specification, replace the No. 2 transaxle clutch hub, 3rd gear or input shaft.
| 3.
INSPECT 4TH GEAR RADIAL CLEARANCE |
 |
Using a dial indicator, measure the radial clearance.
- Standard clearance:
Bearing
|
Specified Condition
|
KOYO made
|
0.009 to 0.053 mm (0.0004 to 0.0021 in.)
|
NSK made
|
0.009 to 0.051mm (0.0004 to 0.0020 in.)
|
If the clearance is out of the specification, replace the 4th gear, needle roller bearing or input shaft.
| 4.
INSPECT 3RD GEAR RADIAL CLEARANCE |
 |
Using a dial indicator, measure the gear radial clearance.
- Standard clearance:
Bearing
|
Specified Condition
|
KOYO made
|
0.009 to 0.053 mm (0.0004 to 0.0021 in.)
|
NSK made
|
0.009 to 0.051mm (0.0004 to 0.0020 in.)
|
If the clearance is out of the specification, replace the 3rd gear, needle roller bearing or input shaft.
| 5.
REMOVE 4TH GEAR |
 |
Hold the input shaft assembly in a vise with soft jaws.
Using 2 screwdrivers and a hammer, tap out the input shaft rear bearing shaft snap ring from the input shaft.
- HINT:
- Cover with a shop rag to keep the snap ring from flying off.
- Using SST and a press, press out the input shaft rear bearing and 4th gear.
- SST
- 09950-00020
- NOTICE:
- Do not overtighten the SST.
| 6.
REMOVE 4TH GEAR NEEDLE ROLLER BEARING |
 |
Remove the needle roller bearing from the input shaft.
| 7.
REMOVE 2ND SYNCHRONIZER OUTER RING |
 |
Remove the 2nd synchronizer outer ring (No. 4 synchronizer ring) from the No. 2 transaxle clutch hub.
| 8.
REMOVE 4TH GEAR BUSH |
 |
Remove the 4th gear bush from the No. 2 transaxle clutch hub.
| 9.
REMOVE 3RD GEAR |
 |
Using 2 screwdrivers and a hammer, tap out the No. 2 clutch hub setting shaft snap ring from the input shaft.
- HINT:
- Cover with a shop rag to keep the snap ring from flying off.
- Using SST and a press, press out the No. 2 transaxle clutch hub and 3rd gear from the input shaft.
- SST
- 09950-00020
- NOTICE:
- Do not overtighten the SST.
| 10.
REMOVE 3RD GEAR NEEDLE ROLLER BEARING |
 |
Remove the needle roller bearing from the input shaft.
| 11.
REMOVE NO. 3 SYNCHRONIZER RING |
 |
Remove the No. 3 synchronizer ring from the 3rd gear.
| 12.
REMOVE NO. 2 TRANSAXLE HUB SLEEVE |
 |
Remove the No. 2 transaxle hub sleeve, 3 No. 2 synchromesh shifting keys and 3 No. 2 synchromesh shifting key springs from the No. 2 transaxle clutch hub.
- HINT:
- Cover with a shop rag to keep the shifting key and shifting key spring from flying off.
| 13.
REMOVE INPUT SHAFT FRONT BEARING |
 |
Using SST and a press, press out the input shaft front bearing (inner race) from the input shaft.
- NOTICE:
- Do not overtighten SST.